Smokeeter SE 50 User manual

ELECTRONIC AIR CLEANERS

INSTALLATION AND OPERATION MANUAL

MODEL SE 30

MODEL SE 40

MODEL SE 50

SPECIFICATIONS

POWER REQUIREMENTS

115 VAC, 60 HZ

3.2 Amps (max.)

POWER CONSUMPTION

370 Watts (max.)

AIR HANDLING CAPACITY MODEL SE 30

Low - 150 to 420 CFM*

WEIGHT

Hanging. . . . . . 75 lbs. (34 kg)

Shipping. . . . . . 82 lbs. (37 kg)

DIMENSIONS

Height Width Length

10 7/8"20 1/4"31"

(28 cm) (51 cm) (79 cm)

*CFM is variable

POWER REQUIREMENTS

115 VAC, 60 HZ

6.0 Amps (max.)

POWER CONSUMPTION

690 Watts (max.)

AIR HANDLING CAPACITY MODEL SE 40

Low - 450 to 950 CFM*

WEIGHT

Hanging. . . . . 113 lbs. (51 kg)

Shipping. . . . . 120 lbs. (54 kg)

DIMENSIONS

Height Width Length

12 7/8"21" 40"

(33 cm) (53 cm) (102 cm)

*CFM is variable

POWER REQUIREMENTS

115 VAC, 60 HZ

7.0 Amps (max.)

POWER CONSUMPTION

800 Watts (max.)

AIR HANDLING CAPACITY MODEL SE 50

High speed tap - 1,060 to 1,500 CFM*

Low speed tap - 590 to 1,300 CFM*

WEIGHT

Hanging . . . . . 140 lbs. (63.5 kg)

Shipping . . . . . 151 lbs. (68.5 kg)

DIMENSIONS

Height Width Length

20" 19 1/2"40"

(51 cm) (50 cm) (102 cm)

*CFM is variable

DIMENSIONS

SE 30

SE 40

SE 50

201⁄4"

51 cm

107⁄8"

28 cm

31"

79 cm

40"

102 cm

21"

53 cm

127⁄8"

33 cm

20"

51 cm

191⁄2"

50 cm

40"

102 cm

TABLE OF CONTENTS

SECTION PAGE

I. Introduction 4

II. Inspection of Equipment 4

Ill. How Your Air Cleaner Operates 4

IV. Installation 4

V. Operation 6

VI. Cleaning 6

THE FOLLOWING INFORMATION IS PROVIDED

FOR TRAINED SERVICE PERSONNEL ONLY.

VII. Periodic Maintenance and Troubleshooting 8

VIII. Parts Ordering 10

IX. Illustrated Parts

SE 30 12

SE 40 18

SE 50 24

Wiring Diagrams 30

IMPORTANT NOTICE

BEFORE OPERATION, PLEASE REMOVE ALL PACKING MATERIAL FROM INSIDE

UNIT. THIS CAN INCLUDE MARKED TIE DOWN SCREWS, CARDBOARD,

STYROFOAM AND PLASTIC WRAP ON CARBON FILTER. MODELS VARY IN

MATERIAL USED.

COMPONENTS THAT MAKE IT WORK

PREFILTER traps the larger particles and evenly distributes

the air across the ionizing section to maximize efficiency.

IONIZER is made up of fine tungsten wires supported

between metal plates. When high voltage is applied to

these parts, a “corona” field is generated which imparts

a high-voltage charge on particles that pass through it.

COLLECTION CELL is made up of a series of convoluted

metal plates. These plates act like a magnet and attract

the charged particles removing them from the air. The

plates are alternately charged positive and ground. The

positive plates repel the particles while the ground plates

attract them, yielding a very high efficiency.

NOTE: The SE 40 contains an ionizer and collection cell as

a one piece assembly known as a unicell.

SPEED CONTROL SWITCH allows you to adjust the airflow

between 150 and 420 cubic feet of air per minute (CFM)

on the SE 30 and 450 and 950 CFM on the SE 40. The

switch on the SE 50 allows you to adjust the airflow

between 1,060 and 1,500 CFM on the high speed tap

and between 590 and 1,300 CFM on the low speed tap.

The SE 50 is shipped on high tap.

MOTOR/BLOWER produces air movement by a low

speed, dynamically-balanced, forward-curved blower.

