SkyScan 87800 User manual

ATOMIC CLOCK

WITH OUTDOOR WIRELESS TEMPERATURE

AND MOON PHASE

MODEL 87800-87801

Instruction Manual

FEATURES:

WWVB Radio controlled time with manual time setting

12/24 hour time display

Time display: hour, minute, second

Alarm setting with snooze function

Calendar display

Weekday display (4 languages to choose from: English, French, Spanish and German)

Time zone setting

Daylight savings time ON/OFF option (DST)

ºC or ºF temperature display selectable

Indoor temperature display

Outdoor temperature display via 433MHz transmission

Wall mount or freestanding

Current moon phase display

Holder

OUTDOOR TEMPERATURE TRANSMITTER:

Remote transmission of outdoor temperature to the atomic clock by 433 MHz

signals

Wall mounting case

TO INSTALL AND REPLACE BATTERIES IN THE ATOMIC CLOCK

The atomic clock uses 2 x AA, 1.5V batteries. To install and replace the batteries, please follow the steps below:

1. Remove the cover.

2. Insert batteries observing the correct polarity (see marking inside battery compartment).

3. Replace compartment cover.

DO NOT SET THE CLOCK.

TO INSTALL AND REPLACE BATTERIES IN THE TEMPERATURE TRANSMITTER

The transmitter uses 2 x AA,1.5V batteries. To install and replace the batteries, please follow the steps below:

1. Remove the cover.

2. Insert the batteries, observing the correct polarity (see marking inside battery compartment).

3. Replace the battery cover on the unit.

Alkaline batteries are recommended for use in both units. Avoid using rechargeable batteries.

SETTING UP:

NOTE: Do not set the clock until the outdoor temperature is displayed.

1. Place batteries in the outdoor transmitter first, then into the atomic clock. DO NOT PRESS ANY

BUTTONS FOR 10 MINUTES.

2. After 10 minutes both the Indoor and Outdoor areas on your clock should have a temperature showing. If

not, remove both sets of batteries, wait 10 minutes and repeat step one.

3. After the clock receives the outdoor temperature, and 10 minutes has elapsed, set your time zone. The

default time zone is Eastern Standard Time (EST). If you live in the Eastern Time zone move to step

4. To set the time zone:

Push and release the “SET” function button.

The time zone (LCD2) will start flashing (Default setting -5EST).

Push the (+) function button to change the default setting (-5EST) to the desired time zone.

-6 CST (Central Time Zone)

-7 MST (Mountain Time Zone)

-8 PST (Pacific Time Zone)

(See “Time Zone Setting” if you live outside the USA)

Weekday

5. After the clock receives the outdoor temperature the WWVB time code reception will automatically start.

The clock will automatically set itself to the exact time, day and date after receipt of the WWVB time code

reception. This typically takes over night. For best reception place your clock next to a window facing

Colorado over night. Once a successful reception is received the Radio Reception ( ) icon will appear

above the blinking colons. Once a successful reception is received relocate your clock to a desired location.

The clock will then automatically attempt to receive the WWVB time from 12:00 am through 6:00 am each

day (attempts WWVB reception every full hour within this time frame). When this is successful, the

received time will override the manually set time. The date is also updated with the received time (Please

refer to notes on “Radio controlled time” and “Manual time setting”).

Note:

In the event of changing batteries of the unit ensure that the batteries do not spring free from the contacts.

Always wait at least 10 minutes after removing the batteries before reinserting, otherwise start up and

transmission problems may occur.

FUNCTION KEYS

The atomic clock has four easy to use keys:

SET key To enter into the set mode for the following functions: time zone, DST ON/OFF (daylight saving

time), language, hour, minute, year, month, day, weekday, 12/24 hour, ºC or ºF temperature display

+key To toggle between the seconds, temperature or weekday display

To change any values in manual set mode

ALM key To enter into the alarm set mode

To set the alarm ON/OFF

SNZ key To activate the snooze function during alarm

To display the alarm time in normal mode display

To exit the setting modes

ATOMIC CLOCK LCD SCREEN DESCRIPTIONS

The atomic clock's LCD is divided into 2 sections. When batteries are inserted, all the segments will light up

briefly before displaying the information for time, date, indoor and outdoor temperatures.

Date

Outdoor temperature display

WWVB time

Time reception icon

Alarm icon

Indoor temperature

MOON PHASE SYMBOLS:

The atomic clock automatically calculates and updates the moon phase diagram on LCD2. The phase display

will change approximately every 2 days, 11 hours. Whenever the date or time is changed manually, the atomic

clock will display the updated moon phase within a few minutes. Twelve stages of the moon’s phases are

represented.

