SolarEdge SE2200 User manual

Installation Guide

SolarEdge System

Installation Guide

For Europe and APAC

Version 4.1

Disclaimers

Important Notice

No part of this document may be reproduced, stored in a retrieval system or

transmitted, in any form or by any means, electronic, mechanical, photographic,

magnetic or otherwise, without the prior written permission of SolarEdge Inc.

The material furnished in this document is believed to be accurate and reliable.

However, SolarEdge assumes no responsibility for the use of this material. SolarEdge

reserves the right to make changes to the material at any time and without notice. You

may refer to the SolarEdge web site (www.solaredge.com) for the most updated version.

All company and brand products and service names are trademarks or registered

trademarks of their respective holders.

Patent marking notice: see http://www.solaredge.com/patent

The general terms and conditions of delivery of SolarEdge shall apply.

The content of these documents is continually reviewed and amended, where

necessary. However, discrepancies cannot be excluded. No guarantee is made for the

completeness of these documents.

The images contained in this document are for illustrative purposes only and may vary

depending on product models.



Disclaimers 1

Three Phase System Installation Guide MAN-01-00057-4.1

Emission Compliance

This equipment has been tested and found to comply with the limits applied by the

local regulations. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, you are encouraged to try to

correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for

compliance may void the user’s authority to operate the equipment.

-Three Phase System Installation Guide MAN-01-00057-4.1

2 Emission Compliance

Support and Contact Information

If you have technical problems concerning SolarEdge products, please contact us:

Country Phone E-Mail

Australia (+61) 1800 465 567 support@solaredge.net.au

APAC (Asia Pacific)(+972) 073 240 3118 support-asia@solaredge.com

Belgium (+32) 0800-76633 support@solaredge.be

China (+86) 21 6212 5536 support_

china@solaredge.com

DACH & Rest of Europe (+49) 089 454 59730 support@solaredge.de

France (+33) 0800 917410 support@solaredge.fr

Italy (+39) 0422 053700 support@solaredge.it

Japan (+81) 03 6262 1223 support@solaredge.jp

Netherlands (+31) 0800-7105 support@solaredge.nl

New Zealand (+64) 0800 144 875 support@solaredge.net.au

Republic of Ireland (+353) 1800-901-575 support-uk@solaredge.com

United Kingdom (+44) 0800 028 1183

US & Canada (+1) 510 498 3200 ussupport@solaredge.com

Greece (+49) 89 454 59730

support@solaredge.com

Israel (+972) 073 240 3122

Middle East &Africa (+972) 073 240 3118

South Africa (+27) 0800 982 659

Turkey (+90) 216 706 1929

Worldwide (+972) 073 240 3118

Before contact, make sure to have the following information at hand:

Model and serial number of the product in question.

The error indicated on the InverterLCD screen or on the monitoring platform or

by the LEDs, if there is such an indication.

System configuration information, including the type and number of modules

connected and the number and length of strings.

The communication method to the SolarEdge server, if the site is connected.

The inverter software version as appears in the ID status screen.

Support and Contact Information 3

Three Phase System Installation Guide MAN-01-00057-4.1

Revision History

Version 4.1 (February 2019)

Added appendix 'Determining the Circuit Breaker Size' and paragraph

referencing to it, in the 'Grid Connection Guidelines' section.

In Specifications removed 'Recommended OCPD size per grid' table.

Version 4.0 (July 2018)

This guide describes three phase inverters only

Update of product names

Removal of grounding cable connected to the DINrail in the DC Safety Unit.

Hardware change - new enclosure, interfaces and communication board

Addition of possibility to use compatible connectors from third-party

manufacturers

Update regarding use of extension cables in power optimizer installation

guidelines

Recommendation to mount the power optimizer in a location protected from

direct sunlight

Power optimizer clearance - no clearance is required on the mounting bracket

side

Addition of caution - installation in saline environment

Clearance for three phase inverters installed side-by-side, single row of inverters

outdoors: 5 cm / 2”

PVRSSis enabled by default. Enabling/ disabling PVRSS feature can be done

from the inverter LCD menus.

