SMC Networks 8126PL2-F User manual

INSTALLATION GUIDE

TigerSwitchTM 10/100/1000

L2-Lite SMB PoE Gigabit Switch

SMC8126PL2-F

20 Mason

Irvine, CA 92618

Phone: (949) 679-8000

TigerSwitch 10/100/1000

Installation Guide

From SMC's Tiger line of feature-rich workgroup LAN solutions

September 2009

Pub. # 150200000032A

E092009-MW-R01

Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and

reliable. However, no responsibility is assumed by SMC for its use, nor for any

infringements of patents or other rights of third parties which may result from its use. No

license is granted by implication or otherwise under any patent or patent rights of SMC.

SMC reserves the right to change specifications at any time without notice.

SMC Networks, Inc.

20 Mason

Irvine, CA 92618

Trademarks:

SMC is a registered trademark; and EZ Switch, TigerStack and TigerSwitch are

trademarks of SMC Networks, Inc. Other product and company names are trademarks or

registered trademarks of their respective holders.

Warranty and Product Registration

To register SMC products and to review the detailed warranty statement, please refer to

the Support Section of the SMC Website at http://www.smc.com.

Compliances and Safety Warnings

FCC - Class A

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction manual,

may cause harmful interference to radio communications. Operation of this equipment in

a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

You are cautioned that changes or modifications not expressly approved by the party

responsible for compliance could void your authority to operate the equipment.

You may use unshielded twisted-pair (UTP) for RJ-45 connections - Category 3 or better

for 10 Mbps connections, Category 5 or better for 100 Mbps connections, Category 5, 5e,

or 6 for 1000 Mbps connections. For fiber optic connections, you may use 50/125 or 62.5/

125 micron multimode fiber or 9/125 micron single-mode fiber.

Industry Canada - Class A

This digital apparatus does not exceed the Class A limits for radio noise emissions from

digital apparatus as set out in the interference-causing equipment standard entitled

“Digital Apparatus,” ICES-003 of the Department of Communications.

Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux

appareils numériques de Classe A prescrites dans la norme sur le matériel brouilleur:

“Appareils Numériques,” NMB-003 édictée par le ministère des Communications.

CE Mark Declaration of Conformance for EMI and Safety (EEC)

This information technology equipment complies with the requirements of the Council

Directive 89/336/EEC on the Approximation of the laws of the Member States relating to

Electromagnetic Compatibility and 73/23/EEC for electrical equipment used within certain

voltage limits and the Amendment Directive 93/68/EEC. For the evaluation of the

compliance with these Directives, the following standards were applied:

Caution: Do not plug a phone jack connector in the RJ-45 port. This may damage this

device.

Attention: Les raccordeurs ne sont pas utilisés pour le système téléphonique!

RFI Emission: • Limit class A according to EN 55022:1998

• Limit class A for harmonic current emission according to EN 61000-3-2/1995

• Limitation of voltage fluctuation and flicker in low-voltage supply system

according to EN 61000-3-3/1995

Immunity: • Product family standard according to EN 55024:1998

• Electrostatic Discharge according to EN 61000-4-2:1995

(Contact Discharge: ±4 kV, Air Discharge: ±8 kV)

• Radio-frequency electromagnetic field according to EN 61000-4-3:1996

(80 - 1000 MHz with 1 kHz AM 80% Modulation: 3 V/m)

• Electrical fast transient/burst according to EN 61000-4-4:1995 (AC/DC power

supply: ±1 kV, Data/Signal lines: ±0.5 kV)

• Surge immunity test according to EN 61000-4-5:1995

(AC/DC Line to Line: ±1 kV, AC/DC Line to Earth: ±2 kV)

• Immunity to conducted disturbances, Induced by radio-frequency fields:

EN 61000-4-6:1996 (0.15 - 80 MHz with 1 kHz AM 80% Modulation: 3 V/m)

• Power frequency magnetic field immunity test according to

EN 61000-4-8:1993

(1 A/m at frequency 50 Hz)

• Voltage dips, short interruptions and voltage variations immunity test

according to EN 61000-4-11:1994 (>95% Reduction @10 ms, 30%

Reduction @500 ms, >95% Reduction @5000 ms)