New Moon Small Waxing Large Waxing First Quarter Small Waxing Large Waxing

Crescent Crescent Gibbous Gibbous

FullMoon Large Waning Small Waning Last Quarter Large Waning Small Waning

Gibbous Gibbous Crescent Crescent

Note: The moon phase visible in the sky is noted by a darkening of the LCD screen. Therfore, a full moon is a

complete dark circle.

MANUAL SETTINGS

Note:

If the atomic clock has already successfully received the WWVB time signal and displays the correct time

and date, then the Manual settings can be skipped.

After completion of the above described procedures in “Setting up” the manual setting modes can be entered by

pressing and holding the SET key for 3 seconds. The following settings can now be programmed:

Time zone setting

DST ON/OFF

Language display setting

Manual time setting

Year setting

Month setting

Date setting

Weekday setting

12/24 hour time display setting

ºC or ºF setting

TIME ZONE SETTING

After entering the manual setting mode as described above, the time zone can be set using the number of hours

different from Greenwich Mean Time (GMT) range in LCD2. To do this:

1. The time zone (LCD2) will start flashing (Default setting "-5h“). Select the desired time zone by pressing

and releasing the +key.

Note: The time zones from –4 to –10 hours will be displayed with 3 characters abbreviations:

-4 ATL (Atlantic time),

-5 EST (Eastern time; default time zone),

-6 CST (Central time),

-7 MST (Mountain time),

-8 PST (Pacific time),

-9 ALA (Alaska time),

-10 HAW (Hawaii time).

"GMT” will be displayed if set to GMT (0).

2. Press and release the SET key to enter the “DST Setting“.

DST SETTING (daylight saving time)

1. The ON digit will start flashing on LCD1. Set the DST ON or OFF by pressing the +key.

2. Press and release the SET key to enter the “Language Setting“.

Note:

The DST default is “ON”, meaning that the WWVB will automatically change the time according to Daylight

Saving Time in the spring and fall. For areas that do not recognize DST changes (Arizona and parts of Indiana)

turn the DST “OFF”.

LANGUAGE SETTING

The weekdays can be displayed in LCD2 with the pre-set languages: English, French, Spanish and German.

US = English

F = French

E = Spanish (Espanol)

D = German (Deutsch)

1. Set the desired language for the weekday display in LCD 2 by use of the + key.

2. Press and release the SET key to enter the mode “Manual Time Setting”.

MANUAL TIME SETTING

In case the atomic clock is not able to detect the WWVB-signal (disturbances, transmitting distance, etc.), the

time can be manually set. The clock will then work as a normal Quartz clock.

Note: In 12 hours mode the time will be displayed with an additional “PM”for the time from 12:00 noon until

11:59 pm.

1. The hour digits will start flashing on LCD1.

2. Set the desired hours by pressing and releasing the +key followed by pressing the SET key.

3. Now the minute digits will start flashing.

4. Set the desired minutes by pressing and releasing the +key. If the +key is held, the units will increase by 5.

5. Press and release the SET key to move to the “Year Setting”.

Note:

The unit will still try and receive the signal every day despite it being manually set. When it does receive the

signal, it will change the manually set time into the received time. During reception attempts the WWVB tower

icon will flash. If reception has been unsuccessful, then the WWVB tower icon will not appear but reception

will still be attempted the following hour.

WWVB time reception takes place from 12:00 am through 6:00 am each day (attempts WWVB reception every

full hour within this time frame). When the time signal is received for example at 1:00 am, the atomic clock

will not attempt to receive the WWVB signal for the remaining hours until 6:00 am. Therefore, the next signal

attempt will take place between 12:00 am and 6:00 am the next day. The other times WWVB reception takes

place, are upon setup and after manual time set exiting mode. Reception is generally not possible during

daylight hours due to the interference of the sun.

YEAR SETTING

The year can be selected sequentially from 2000 to 2049 and will then start over again (default setting 2000).

Only the last 2 digits of the year will be visible on LCD2.

1. The year digits will start flashing on LCD2. Select the desired year by use of the +key.

2. Press and release the SET key to switch to the “Month Setting”.

MONTH SETTING

1. The month digits on LCD2 will start flashing. Set the desired month by use of the +key.

2. Press and release the SET key to move to the mode “Date Setting”.

DATE SETTING

1. The digits for the date will start flashing on LCD2 (Default setting 1). Set the desired date by use of the +

key.

Note: The date can only be set in conjunction with the selected month. For example, it is not possible to set

the date 30 if the month of February is selected.

2. Press and release the SET key to enter the “Weekday Setting”.

WEEKDAY SETTING

1. The weekday symbols will be displayed on LCD2 in the pre-set language and flashing. Set the desired

weekday by use of the + key.

