SolarEdge Energy Bank User manual

Installation Guide

Single Phase Energy Hub

Inverter

with Prism Technology

For Australia

Version 1.1

Disclaimers

Important Notice

No part of this document may be reproduced, stored in a retrieval system or

transmitted, in any form or by any means, electronic, mechanical, photographic,

magnetic or otherwise, without the prior written permission of SolarEdge Inc.

The material furnished in this document is believed to be accurate and reliable.

However, SolarEdge assumes no responsibility for the use of this material. SolarEdge

reserves the right to make changes to the material at any time and without notice. You

may refer to the SolarEdge web site (www.solaredge.com) for the most updated version.

All company and brand products and service names are trademarks or registered

trademarks of their respective holders.

Patent marking notice: see http://www.solaredge.com/patent

The general terms and conditions of delivery of SolarEdge shall apply.

The content of these documents is continually reviewed and amended, where

necessary. However, discrepancies cannot be excluded. No guarantee is made for the

completeness of these documents.

The images contained in this document are for illustrative purposes only and may vary

depending on product models.

Disclaimers 1

Single Phase Energy Hub Inverter MAN-01-00812-1.1

Emission Compliance

This equipment has been tested and found to comply with the limits applied by the

local regulations.

These limits are designed to provide reasonable protection against harmful interference.

This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off

and on, you are encouraged to try to correct the interference by one or more of the

following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for

compliance may void the user’s authority to operate the equipment.

Single Phase Energy Hub Inverter MAN-01-00812-1.1

2 Emission Compliance

Revision History

Version 1.1 (August 2021)

Added support of SolarEdge Energy Bank and LG RESUPrime batteries.

Version 1.0 (January 2021)

First release of this guide

Revision History 3

Single Phase Energy Hub Inverter MAN-01-00812-1.1

Contents

Disclaimers 1

Important Notice 1

Emission Compliance 2

Revision History 3

HANDLING AND SAFETY INSTRUCTIONS 6

Safety Symbols Information 6

IMPORTANTSAFETYINSTRUCTIONS 7

Chapter 1: Overview 10

StorEdge Solution Components 10

Installation Equipment List 12

Inverter Transport and Storage 13

Chapter 2: Installing the Power Optimisers 14

Safety 14

Installation Guidelines 16

Step 1: Mounting the Power Optimisers 18

Step 2: Connecting a PV module to a Power Optimiser 18

Step 3: Connecting Power Optimizers in Strings 19

Step 4: Verifying Proper Power Optimiser Connection 20

Chapter 3: Installing the Inverter 21

Inverter Package Contents 21

Identifying the Inverter 21

Inverter Interfaces 21

Mounting the Inverter 25

Selecting a Residual Current Device (RCD) 28

Chapter 4: Installing the Battery (Optional) 30

Chapter 5: Connecting the Inverter 31

Installing Conduits 31

Connecting the Inverter to ACGrid 32

Connecting the DC Strings to the Inverter 32

Connecting the Battery (Optional) 34

Connecting the Backup Interface (Optional) 36

Connecting an External CTto the Energy Meter (Optional) 36

Installing the 9V Battery 37

Connecting Multiple Inverters through RS485 38

Chapter 6: Activating, Commissioning and Configuring the System 40

Step 1: Activating the Installation 40

Step 2: Commissioning and Configuring the Installation 41

Step 3: Verifying Proper Activation and Commissioning 43

Single Phase Energy Hub Inverter MAN-01-00812-1.1

4 Revision History

Configuring Communication with Other Devices 43

Running a Battery Self-test 44

Enabling StorEdge Applications 45

Reporting and Monitoring Installation Data 46

Chapter 7: Setting Up Communication with the Monitoring Platform 49

Communication Options 49

Communication Connectors 50

Removing the Inverter Cover 51

Removing the Connection Unit Cover (if applicable) 51

Creating an Ethernet (LAN) Connection 52

Verifying the Connection 54

Appendix A: Errors and Troubleshooting 55

Identifying Errors 55

Energy Hub Inverter Troubleshooting 56

Troubleshooting Communication 57

Power Optimiser Troubleshooting 58

Appendix B: SafeDC™ 61

Single Phase Energy Hub Inverter - Technical Specifications 62

Support Contact Information 66

Revision History 5

Single Phase Energy Hub Inverter MAN-01-00812-1.1

HANDLING AND SAFETY INSTRUCTIONS

Safety Symbols Information

The following safety symbols are used in this document. Familiarize yourself with the

symbols and their meaning before installing or operating the system.