The direct drive motor is thermally protected.

IV. INSTALLATION

NOTE: This product has been designed specifically for

commercial applications, such as offices, night

clubs, bowling centers and bingo halls. United Air

Specialists assumes no responsibility for those

applications unlike the aforementioned.

CAUTION: To reduce the risk of electric shock, this

equipment has a grounding-type plug that has

a third (grounding) pin. This plug will only fit

into a grounding-type power outlet. If the plug

does not fit into the outlet, contact qualified

personnel to install the proper outlet. Do not

alter the plug in any way.

SMOKEETER is designed to draw the contaminated air

through the unit and exhaust clean air back into the

room. The clean air is used to push contaminated air

around the room to the inlet of the unit. Directions of air

patterns and proper placement of the unit should be

established by your local SMOKEETER distributor or by

United Air Specialists, Inc.

The unit can be installed by mounting on a wall or

suspending from the ceiling joists/structure.

I. INTRODUCTION

NOW YOU CAN BREATHE A LOT EASIER...

... you and everyone else who breathe the air cleaned

electronically by SMOKEETER®

. Your new electronic air

cleaner is the most advanced product of its type on the

market today. As you begin its operation, we would like

to remind you of a few important facts.

First, we appreciate your business and because we

appreciate your business, we have manufactured an

electronic air cleaner worthy of your consideration.

SMOKEETER is designed and engineered to rigid

specifications incorporating the latest technological

advances. It is built using the highest grade materials

available. It is subjected to rigorous quality control

checks before it leaves our factory. And, the unit is

backed by a factory warranty as described on the back

cover.

Second, like any piece of precision equipment, your

SMOKEETER unit needs periodic maintenance. Properly

cared for, it will operate at peak efficiency for many

years to come.

Finally, while we hope you never have any problems,

United Air Specialists, Inc. (UAS) is always ready to lend

assistance. We have factory-trained distributors

worldwide. Should you need information or service,

contact your local distributor or Customer Service at

United Air Specialists, Inc., 4440 Creek Road, Cincinnati,

Ohio 45242, 1-800-252-4647, www.uasinc.com.

II. INSPECTION OF EQUIPMENT

Upon receipt of your unit, check for any shipping

damage. A damaged carton indicates that the

equipment may have received rough handling during

shipping that may have caused internal damage.

Notify your delivery carrier and enter a claim

if any damage is found.

Ill. HOW YOUR AIR CLEANER

OPERATES

The motor/blower assembly draws air through an

aluminum mesh filter which removes the larger particles in

the contaminated air. As the particles pass through the

ionizer section, they are given an intense positive charge.

These charged particles are then collected on cell plates.

The clean air is redistributed into the room by adjustable

outlet diffusers.

SE 30

75 lbs.

WALL MOUNTING

Level and securely attach the mounting cleat to the

wall, ensuring given dimension from ceiling to bolt

centerline as shown in Figure 1. Holes provided on wall

mounting cleat are spaced 12", 16" or 24" on center

mounting patterns. Use fasteners and anchoring devices

to ensure support of the SMOKEETER.

Remove the components from the unit to lighten the

weight and facilitate handling.

Attach the mounting cleat to the top back edge of the

unit with two 3/8-16 x 3/4” hex head bolts and washers

that are provided. Install two 3/8-16 x 11

/4” leveling

screws in the bottom outside holes. Refer to Figure 2.

Place the unit on a lifting device. Position the lifting

device under the wall mounting cleat. Raise the unit

into position and engage the wall mounting cleat with

cleat mounted to the unit. Ensure engagement by

visually checking from the end.

Check level and adjust leveling screws as needed.

Mark location on hold-down fastener on the wall.

Hole is located behind the collection cell and marked

with a label.

Remove the unit from mounting and prepare wall for

hold-down fastener.

Reinstall the unit as before and install hold-down

fastener.

The fasteners should now be tested to support the

weight previously mentioned.

Completed installation should be as shown in Figure 3,

with mounting cleat fully engaged, leveling screw in

position and hold-down bolt in wall.

SE 40

113 lbs.

SE 50

138 lbs.

FIGURE 1

WARNING — ATTACH WALL MOUNT TO CLEAT TO WALL

AND TEST LOAD CAPACITY AS SHOWN IN ILLUSTRATION.