LVD: • EN 60950-1:2001

iii

Safety Compliance

Warning: Fiber Optic Port Safety

Avertissment: Ports pour fibres optiques - sécurité sur le plan optique

Warnhinweis: Faseroptikanschlüsse - Optische Sicherheit

Advertencia: Seguridad del puerto de fibra óptica

PSE Alarm

本製品に同梱いたしております電源コードセットは、本製品専用です。本電源コード

セットは、本製品以外の製品並びに他の用途でご使用いただくことは出来ません。

製品本体に同梱された電源コードセットを利用し、他製品の電源コードセットを使用し

ないで下さい。

Power Cord Safety

Please read the following safety information carefully before installing the switch:

WARNING: Installation and removal of the unit must be carried out by qualified personnel

only.

• The unit must be connected to an earthed (grounded) outlet to comply with

international safety standards.

• Do not connect the unit to an A.C. outlet (power supply) without an earth (ground)

connection.

• The appliance coupler (the connector to the unit and not the wall plug) must have

a configuration for mating with an EN 60320/IEC 320 appliance inlet.

• The socket outlet must be near to the unit and easily accessible. You can only

remove power from the unit by disconnecting the power cord from the outlet.

• This unit operates under SELV (Safety Extra Low Voltage) conditions according to

IEC 60950. The conditions are only maintained if the equipment to which it is

connected also operates under SELV conditions.

When using a fiber optic port, never look at the transmit laser while it is

powered on. Also, never look directly at the fiber TX port and fiber cable

ends when they are powered on.

Ne regardez jamais le laser tant qu'il est sous tension. Ne regardez

jamais directement le port TX (Transmission) à fibres optiques et les

embouts de câbles à fibres optiques tant qu'ils sont sous tension.

Niemals ein Übertragungslaser betrachten, während dieses

eingeschaltet ist. Niemals direkt auf den Faser-TX-Anschluß und auf

die Faserkabelenden schauen, während diese eingeschaltet sind.

Cuando utilice un puerto de fibra óptica, nunca mire hacia el láser

de transmisión mientras el mismo esté energizado. Asimismo,

nunca mire directamente hacia el puerto de fibra óptica de

transmisión ni a los extremos del cable de fibra óptica cuando

estén energizados.

CLASS I

LASER DEVICE

DISPOSITIF LASER

DE CLASSE I

LASERGER

DER KLASSE I

ÄT

LASERGER

DER KLASSE I

ÄT

France and Peru only

This unit cannot be powered from IT†supplies. If your supplies are of IT type, this unit

must be powered by 230 V (2P+T) via an isolation transformer ratio 1:1, with the

secondary connection point labelled Neutral, connected directly to earth (ground).

Important! Before making connections, make sure you have the correct cord set. Check

it (read the label on the cable) against the following:

Veuillez lire à fond l'information de la sécurité suivante avant d'installer le Switch:

AVERTISSEMENT: L’installation et la dépose de ce groupe doivent être confiés à un

personnel qualifié.

• Ne branchez pas votre appareil sur une prise secteur (alimentation électrique)

lorsqu'il n'y a pas de connexion de mise à la terre (mise à la masse).

• Vous devez raccorder ce groupe à une sortie mise à la terre (mise à la masse) afin

de respecter les normes internationales de sécurité.

• Le coupleur d’appareil (le connecteur du groupe et non pas la prise murale) doit

respecter une configuration qui permet un branchement sur une entrée d’appareil

EN 60320/IEC 320.

• La prise secteur doit se trouver à proximité de l’appareil et son accès doit être

facile. Vous ne pouvez mettre l’appareil hors circuit qu’en débranchant son cordon

électrique au niveau de cette prise.

Power Cord Set

U.S.A. and Canada The cord set must be UL-approved and CSA certified.

The minimum specifications for the flexible cord are:

- No. 18 AWG - not longer than 2 meters, or 16 AWG.

- Type SV or SJ

- 3-conductor

The cord set must have a rated current capacity of at least 10 A

The attachment plug must be an earth-grounding type with NEMA

5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration.

Denmark The supply plug must comply with Section 107-2-D1, Standard

DK2-1a or DK2-5a.