2. Press and release the SET key to enter the mode “12/24 Hours Time Display Setting”.

12/24 HOURS TIME DISPLAY SETTING

1. The “12” or “24” will start flashing in LCD1 (Default setting 12h). Select the desired time display mode by

use of the + key.

2. Press and release the SET key to enter the “ºC/ºF Temperature Setting“.

°C OR °F TEMPERATURE SETTING

1. The characters “°C” or “°F” will start flashing on LCD1 (Default setting °F). By use of the +key select

“°C” for temperature display in degrees Celsius or “°F” for degrees Fahrenheit.

2. Press and release the SET key to exit the setting mode and switch back to the normal display mode.

EXIT THE MANUAL SETTING MODES

To return to the normal display mode from anywhere in manual setting mode simply press the SNZ key

anytime.

If no keys are pressed for at least 15 seconds in setting mode, the atomic clock will automatically switch

back to normal display mode.

ALARM SETTING

To enter into the alarm setting mode:

1. Hold the ALM key for 4 seconds. The hour digits start flashing.

2. Press and release the + key to set the hour.

3. Press and release the ALM key to set the minutes. The minute digits start flashing.

4. Press and release the + key to set the minutes.

5. Press and release again the ALM key to exit the Alarm setting mode or wait for 15 seconds automatic

timeout.

TO DEACTIVATE THE ALARM:

The alarm will be automatically ON when the alarm time is set. To deactivate the alarm (OFF), press and

release once the ALM key in normal mode display. The alarm icon will disappear, the alarm is now off.

SNOOZE SETTING

The snooze can only be activated during alarm time for a snooze duration of 10 minutes by pressing the SNZ

key on the back of the clock

Alarm icon

((())) (ON)

OUTDOOR TEMPERATURE TRANSMITTER:

The temperature is measured and transmitted to the atomic clock every 1 minute. The atomic clock will update

the temperature display every 5 minutes.

The range of the outdoor temperature transmitter may be affected by the temperature. At cold temperatures the

transmitting distance may be decreased. Please bear this in mind when positioning the transmitter. Also the

batteries may be reduced in power during periods of extreme cold temperatures.

433MHz RECEPTION CHECK FOR OUTDOOR TEMPERATURE TRANSMITTER

The atomic clock will receive the temperature data within 10 minutes. If the temperature data is not received 10

minutes after setting up (the display shows “- - -”), then please check the following points:

1. The distance of the atomic clock or outdoor temperature transmitter should be at least 6 feet away from any

interfering sources such as computer monitors or TV sets.

2. Avoid placing the receiver onto or in the immediate proximity of metal window frames.

3. Using other electrical products such as headphones or speakers operating on the same signal frequency

(433MHz) may prevent correct signal transmission and reception.

4. Neighbors using electrical devices operating on the 433MHz signal frequency can also cause interference.

Note:

When the 433 MHz signal is received correctly, do not re-open the battery cover of either the outdoor

temperature transmitter or atomic clock, as the batteries may spring free from the contacts and force a false

reset. Should this happen accidentally then reset all units (see Setting up above) otherwise transmission

problems may occur.

The maximum transmission range is 200 feet from the outdoor temperature transmitter to the atomic clock (in

open space). However, this depends on the surrounding environment and interference levels. If no reception is

possible despite the observation of these factors, all system units have to be reset (see Setting up). See our

website www.skyscaninfo.com for more information.

CHANGING THE DISPLAY MODE (DAY, SECONDS, AND TEMPERATURES)

There are four possible display modes to view the day, seconds, and temperatures.

The month&date/weekday/indoor temperature/outdoor temperature is the default.

To change the display:

1. Press the + key. The display should now show the month&date/weekday/seconds/outdoor temperature.

2. Press the + key a second time and the display will now show the month&date/weekday/indoor

temperature/seconds.

3. Press the + key third time and the display will now show the month&date/seconds/indoor

temperature/outdoor temperature

4. Press the + key a fourth time and the display will return to the default display.

WWVB RADIO CONTROLLED TIME

The NIST radio station, WWVB, is located in Ft. Collins, Colorado and transmits the exact time signal

continuously throughout the United States at 60 kHz. The signal can be received up to 2,000 miles away through

the internal antenna in the atomic clock. However, due to the nature of the Earth’s Ionosphere, reception is very

limited during daylight hours. The atomic clock will search for a signal every night when reception is best. The

WWVB radio station derives its signal from the NIST atomic clock in Boulder, Colorado. A team of atomic

physicists continually measures every second of every day to an accuracy of ten billionths of a second a day.

These physicists have created an international standard, measuring a second as 9,192,631,770 vibrations of a

Cesium 133 atom in a vacuum. This atomic clock regulates the WWVB transmitter.