FIGURE 2

FIGURE 3

SUSPENSION

Threaded rod, wire or eyebolts and chain may be used

for hanging the unit. Four “knockouts,” located as

shown in Figure 4, must be removed.

It is recommended that a nut on the inside and outside

of the cabinet be used to lock the fastener in place.

Refer to Figure 4.

Test the unit for secure support.

V. OPERATION

For best results and to assure maximum air quality, your

SMOKEETER unit should be started before the air

becomes contaminated. An indicator lamp indicates

that high voltage to the components is on. A variable-

speed control switch allows you to adjust the blower

speed. If you notice a decrease of cleaning

efficiency, increase the blower speed to increase

effectiveness of the unit.

FOR YOUR INFORMATION — The equipment has been

thoroughly tested prior to shipment from the factory.

Even so, there may be some initial arcing of the

components at start-up. The noise should cease after

a few minutes of operation.

VI. CLEANING

CAUTION: Servicing this product for purposes other than

routine cleaning of the collection

components should be performed by

trained authorized service personnel. Any

effort to exceed this service (by non-

qualified personnel) may lead to bodily

injury and/or equipment failure.

This section is defined for cleaning and periodic

maintenance. The internal components must be

removed prior to cleaning.

CAUTION: The unit should be inspected frequently and

dirt removed to prevent excessive

accumulation which may result in flashover

or fire damage. An electrical interlock is

provided for protection — do not defeat its

purpose.

HOW TO REMOVE COMPONENTS

1 . Turn off the unit.

•Open the access door.

•For added safety, manually discharge the

ionizer and collection cell/unicell in the

following manner. Place the blade of a

common screwdriver (with insulated handle)

across the ionizer wire support and then the

ionizer frame. Next, place the screwdriver blade

across the cell end plate and then across a cell

“hot” plate. This will remove any residual

charge that may not have bled off. Refer to

Figure 5.

2. Slide components from the cabinet.

SE 30

SE 40

SE 50

FIGURE 4

CLEANING

Major cleaning is confined to the prefilter, ionizer,

collection cell and the inside cabinet. These should be

cleaned periodically to assure continued efficiency.

Cleaning may be required from once a month to once

every four months depending on the air quality.

NOTE: The carbon filter cannot be cleaned and needs

to be replaced as required.

I . Disconnect power to unit and remove

components.

2. The ionizer, collection cell/unicell and prefilter

can be cleaned by soaking in a hot solution of

SMOKEETER brand detergent for 30 to 60 minutes.

If possible, agitate the solution to aid in dirt

removal. If agitation is not possible, soaking time

should be increased.

CAUTION: Do not use temperature exceeding 160°F

and do not steam clean as this may cause

permanent damage to the components. If

detergent other than SMOKEETER brand is

used, care must be taken to assure that it

contains an aluminum inhibitor so that it

does not attack the aluminum components.

Be sure to follow manufacturer’s cleaning

instructions.

3. Remove the components from the detergent

bath and immediately flush away any residue and

rinse thoroughly with clear hot (less 160°F) water.

Shake off excess water and let components dry

for 30 to 60 minutes. Set the cell so that its plates

are in a vertical position for drainage.

4. Vacuum clean the interior of the cabinet and

clean off all electrical connections before

reinstalling the components.

5. Reinstall the components into the cabinet.

6. Apply power to unit and confirm indicator light is

illuminated.

SE 30

SE 40

NOTE: The SE 40 contains an ionizer and collection cell

as a one piece assembly known as a unicell.

FIGURE 5

VIl. PERIODIC MAINTENANCE AND

TROUBLESHOOTING

The following sections are for the use of trained

service personnel only.

WARNING — THE FOLLOWING PROCEDURES WILL

EXPOSE HAZARDOUS LIVE AND MOVING PARTS.

DISCONNECT AIR CLEANER BEFORE PROCEEDING.

All SMOKEETER air cleaners are manufactured to

give years of trouble-free performance. As with

any piece of equipment, however, breakdowns

can occur. Due to the simplicity of design,

breakdowns are restricted to these components:

•the motor/blower*

•the power pack

•ionizer

•collection cell/unicell

•blower control switch

•safety switch

•indicator lamp

This section covers the troubleshooting procedure

and a table which will enable you to determine the

cause of most problems. Refer to Section VIII for

replacement parts.