Switzerland The supply plug must comply with SEV/ASE 1011.

U.K. The supply plug must comply with BS1363 (3-pin 13 A) and be fitted

with a 5 A fuse which complies with BS1362.

The mains cord must be <HAR> or <BASEC> marked and be of type

HO3VVF3GO.75 (minimum).

Europe The supply plug must comply with CEE7/7 (“SCHUKO”).

The mains cord must be <HAR> or <BASEC> marked and be of type

HO3VVF3GO.75 (minimum).

IEC-320 receptacle.

• L’appareil fonctionne à une tension extrêmement basse de sécurité qui est

conforme à la norme IEC 60950. Ces conditions ne sont maintenues que si

l’équipement auquel il est raccordé fonctionne dans les mêmes conditions.

France et Pérou uniquement:

Ce groupe ne peut pas être alimenté par un dispositif à impédance à la terre. Si vos

alimentations sont du type impédance à la terre, ce groupe doit être alimenté par une

tension de 230 V (2 P+T) par le biais d’un transformateur d’isolement à rapport 1:1, avec

un point secondaire de connexion portant l’appellation Neutre et avec raccordement

direct à la terre (masse).

Seguridad del cable de alimentación eléctrica

Antes de instalar el conmutador lea atentamente la siguiente información sobre

seguridad:

• Se debe conectar el equipo a un tomacorriente puesto a tierra (tierra física) para

satisfacer las normas internacionales sobre seguridad.

• No conecte el equipo a un tomacorriente (suministro eléctrico) de CA sin una

conexión de tierra (tierra física).

• El acoplador del dispositivo (el conector que va hacia el equipo y no el enchufe que

va a la pared) deberá tener una configuración que coincida con la de la entrada de

un dispositivo EN 60320/IEC 320.

• El tomacorriente debe estar cerca del equipo y ser fácilmente accesible. Sólo se

puede quitar la alimentación eléctrica al equipo desenchufando el cable de

alimentación eléctrica del tomacorriente.

Cordon électrique - Il doit être agréé dans le pays d’utilisation

Etats-Unis et

Canada:

Le cordon doit avoir reçu l’homologation des UL et un certificat de la

CSA.

Les spécifications minimales pour un cable flexible sont AWG No. 18,

ouAWG No. 16 pour un cable de longueur inférieure à2 mètres.

- type SV ou SJ

- 3 conducteurs

Le cordon doit être en mesure d’acheminer un courant nominal d’au

moins 10 A.

La prise femelle de branchement doit être du type à mise à la terre

(mise à la masse) et respecter la configuration NEMA 5-15P (15 A,

125 V) ou NEMA 6-15P (15 A, 250 V).

Danemark: La prise mâle d’alimentation doit respecter la section 107-2 D1 de la

norme DK2 1a ou DK2 5a.

Suisse: La prise mâle d’alimentation doit respecter la norme SEV/ASE 1011.

Europe La prise secteur doit être conforme aux normes CEE 7/7 (“SCHUKO”)

LE cordon secteur doit porter la mention <HAR> ou <BASEC> et doit

être de type HO3VVF3GO.75 (minimum).

• Este equipo opera bajo las condiciones SELV (Safety Extra Low Voltage o Voltaje

extra bajo de seguridad) de acuerdo con la norma IEC 60950. Las condiciones

sólo se mantienen si la equipo al cual está conectado también opera bajo

condiciones SELV.

Francia y Perú únicamente

Este equipo no puede ser energizado desde suministros IT†. Si su servicio eléctrico es

del tipo IT, este equipo deberá ser alimentado con 230 V (2P+T) a través de un

transformador de aislamiento de relación 1:1, con el punto de conexión del secundario

rotulado Neutro conectado directamente a tierra (tierra física).

¡Importante! Antes de efectuar conexiones, asegúrese de que disponga del conjunto

correcto de cables. Verifíquelo (lea la etiqueta del cable) contra lo siguiente:

Conjunto de cables de alimentación eléctrica

EE.UU. y Canadá El conjunto de cables deberá estar aprobado por UL y certificado por

CSA.

Las especificaciones mínimas del cable flexible son:

- Nº 18 AWG, no mayor de 2 metros, o 16 AWG.