Addition of reference to troubleshooting undetected devices application note

Torque for connecting DC strings to the fuse holders in the DC Safety Unit: 3.4

N*M / 30 lb*in

Addition of link to the Designer web page

Updated warning about sealing unused power optimizer input connectors

DC safety voltage is 1V (±0.1V)

-Three Phase System Installation Guide MAN-01-00057-4.1

4 Revision History

Addition of link to Three Phase Inverters for Delta Grids application note

Addition of RS485-2 support

Version 3.3 (Aug.2017)

Updated the Safety section: New warning -The Safety Switch meets all

requirements for a code-compliant installation of this system. The DC

Disconnect Switch disconnects both the positive and negative conductors.

In Supported AC Grids, added:Ground connection is required for all grids

In Power Optimizer Installation chapter:

Updated string extension cable length

Added information for connecting multiple modules in parallel to an

optimizer

Removed reference to racking models and their grounding methods

Removed mentioning of tracker

In inverter Installation chapter:

Added note about copper conductors

Removed previous interface panel description and images, and type 1

bracket

In Inverter Interfaces - updated ON/OFFswitch description

Added a caution about not altering the DC Safety Unit

enclosure:SolarEdge does not permit opening or puncturing the Safety

Switch in any location other than the pre-defined drill guide locations,

or otherwise altering the construction of the enclosure, as this may

compromise safety and will void the warranty.

Reference to horizontal mounting application note

Updated clearance specifications

Connection to/from the Connection Unit:

AC grounding to bus bar instead of terminal block - updated

instructions and Connection Unit model images

String fusing requirement note updated:Fuses needed for 4 strings or

more (instead of 3).

Added conduit sealing requirement

Revision History 5

Three Phase System Installation Guide MAN-01-00057-4.1

In Commissioning chapter:

Updated the activation sequence

Updated menu information descriptions

Removed RS232 reference

In Configuration Menu Options:

Communication section:

Removed RS232 Conf

Added GSMConf

Power Control section:

Removed Phase Balance link and info

Add link to P(Q) diagram application note

Maintenance section:

Added links to application notes (Upgrading the inverter using

SD card; Isolation fault troubleshooting; Arc fault detection)

Removed Optimizer Conf

Status Screens updates:

Meter status screen - added Power and Energy lines

Telemetry status screen - updated

GSMstatus screen - new

Communication options - updated

Inverter cover removal sequence - updated

RS485-E option - new

Added link to Arc Detection application note

Troubleshooting:

Error codes moved to a separate document. A link was added to the

manual.

Slave Detect and Slave List - updated

Mechanical specifications - removed type 1 bracket

External fan replacement - updated

Updated the technical specification document

-Three Phase System Installation Guide MAN-01-00057-4.1

6 Revision History

Explained whichoptimizerinstallation steps to skip when using smart modules.