WARNING!

Denotes a hazard. It calls attention to a procedure that, if not correctly

performed or adhered to, could result in injury or loss of life. Do not proceed

beyond a warning note until the indicated conditions are fully understood and

met.

CAUTION!

Denotes a hazard. It calls attention to a procedure that, if not correctly

performed or adhered to, could result in damage or destruction of the

product. Do not proceed beyond a caution sign until the indicated conditions

are fully understood and met.

NOTE

Denotes additional information about the current subject.

IMPORTANTSAFETYFEATURE

Denotes information about safety issues.

Disposal requirements under the Waste Electrical and Electronic Equipment (WEEE)

regulations:

NOTE

Discard this product according to local regulations or send it back to SolarEdge.

Single Phase Energy Hub Inverter MAN-01-00812-1.1

6 HANDLING AND SAFETY INSTRUCTIONS

IMPORTANTSAFETYINSTRUCTIONS

SAVETHESEINSTRUCTIONS

Warning!

To reduce the risk of injury, read all instructions in this document.

WARNING!

The inverter cover must be opened only after switching the inverter ON/OFF/P

switch located at the bottom of the inverter to OFF. This disables the DC voltage

inside the inverter. Wait five minutes before opening the cover. Otherwise, there

is a risk of electric shock from energy stored in the capacitors.

WARNING!

Before operating the inverter, ensure that the inverter AC power cable and wall

outlet are grounded properly. This product must be connected to a grounded,

metal, permanent wiring system, or an equipment-grounding conductor must

be run with the circuit conductors and connected to the equipment grounding

terminal or lead on the product.

WARNING!

Opening the inverter and repairing or testing under power must be performed

only by qualified service personnel familiar with this inverter.

WARNING!

Do not touch the PV panels or any rail system connected when the inverter

switch is ON, unless grounded.

WARNING!

SafeDC complies with IEC60947-3 when installing the system with a worst case

SafeDC voltage (under fault conditions) < 120V.

The worst case voltage is defined as: Voc,max+ (String Length-1)*1V, where:

Voc,max = Maximum Voc (at lowest temperature) of the PV modules in the

string (for a string with multiple modules, use the max value)

String Length = number of power optimisers in the string

CAUTION!

This unit must be operated according to the technical specification datasheet

provided with the unit.

CAUTION!

HEAVY OBJECT. To avoid muscle strain or back injury, use proper lifting

techniques, and if required - a lifting aid.

IMPORTANTSAFETYINSTRUCTIONS 7

Single Phase Energy Hub Inverter MAN-01-00812-1.1

NOTE

The Connection Unit is NEMAtype 3R rated . Unused glands should be sealed

with appropriate seals.

NOTE

Use PV modules rated according to IEC 61730 class A.

NOTE

The symbol appears at grounding points on the SolarEdge equipment. This

symbol is also used in this manual.

NOTE

SolarEdge inverters can be installed in sites with an alternative power source

such as a generator. SolarEdge requires installing a physical or electronic

interlock, which will signal to the inverter when the grid has been

disconnected. Interlock procurement, installation, maintenance and support

are the responsibility of the installer. Damage to the inverter due to incorrect

interlock installation or use of an interlock that is incompatible with the

SolarEdge system will render the SolarEdge warranty invalid.

For more information on connecting an alternative power source

to SolarEdge inverter, refer to

https://www.solaredge.com/sites/default/files/se-inverter-

support-of-voltage-sources.pdf.