- Tipo SV o SJ

- tres conductores

El conjunto de cables deberá tener una capacidad de corriente

nominal de al menos 10 A.

El enchufe de conexión deberá ser del tipo con puesta a tierra y tener

una configuración NEMA 5-15P (15 A, 125 V) o NEMA 6-15P (15 A,

250 V).

Dinamarca El enchufe de alimentación eléctrica deberá satisfacer la Sección

107-2-D1 de las normas DK2-1a o DK2-5a.

Suiza El enchufe de alimentación eléctrica deberá satisfacer la norma SEV/

ASE 1011.

Reino Unido El enchufe de alimentación eléctrica deberá satisfacer la norma

BS1363 (tres clavijas 13 A) y estar provisto de un fusible de 5 A que

satisfaga la norma BS1362.

El cable de alimentación eléctrica debe estar marcado como <HAR>

o <BASEC> y ser del tipo HO3VVF3GO.75 (mínimo).

Europa El enchufe de alimentación eléctrica deberá satisfacer la norma

CEE7/7 (“SCHUKO”).

El cable de alimentación eléctrica debe estar marcado como <HAR>

o <BASEC> y ser del tipo HO3VVF3GO.75 (mínimo).

Receptáculo IEC-320.

Other manuals for 8126PL2-F

This manual suits for next models

Table of contents

Other SMC Networks Switch manuals

SMC Networks

SMC Networks 8506T User manual

SMC Networks

SMC Networks SMCGS501 - FICHE TECHNIQUE Operating and safety instructions

SMC Networks

SMC Networks D-M9NAV Instruction Manual

SMC Networks

SMC Networks GS1601 Operating and safety instructions

SMC Networks

SMC Networks ZSE30AF-#-#-X576 User manual

SMC Networks

SMC Networks TigerSwitch SMC6624M Programming manual

SMC Networks

SMC Networks TigerSwitch SMC6912M User manual

SMC Networks

SMC Networks 6900FSC - annexe 1 Programming manual

SMC Networks

SMC Networks TigerSwitch SMC6128PL2 User manual

SMC Networks

SMC Networks 8606SX - FICHE TECHNIQUE User manual

SMC Networks

SMC Networks ISE70 AB Series User manual

SMC Networks

SMC Networks 8150L2 User manual

SMC Networks

SMC Networks TigerSwitch 10/100 SMC6750L2 User manual

SMC Networks

SMC Networks SMC6516TF User manual

SMC Networks

SMC Networks 6824MPE INT - FICHE TECHNIQUE Programming manual

SMC Networks

SMC Networks TigerSwitch 100 Programming manual

SMC Networks

SMC Networks ZSE3 Installation manual

SMC Networks

SMC Networks SMC6709GL2 User manual

SMC Networks

SMC Networks TigerStack SMC6924MT User manual

SMC Networks

SMC Networks ISE70G-N02-L2 User manual

SMC Networks

SMC Networks TigerSwitch SMC6709L2 User manual

SMC Networks

SMC Networks EZ Switch SMC-EZ1016DT Owner's manual

SMC Networks

SMC Networks SMC EZ Switch 10/100/1000 SMCGS8P-Smart Programming manual

SMC Networks

SMC Networks 6152PL2 - annexe 1 User manual

Popular Switch manuals by other brands

URC

URC Total Control MFS-8 installation manual

Azbil

Azbil HPQ-D11 user manual

Sony

Sony DFS-900M operating instructions

SICK

SICK i17S operating instructions

F&F

F&F SZR-277 quick start guide

Shure

Shure UAMS/BK user guide

Dräger

Dräger X-zone Switch Off Instructions for use

Asco

Asco Joucomatic 349 Series manual

BT Mini Hub user guide

D-Link

D-Link DES-1226G manual

Johnson Controls

Johnson Controls FS80-C installation instructions

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Configuration guide

MicroNet

MicroNet SP1200A user manual

Ruijie

Ruijie RG-PF2920 Series Hardware installation and reference guide

Altinex

Altinex DA1914SX user guide

MiLAN

MiLAN MIL-SM2401M user guide

RJM

RJM MASTERMIND PBC/6X user manual

Atlas

Atlas MMK-KVM8 owner's manual