Siemens SITRANS LR260 User guide

1 of 2

1954 Technology Drive, P.O. Box 4225

Peterborough, Ontario

K9J 7B1 / Canada

Tel.: (705) 745-2431

Fax: (705) 741-0466

www.siemens.com/sensorsystems

Siemens Canada Limited

Siemens Milltronics Process Instruments

G050212

SITRANS LR260/LR250 hybrid use on liquid applications

Equipment: SITRANS LR260 features higher gain microwave electronics, typically 15 dB higher than the

LR250. Configurations of SITRANS LR260 electronics and LR250 with 2” threaded process

connections are available as standard catalog items and others are available by special

request. Contact your Siemens representative.

While every effort was made to verify the following information, no warranty of accuracy or usability is expressed or

implied.

Applications

Appropriate applications for the LR260/250 hybrid are:

1. Longer range applications from 20 m (66 ft) to 30 m (98 ft).

2. Applications with low dielectric AND small process connections.

3. Challenging applications where turbulence or minor foam is present.

Configurations

2 inch threaded connection versions are released and available as standard options on the SITRANS LR260 catalog sheet. Any

other SITRANS LR250 process connection option is available by special request. Contact your Siemens representative.

SITRANS LR260 with 2”NPT process connection and antenna is shown below.

APPLICATION GUIDE

SITRANS LR260/LR250 hybrid use on liquid applications

AG050212 2 of 2

APPLICATION GUIDE

Signal Comparisons (Reference Conditions)

SITRANS LR250 - 2” horn SITRANS LR260 - 2” horn

A signal to noise ratio improvement of 18 dB is shown above. This gain improvement will be obtained on any target distance.

Specifications

All specifications and approvals will be per the SITRANS LR260 except process related specifications such as pressure and

process temperature as these will be derived from the LR250 process connection specification.

LR260 Programming for optimization on liquids

1. Use the Quick start wizard to setup the application then make the following additional changes:

a. Par 2.2.4.1 Algorithm: set to tF.

b. Par 2.2.4.1.2 Echo Position: set to COM.

i. COM (Center of Mass) detection method is recommended for flat surfaces (liquids) and

RE (Rising Edge) detection method is recommended for sloped surfaces (solids)

c. Par 2.2.4.3.7 Reform: set to 0. It is recommended that this filter only be used in solids applications.

Other manuals for SITRANS LR260

This manual suits for next models

Table of contents

Other Siemens Transmitter manuals

Siemens

Siemens sitrans PROBE LU User manual

Siemens

Siemens SITRANS P210 Administrator guide

Siemens

Siemens REV23.03RF User manual

Siemens

Siemens SITRANS TH Series Administrator guide

Siemens

Siemens SITRANS P 7MF1580 Series User manual

Siemens

Siemens SITRANS L Series User manual

Siemens

Siemens SITRANS L Series Administrator guide

Siemens

Siemens Sitrans Probe LR Instruction manual

Siemens

Siemens RPT User manual

Siemens

Siemens sitrans lr 460 User manual

Siemens

Siemens 7MF8*24 Series Administrator guide

Siemens

Siemens SITRANS LR260 Instruction manual

Siemens

Siemens SITRANS FUS060 PA User manual

Siemens

Siemens SITRANS LR260 User manual

Siemens

Siemens Sitrans LR250 User manual

Siemens

Siemens SITRANS LR260 Instruction manual

Siemens

Siemens SITRANS P220 Administrator guide

Siemens

Siemens SITRANS Series User manual

Siemens

Siemens Sitrans LR250 Administrator guide

Siemens

Siemens SITRANS TH400 User manual

Siemens

Siemens 8DJH Manual

Siemens

Siemens SITRANS TF2 User manual

Siemens

Siemens SITRANS P300 User manual

Siemens

Siemens SITRANS L LU150 User manual

Popular Transmitter manuals by other brands

NIVELCO

NIVELCO EasyTREK SCA-300 Series Programming manual

Honeywell

Honeywell 5816WMBR installation instructions

Kamstrup

Kamstrup READy MTU Installation and operation guide

Omega

Omega ZW Series user guide

ABB

ABB Field 264H Instructions for installation

Alinco

Alinco DJ-V17T Service manual

Dejero

Dejero EnGo 3x manual

Rosemount

Rosemount 4600 Reference manual

Speaka Professional

Speaka Professional 2342740 operating instructions

trubomat

trubomat GAB 1000 instruction manual

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 instructions

Rondish

Rondish UT-11 quick start guide

MG 10JRE instruction manual

Burkert

Burkert 8177 operating instructions

Firetide

Firetide HotPort 3203 Hardware installation guide

Tele Radio

Tele Radio T9-02 User instructions

Rotronic

Rotronic HygroFlex HF3 Series user guide

Jamara

Jamara FCX6 Pro Tel Instruction