*These models are equipped with permanently

lubricated motors. No further oiling is required.

COMPONENT FUNCTION

1. Power Pack - the electrical circuit is designed

around the power pack which contains the

necessary components to convert 115 Volts,

single-phase, 60 hertz to the high voltage DC

required for the components.

2. Ionizer - the ionizing section supports several

tungsten wires charged positive to a nominal

11,000 volts DC. The baffle plates parallel to the

wire are at ground potential. The ionizer’s function

is to electrically charge the contaminated

particles as they pass through the ionizer.

3. Collection Cell - the collecting section consists of

alternately charged plates. Plates are alternately

charged with a nominal 5,500 volts DC positive.

The field between the plates forces the charged

particles to the ground plates removing them from

the airstream.

NOTE: The SE 40 contains an ionizer and collection cell

as a one piece assembly known as a unicell.

4. Motor/Blower - draws in contaminated air and

exhausts clean air through the outlet.

HOW THE HIGH VOLTAGE IS SUPPLIED TO THE

COMPONENTS

The power pack supplies high voltage DC to the ionizer

and collection cell by the use of high voltage lead

wires. Two separate terminals are used on the output

side of the pack. Terminal #8 supplies nominal 11,000

volts DC positive to the ionizer. Terminal #7 supplies

5,500 volts DC to the cell.

TOOLS REQUIRED FOR TROUBLESHOOTING

•Screwdriver — (common type) 8” or longer with

insulated handle.

•Volt-Ohm Meter — for measuring low voltage

input (115 VAC), continuity (OHMS) and low volt-

age DC.

•High Voltage Probe (DC) positive polarity —

for checking the high voltage power supply

(minimum range from 0 to 15 KV DC).

HOW TO MEASURE HIGH VOLTAGE

To accurately measure the high voltage, a 0 to 15 KV

minimum scale high voltage probe capable of

measuring positive polarity is required.

MEASURING HIGH VOLTAGE

(Refer to Figure 6)

1 . Turn the unit off and open the access door. This

will disengage the safety interlock.

2. Connect the ground clip of the positive polarity

probe to the side of the cabinet.

CAUTION: Always ground the high-voltage probe

to a solid ground connection on the

metal cabinet.

3. Turn unit control switch on and cautiously

engage the safety interlock switch.

CAUTION: Be sure to disengage safety interlock

switch after measuring voltages.

IONIZER VOLTAGE

Place the probe’s tip on the ionizer (refer to

Figure 6) and measure the positive DC voltage.

The voltage should read 10 to 11 KV DC.

•If measurements are abnormal, refer to the trouble-

shooting table (page 11) for cause and correction.

CELL VOLTAGE

Place the probe’s tip on one of the charged plates.

The voltage reading should be 4 to 6 KV DC.

•If measurements are abnormal, refer to the trouble-

shooting table (page 11) for cause and correction.

Table of contents

Other Smokeeter Air Cleaner manuals

Smokeeter

Smokeeter CC User manual

Smokeeter

Smokeeter SE 20 User manual

Smokeeter

Smokeeter SE-40/VARIABLE SPEED User manual

Smokeeter

Smokeeter SE 10 User manual

Popular Air Cleaner manuals by other brands

IKEA

IKEA UPPÅTVIND quick start guide

Nash

Nash AP-1 PureSmart instruction manual

LG PH-U450 Series owner's manual

DeLonghi

DeLonghi DDSX 220WFA manual

Mitsubishi Electric

Mitsubishi Electric MA-E85R-E instruction manual

Sharp

Sharp FU-40SE Operation manual

Philips

Philips AC2721 user manual

Hitachi

Hitachi EP-A3000 instruction manual

TruSens

TruSens Z-2000 manual

Motorola

Motorola MBP87SN quick start guide

Beko

Beko ATP 7100I instruction manual

Carrier

Carrier INFINITY 1620 installation instructions

AtmosAir

AtmosAir P2002 user guide

Winix

Winix NK300 Use & care guide

Friedrich

Friedrich C-90A Service information

Surgically Clean Air

Surgically Clean Air JADE2.0 Operation manual

Base aire

Base aire 555 Pro Installation & operation manual

Champion

Champion CP25 instructions