Added RS485 slave detect feature

Removed USB

Revision History 7

Three Phase System Installation Guide MAN-01-00057-4.1

Contents

Disclaimers 1

Important Notice 1

Emission Compliance 2

Support and Contact Information 3

Revision History 4

HANDLING AND SAFETY INSTRUCTIONS 10

Safety Symbols Information 10

IMPORTANTSAFETYINSTRUCTIONS 11

Chapter 1: Introducing the SolarEdge Power Harvesting System 13

Power Optimizer 13

Inverter 14

Monitoring Platform 14

Installation Procedure 14

Installation Equipment List 14

Inverter Transport and Storage 15

Chapter 2: Installing the Power Optimizers 16

Safety 16

Installation Guidelines 17

Step 1: Mounting the Power Optimizers 20

Step 2: Connecting a PV Module to a Power Optimizer 20

Step 3: Connecting Power Optimizers in Strings 21

Step 4: Verifying Proper Power Optimizer Connection 22

Chapter 3: Installing the Inverter 23

Inverter Package Contents 23

Identifying the Inverter 23

Inverter Interfaces 23

Mounting the Inverter 26

Chapter 4: Connecting the AC and the Strings to the Inverter 31

Grid Connection Guidelines 31

Connecting the ACGrid to the Inverter 32

Connecting the Strings to the Inverter 34

Selecting a Residual Current Device (RCD) 34

Chapter 5: Commissioning the Installation 36

Step 1: Activating the System 36

Step 2: Pairing Power Optimizers to the Inverter 38

Step 3: Verifying Proper Activation 40

Step 4: Reporting and Monitoring Installation Data 40

Chapter 6: User Interface 44

-Three Phase System Installation Guide MAN-01-00057-4.1

8 Revision History

LCD User Buttons 44

Inverter Configuration – Setup Mode 46

Configuration Menu Options 50

Status Screens - Operational Mode 57

Chapter 7: Setting Up Communication 66

Communication Options 66

Communication Connectors 69

Removing the Inverter Cover 70

Creating an Ethernet (LAN) Connection 70

Creating an RS485 Bus Connection 74

Verifying the Connection 78

Appendix A: Errors and Troubleshooting 80

Troubleshooting Communication 80

Power Optimizer Troubleshooting 82

Appendix B: Mechanical Specifications 84

Appendix C: Connecting the AC and DCStrings to the DC Safety Unit 85

Connecting the ACGrid to the Inverter 86

Connecting the Strings to the DC Safety Unit 87

Appendix D: SafeDC™ 90

Appendix E: External Fan Maintenance and Replacement 91

Fan Maintenance 91

External Fan Replacement 91

Appendix F: Replacing and Adding System Components 93

Replacing an Inverter 93

Replacing the DC Safety Unit 94

Adding, Removing, or Replacing Power Optimizers 97

Appendix G: Determining the Circuit Breaker Size 98

Revision History 98

Introduction 98

Using Transformers in Commercial Three Phase Inverter Installations 98

Determining the Size of an Inverter Circuit Breaker 100

Technical Specifications - Single Phase Inverters (Europe &APAC) 102

Technical Specifications - Three Phase Inverters (Europe &APAC) 105

Revision History 9

Three Phase System Installation Guide MAN-01-00057-4.1

This manual suits for next models

Table of contents

Other SolarEdge Inverter manuals

SolarEdge

SolarEdge SE K Series User manual

SolarEdge

SolarEdge SE66.6KUS User manual

SolarEdge

SolarEdge EV Series User manual

SolarEdge

SolarEdge SE330K User manual

SolarEdge

SolarEdge StorEdge Interface SESTI-S4 User manual

SolarEdge

SolarEdge Power Optimizer User manual

SolarEdge

SolarEdge SEXXXXH-RWMBNBF54 User manual

SolarEdge

SolarEdge SE15K-AU User manual

SolarEdge

SolarEdge SE3000H-US User manual

SolarEdge

SolarEdge SE2500H User manual

SolarEdge

SolarEdge SE7600A-US User manual

SolarEdge

SolarEdge SE8k User manual

SolarEdge

SolarEdge 3000A-US User manual

SolarEdge

SolarEdge SE K Series User manual

SolarEdge

SolarEdge storedge User manual

SolarEdge

SolarEdge StorEdge SE7600A-USS User manual

SolarEdge

SolarEdge P300 User manual

SolarEdge

SolarEdge SE Series User manual

SolarEdge

SolarEdge SE50K User manual

SolarEdge

SolarEdge SE8K-N4 User manual

SolarEdge

SolarEdge SE9KUS User manual

SolarEdge

SolarEdge SE3K-RWB User manual

SolarEdge

SolarEdge 330kW User manual

SolarEdge

SolarEdge SE12.5k User manual

Popular Inverter manuals by other brands

Fourgroup

Fourgroup Easy use and Programming Handbook

Velleman

Velleman PI300M user manual

Sungrow

Sungrow SG350HX-US user manual

WilTec

WilTec 61897 Operation manual

SMA

SMA SUNNY BOY STORAGE 2.5 Quick reference guide

Simplicity

Simplicity LANDLORD 316 product manual

Santak

Santak SMAX 3000 user manual

ATON

ATON RA.Store-3 user manual

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ operating instructions

Tektronix

Tektronix CFG250 Operator's manual

Champion

Champion 200989 Operator's manual

Vanner

Vanner 20-500 Series owner's manual

GE GEP user manual

Astrel Group

Astrel Group Power Reducer Installation and instruction manual

MULTIQUIP

MULTIQUIP GDP-5H Operation and parts manual

GoWISE

GoWISE PS1007 user manual

Promate

Promate PM13500D ES Operator's manual

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM user manual