NOTE

The following warning symbols appear on the inverter warning label:

Risk of electric shock

Risk of electric shock from energy stored in the capacitor. Do

not remove cover until 5 minutes after disconnecting all

sources of supply.

Hot surface – To reduce the risk of burns, do not touch.

Caution, risk of danger

WARNING!

Before operating the system, ensure that the been grounded properly.

Single Phase Energy Hub Inverter MAN-01-00812-1.1

8 IMPORTANTSAFETYINSTRUCTIONS

WARNING!

When handling the storage system battery, adhere to all manufacturer safety

instructions.

WARNING!

Before connecting the battery to the inverter, make sure the battery is powered

off.



SolarEdge Energy Bank

1. Toggle off the battery ON/OFF/P switch.

2. Turn off the battery circuit breaker.



LG Chem Prime Battery

Turn off the circuit breaker.



CAUTION!

This unit must be operated under the specified operating conditions as

described in the technical specifications supplied with the unit.

NOTE

The batteries must be certified according to local regulations and supported by

the SolarEdge inverter firmware.

NOTE

For battery decommissioning and disposal, follow the manufacturer

requirements and instructions.

NOTE

For inverters with a nameplate up to and including 10kW:

Maximum short circuit peak current: 78.1A

Maximum short circuit current duration (until current stops): 113msec

Maximum 3-cycle short circuit current RMS value: 28.7A



IMPORTANTSAFETYINSTRUCTIONS 9

Single Phase Energy Hub Inverter MAN-01-00812-1.1

Other manuals for Energy Bank

This manual suits for next models

Table of contents

Other SolarEdge Inverter manuals

SolarEdge

SolarEdge Solar Inverter User manual

SolarEdge

SolarEdge storedge User manual

SolarEdge

SolarEdge SE2500H User manual

SolarEdge

SolarEdge SE5000H-AU User manual

SolarEdge

SolarEdge storedge User manual

SolarEdge

SolarEdge StorEdge SE5000-xxS0 series User manual

SolarEdge

SolarEdge SE3000US User manual

SolarEdge

SolarEdge SEK-I Series User manual

SolarEdge

SolarEdge StorEdge SE5K-RWS User manual

SolarEdge

SolarEdge SE2200 User manual

SolarEdge

SolarEdge SE K Series User manual

SolarEdge

SolarEdge SE K Series User manual

SolarEdge

SolarEdge Power Harvesting System User manual

SolarEdge

SolarEdge SE3000 User manual

SolarEdge

SolarEdge StorEdge SE10K-RWS User manual

SolarEdge

SolarEdge SE Series User manual

SolarEdge

SolarEdge SE66.6KUS User manual

SolarEdge

SolarEdge SEXXXXH-RWMBNBF54 User manual

SolarEdge

SolarEdge Inline Energy Meter User manual

SolarEdge

SolarEdge storedge User manual

SolarEdge

SolarEdge StorEdge SE5000H-O4 User manual

SolarEdge

SolarEdge P300 User manual

SolarEdge

SolarEdge Home Battery 48V User manual

SolarEdge

SolarEdge SE K Series User manual

Popular Inverter manuals by other brands

Fourgroup

Fourgroup Easy use and Programming Handbook

Velleman

Velleman PI300M user manual

Sungrow

Sungrow SG350HX-US user manual

WilTec

WilTec 61897 Operation manual

SMA

SMA SUNNY BOY STORAGE 2.5 Quick reference guide

Simplicity

Simplicity LANDLORD 316 product manual

Santak

Santak SMAX 3000 user manual

ATON

ATON RA.Store-3 user manual

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ operating instructions

Tektronix

Tektronix CFG250 Operator's manual

Champion

Champion 200989 Operator's manual

Vanner

Vanner 20-500 Series owner's manual

GE GEP user manual

Astrel Group

Astrel Group Power Reducer Installation and instruction manual

MULTIQUIP

MULTIQUIP GDP-5H Operation and parts manual

GoWISE

GoWISE PS1007 user manual

Promate

Promate PM13500D ES Operator's manual

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM user manual