Sony CBK-MB01 User manual

PICTURE CACHE BOARD

CBK-MB01

INSTALLATION MANUAL

1st Edition

CBK-MB01

!WARNING

This manual is intended for qualified service personnel only.

To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that

contained in the operating instructions unless you are qualified to do so. Refer all servicing to

qualified service personnel.

!WARNUNG

Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.

Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die

Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei

Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben

Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung

dazu besitzen.

!AVERTISSEMENT

Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin

de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les

réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.

Pour toute réparation faire appel à une personne compétente uniquement.

1-1 (E)

CBK-MB01

Section 1

Installation

1-1. CBK-MB01 Configuration

The CBK-MB01 consists of the following:

.MY-113 board (1)

.Precision screws P1.4 x3.5 (2)

.Installation Guide (1)

.Installation Manual (1)

In addition to the Installation Manual, the following manuals are available.

.DVW-970/970P Operation Manual (Supplied with DVW-970/970P)

This manual is necessary for application and operation of DVW-970/970P.

.CBK-MB01 Maintenance Manual

This manual intended for use by trained system and service engineers describes the information (Block

diagrams, schematic diagrams, Parts list and etc.) required for parts-level service.

For obtaining, contact your local Sony Sales Office/Service Center.

Part number: 9-968-182-0X

1-2. Installation Procedure

Outline of the installing the CBK-MB01 to the DVW-970/970P is listed as follows. For the details of the

installation work, refer to the respective sections.

When removing or installing the plug-in board, be careful not to damage the parts on circuit board, not to

insert the boards in the wrong slot and not to insert the boards in wrong directions.

Installation procedure Sections describing the detailed procedure

1. Opening the Inside Panel 1-3. Opening and Closing the Inside Panel Assembly

2. Removing the DCP Board Assembly 1-4. Removing and Installing the DCP Board Assembly

3. Removing the DVP Board Assembly 1-5. Removing and Installing the DVP Board Assembly

4. Installing the CBK-MB01 (MY-113 Board) 1-6. Installing the CBK-MB01 (MY-113 Board)

5. Installing the DVP Board Assembly 1-5. Removing and Installing the DVP Board Assembly

6. Installing the DCP Board Assembly 1-4. Removing and Installing the DCP Board Assembly

7. Closing the Inside Panel 1-3. Opening and Closing the Inside Panel Assembly

8. Operation Check 3-2-5. Starting a Shoot with a Few Seconds of Pre-Stored

Check that the cache rec function works correctly Picture Data (Picture Cache Function: with CBK-MB01)

(Refer to the DVW-970/970P Operation Manual)

1-2 (E) CBK-MB01

1-3. Opening and Closing the Inside Panel Assembly

1-3. Opening and Closing the Inside

Panel Assembly

Opening

Be sure to set the POWER switch to OFF, unplug the

power cord or remove the battery before starting any of the

following procedure to protect inside of the unit from

damage.

1. Loosen the four screws (with drop-safe) and open the

inside panel assembly in the direction of the arrow.

.The flexible card wire that is connected to the FP-

148 board, will be significantly shortened of its life

if it is folded. Be very careful not to fold the flexible

card wire.

.Stand the unit in the posture that the POWER switch

side faces upward when the inside panel assembly is

opened.

Closing

1. Check that the hinges in the right and left are engaged

securely with the hooks of the chassis.

2. Insert the inside panel assembly and tighten the four

screws (with drop-safe).

Standard tightening torque :

Screw (with drop-safe, B3 x12)

0.8 N.m (8.0 kgf.cm)

Be careful not to pinch the harness between the inside

panel assembly and the chassis.

FP-148 board

Flexible card wire

POWER switch

Inside panel

assembly

Inside panel

assembly

Hook

Hinge

Screws

(with drop-safe)

Screws

(with drop-safe)

Screws

(with drop-safe)

1-3 (E)

CBK-MB01

1-4. Removing and Installing the DCP Board Assembly

1-4. Removing and Installing the DCP

Board Assembly

Removal

Open the inside panel assembly. (Refer to Section 1-3.)

2. Disconnect the coaxial cable from the connector

(CN10) of the DCP-38 board. (When the CBK-SD01

is installed, disconnect the coaxial cable from the

connector (CN1) of the DIF-147 board.)

To disconnect the coaxial cable, do not attempt to

disconnect it by pulling the coaxial cable with force.