Once the outdoor temperature is displayed on the atomic clock, the WWVB tower icon in the clock display will

start flashing in the top center of the LCD. This indicates that the clock has detected a radio signal and is trying

to receive it. When the time code is received, the WWVB tower becomes permanently lit and the time will be

displayed.

If the tower icon flashes, but does not set the time or the WWVB tower does not appear at all, then please take

note of the following:

Recommended distance to any interfering sources like computer monitors or TV sets is a minimum of 6 feet.

Within ferro-concrete rooms (basements, superstructures), the received signal is naturally weakened. In

extreme cases, please place the unit close to a window and/ or point its front or back towards the Fort

Collins, Colorado, transmitter.

During nighttime, the atmospheric disturbances are usually less severe and reception is possible in most

cases. A single daily reception is adequate to keep the accuracy deviation below 1 second.

Note:

In case the atomic clock is not able to detect the WWVB-signal (disturbances, transmitting distance, etc.), the

time can be manually set (please refer to notes on Manual time setting) .

ICON DESCRIPTION:

POSITIONING

Before permanently mounting ensure that the atomic clock is able to receive WWVB signals from the desired

location. Also, extreme and sudden changes in temperature will decrease the accuracy of the atomic clock, and

changes in elevation will result with inaccurate temperatures readings for the next 12 to 24 hours. These changes

will require a 12 to 24 hour wait before obtaining reliable data.

Successful reception of

WWVB time signal

Currently searching for the

WWVB time signal (tower

blinking)

Unsuccessful reception of WWVB

signal. Will work as normal quartz

clock. Will search for the WWVB time

signal overnight.

POSITIONING THE ATOMIC CLOCK:

There are two possible ways to mount the atomic clock:

use of the foldout table stand, or

wall mounting

FOLDOUT TABLE STAND

The foldout table stand leg is located on the backside. Pull the stand out from the bottom center edge of

the atomic clock, below the battery compartment. Once the foldout table stand is extended, place the

atomic clock in an appropriate location.

WALL MOUNTING

1) Using a straightedge, horizontally space at 2.36 inches (60 mm) three screw positions on a wall.

2) Install three mounting screws (not included) into a wall within transmission range—leaving

approximately 3/16 of an inch (5mm) extended from the wall.

3) Place the atomic clock onto the screws, using the hanging holes on the backside. Gently pull the

atomic clock down to lock the screws into place.

Note:

Always ensure that the atomic clock locks onto the screws before releasing.

POSITIONING THE OUTDOOR TEMPERATURE TRANSMITTER

To achieve a true temperature reading, avoid mounting where direct sunlight can reach the outdoor temperature

transmitter. It is recommended to mount the outdoor temperature transmitter on a North-facing wall or in any

well shaded area. The maximum transmitting range is 200 feet obstacles such as walls, concrete, and large metal

objects can reduce the range.

Place both units in their desired location, and wait approximately 10 minutes before permanently mounting to

ensure that there is proper reception. The outdoor temperature transmitter is not waterproof and should not be

placed anywhere it will become submerged in water or be directly in the rain.

The outdoor temperature transmitter can be mounted in two ways:

with the use of screws, or

using the adhesive tape.

MOUNTING WITH SCREWS

1) Remove the mounting bracket from the outdoor temperature transmitter.

2) Place the mounting bracket over the desired location. Through the three screw holes of the

bracket, mark the mounting surface with a pencil.

3) Where marked, start the screw holes into mounting surface.

4) Screw mounting bracket onto the mounting surface. Ensure that the screws are flush with

the bracket.

This manual suits for next models

Table of contents

Popular Clock manuals by other brands

Silicon Laboratories

Silicon Laboratories SI5324 manual

Heathkit

Heathkit GC-1005 Assembly manual

Oregon Scientific

Oregon Scientific PRYSMA RMR221P manual

Andrew O'Malley

Andrew O'Malley DOTKLOK Assembly instructions

ALGE-Timing

ALGE-Timing ASC3 manual

Bodet

Bodet Profil 960 Installation and operating instructions

Nixie Clock

Nixie Clock Divergence Meter user manual

La Crosse Technology

La Crosse Technology WS-8256-AL user manual

Mini Gadgets

Mini Gadgets MCPro user manual

Casio

Casio TMR-200 user guide

Progetti

Progetti ILTEMPOSTRINGE Directions

BVItech

BVItech BV-101 instruction manual

Progetti

Progetti KALIMERO Directions

La Crosse Technology

La Crosse Technology WT-3141b Quick setup instructions

La Crosse Technology

La Crosse Technology W86531 owner's manual

Sharp

Sharp SPC900 instruction manual

La Crosse Technology

La Crosse Technology 404-50447 quick start guide

Datexx

Datexx DF0063 quick guide