Soss UltraLatch User manual
Separate Unirose Bodies
Separate the unirose bodies as shown
in the illustration. The latch side unirose
will be stamped with part # LP22ALN
or # LP22ALE. The lock side unirose will
be stamped with part # LP22ALNO or
# LP22ALEO.
Chassis Disassembly
Use #2 square drive or #2 phillips screwdriver to remove chassis
from lock side unirose. The unirose will be stamped with either
part # LP22ALNO or # LP22ALEO.
If this is a 2" door installation (L3)
there will be spacers between
the chassis and unirose
at the 4 and 10
o’clock positions.
Tools needed to Change SOSS®
UltraLatch® Privacy Stops
Instructions for changing Privacy Stops from standard
Pull Side Configuration to Push Side Configuration
• #2 Sq. Drive Screwdriver (Robertson)
• #2 Phillips Screwdriver (Asian Model)
• 1/16" (1.59mm Hex Bit)
1
2
34
1
Remove Stop and Retainers
Use 1/16" (1.59 mm) hex bit to remove stops and retainers from
above assemblies and layout as shown below. The stops will be
stamped with their part numbers LPBAA3 and LPBAA4.
Note: The stop part numbers are located on the back side of
the part.
Orient Stops
Orient the stops into position shown below.
Stop
Part # LPBAA4
Stop
Part # LPBAA3
2-Hole Retainer
3-Hole Retainer
ScrewsScrews
Stop
Part # LPBAA3
Stop
Part # LPBAA4
3-Hole Retainer
2-Hole Retainer
ScrewsScrews
Screw at
10 O’clock
Screw at
10 O’clock
Spacer for
2” Doors Only
Spacer for
2” Doors Only
Chassis faces
9 O’clock Position
Chassis faces
3 O’clock Position
Unirose Set Up for
Left Hand Door (Factory Setup)
Unirose Set Up for
Right Hand Door (Chassis Rotated 180°)
Screw at
4 O’clock
Screw at
4 O’clock
Spacer for
2” Doors Only
Spacer for
2” Doors Only
Part #
Stamp
Location
Lock Side UniroseLatch Side Unirose
Spacer Locations
Part #:LPUXAY2D © Copyright 2017, Universal Industrial Products, Inc.
SOSS®
Door Hardware
Re-assemble the Stops
Using the 1/16" (1.59 mm) hex bit
re -assemble the stops into the order
shown in the illustration.
UltraLatch® is made in the U.S.A. of domestic and imported components.
Universal Industrial Products, Inc.
One Coreway Drive
Pioneer, OH, USA 43554-0628
Phone: (419) 737-2324 (800) 922-6957
FAX: (419) 737-2130
2
5
Note
To switch to a right hand out swing application,
simply rotate the chassis 180 degrees and assemble
to the latch side unirose (part # LP22ALN or # LP22ALE)
as shown in the diagram.
6Re-assemble Chassis to Latch Side Unirose
(Part # LP22ALN or # LP22ALE)
Using the #2 square drive or #2 phillips screwdriver
re-assemble the chassis to the latch side unirose as
shown in the diagram.
If this is a 2” door installation (L3) then you must
also reinstall the spacers between the Chassis and
Unirose at the 2 and 8 o’clock positions.
Lock Side UniroseLatch Side Unirose
Stop Part # LPBAA4
2-Hole Retainer
Stop Part # LPBAA3
3-Hole Retainer
Spacer Locations
Fasten Here
Screw at
8 O’clock
Spacer for
2” Doors Only
Spacer for
2”
Doors Only
Chassis faces
3 O’clock P
osition
Unirose Set Up for
Right Hand Door (Chassis Rotated 180°)
Screw at
2 O’clock
Part #
Stamp
Location
Other Soss Door Lock manuals