Be sure to hold the plug and disconnect the cable.

3. Remove the screw (B2.6 x5) and the filter cover.

4. Disconnect the board-to-board connector that comes

from the DCP-38 board, and open the CN-2437 board

in the direction of the arrow.

B2.6 x5

Coaxial cable

CN-2437

board

DCP-38

board

CN10

CN-2437 board Board to

board connector

DCP-38 board

Hold the plug

to remove

Do not attempt to

remove by pulling

the plug.

Filter cover

5. Remove the harnesses from the connectors (CN1, CN3

and CN4) of the VA-228 board.

6. Remove the two screws (B2.6 x5).

7. Open the board lever in the direction of arrow A, and

disconnect the board-to-board connector that is

connected to the MB-1032 board.

8. Raise the DCP board assembly about 10 mm in the

direction of arrow B, and align the recessed portion of

the DCP-38 board with the protruded portion of the

board holder.

CN4

CN3

CN1

B2.6 x 5

VA-228 board

Harness

MB-1032 board

DCP board assembly

DCP board

assembly

Recessed

portion

Board-to-board

connector

Board holder

Board

holder

Board lever

1-4 (E) CBK-MB01

1-4. Removing and Installing the DCP Board Assembly

9. Slant the DCP board assembly to the front and remove

it.

Reinstallation

1. Reinstall the DCP board assembly by reversing the

steps 4 to 9 of removal.

.Route the harnesses coming from the connectors

(CN1, CN3 and CN4) of the VA-228 board so that

they do not jump out of the surface (the surface

shown by the arrow) on the VA-228 board.

.Route the harnesses so that it is positioned in the

recessed portion of the DCP-38 board.

DCP board assembly

CN4

CN3

CN1

VA-228 board

Harness

Harness (MA)

Recess of

the DCP-38 board

DCP-38 board

2. Continue reinstallation of the DCP board assembly by

reversing the steps 2 to 3 of removal.

.When installing the filter cover, route the harness

(MA) connected from the CN-2437 board to the SE-

803 board so that it passes near the screw that

secures the upper end of the DCP-38 board. At that

time, ensure that the harness (MA) passes between

the guides at the upper right and left of the filter

cover.

.After the CN-2437 board is reinstalled, rotate the

filter knob in both directions to confirm that it is not

caught by the harness (MA).

.Be careful that the harness must not be pitched

between the inside panel and the chassis.

3. Close the inside panel. (Refer to Section 1-3.)

Tightening torque :

Removal step 6, DCP board assembly (B2.6 screw): 53 x

10-2 ±0.01 N.m (5.3 ±0.1 kgf.cm)

Filter cover

upper guides Screw

DCP-38 board

Harness (MA)

SE-803 board

Filter cover

Filter Knob

1-5 (E)

CBK-MB01

1-5. Removing and Installing the DVP Board Assembly

1-5. Removing and Installing the DVP

Board Assembly

Removal

Open the inside panel assembly. (Refer to Section 1-3.)

Remove the DCP board assembly. (Refer to Section 1-4.)

3. Disconnect the flexible card wire from the EQ-88

board connector (CN101).

.Life of flexible card wire will be significantly

shortened if it is folded. Be very careful not to fold

the flexible card wire.

.If the copper plating of the base material exposes

due to wear of the tin plated contact of the connec-

tor, replace it with the new flexible card wire.

CN101

EQ-88 boardFlexible card wire

4. Open the board lever in the direction of arrow A and

remove the board-to-board connector that is connected

to the MB-1032 board.

5. Raise the DVP board assembly in the direction of arrow

B by about 15 mm and align the protruded portion of the

board holder (F) with the recessed portion of the DVP-

34 board.

Slant the DVP board assembly to the front and remove it.

MB-1032 board

DVP board

assembly

Board lever

Board-to-board

connectors

Recessed

portion of

the DVP

board

assembly

Protruded

portion of

the board

holder (F)

DVP board

assembly

1-6 (E) CBK-MB01

DVP-34 board

DVP board assembly

CN101

CBK-MB01

Precision screw

P1.4 x3.5

Precision screw

P1.4 x3.5

1-6. Installing the CBK-MB01

(MY-113 Board)

Install the CBK-MB01 to the side-A of the DVP-34 board.

Installation Procedure

1. Insert the connector (CN101) of the CBK-MB01 (MY-

113 board) into the connector (CN101) on the DVP-34

board firmly.

2. Attach the CBK-MB01 with the two precision screws

(P1.4 x3.5) supplied.

Standard tightening torque value :

12 x10_2N.m (1.2 kgf.cm)

1-5. Removing and Installing the DVP Board Assembly

1-6. Installing the CBK-MB01 (MY-113 Board)

Reinstallation

1. Raise the board lever to its upright position.

2. Insert the DVP board assembly in a slant angle until

the protruded portion of the PC board holder (F) meets

the recessed portion of the DVP-34 board. At the

above angle, raise

the DVP board assembly in the right

angle and insert it.

3. When shaft of the board lever enters into the chassis,

slant the board lever and push down the board from its

top until it is firmly inserted to the board-to-board

connector of the MB-1032 board.

4. Reinstall it by reversing the steps of disassembling.

CBK-MB01

The material contained in this manual consists of

information that is the property of Sony Corporation.

Sony Corporation expressly prohibits the duplication of

any portion of this manual or the use thereof for any

purpose other than the operation or maintenance of the

equipment described in this manual without the express

written permission of Sony Corporation.

Le matériel contenu dans ce manuel consiste en

informations qui sont la propriété de Sony Corporation.

Sony Corporation interdit formellement la copie de

quelque partie que ce soit de ce manuel ou son emploi

pour tout autre but que des opérations ou entretiens de

l’équipement à moins d’une permission écrite de Sony

Corporation.

Das in dieser Anleitung enthaltene Material besteht aus

Informationen, die Eigentum der Sony Corporation sind.

Die Sony Corporation untersagt ausdrücklich die

Vervielfältigung jeglicher Teile dieser Anleitung oder den

Gebrauch derselben für irgendeinen anderen Zweck als

die Bedienung oder Wartung der in dieser Anleitung

beschriebenen Ausrüstung ohne ausdrückliche

schriftliche Erlaubnis der Sony Corporation.

Printed in Japan

Sony Corporation 2005. 5 16

CBK-MB01 (SY) J, E

3-872-340-01

Table of contents

Other Sony Camera Accessories manuals

Sony

Sony HDVF-550 User manual

Sony

Sony XC-55 User manual

Sony

Sony BVF-20W User manual

Sony

Sony PDWU2 User manual

Sony

Sony CSS-PHB - Cybershot Station For DSCP200 Digital... User manual

Sony

Sony NP-F330 Operating Instructions (primary... Service manual

Sony

Sony IPT-DS1 - Party-shot Digital Camera Docking... User manual

Sony

Sony HVL-RLA User manual

Sony

Sony CBK-3620XS User manual

Sony

Sony VAD-S70 User manual

Sony

Sony MPK-WB User manual

Sony

Sony RM-LVR3 User guide

Sony

Sony Cyber-shot Sports Pack SPK-THA User manual

Sony

Sony APK-THA User manual

Sony

Sony XDCAM PDW-HR1 How to use

Sony

Sony HVL-20DW2 User manual

Sony

Sony VF MPTH2 User manual

Sony

Sony HD Super Motion HKCU1001 User manual

Sony

Sony MPK-PHB User manual

Sony

Sony APK-WB Operating Instructions - Precautions User manual

Sony

Sony HVL-20DW2 User manual

Sony

Sony HKC-T1500 User manual

Sony

Sony HDCU-3300R User manual

Sony

Sony BRS-200 User manual

Popular Camera Accessories manuals by other brands

Viltrox

Viltrox EF-NEX Mount instructions

Calumet

Calumet 7100 Series CK7114 operating instructions

Ropox

Ropox 4Single Series User manual and installation instructions

Cambo

Cambo Wide DS Digital Series Main operating instructions

Samsung

Samsung SHG-120 Specification sheet

Ryobi

Ryobi BPL-1820 Owner's operating manual

Aegis

Aegis ABL-36020P user manual

Pentax

Pentax Data Back Fc operating manual

Fantasea

Fantasea EyeGrabber F Series instruction manual

Honeywell

Honeywell HDZ20HD user manual

EGO

EGO BA1400T Operator's manual

Sima

Sima SRW-62 user guide

Shape

Shape A7SSMKIT Assembly manual

Slide Kamera

Slide Kamera HST-2 user manual

Power works

Power works 2902613 Original instructions

SES

SES SE-2047-2 user manual

Olympus

Olympus PT-EP05L instruction manual

Starlite

Starlite OctoDome nxt instructions