Siemens FS-DACT User manual

Siemens Industry, Inc. Siemens Canada Limited

Building Technologies Division Building Technologies Division

Florham Park, NJ 2 Kenview Boulevard

Brampton, Ontario L6T 5E4 Canada

P/N 315-699464-10 (v10-21-10)

INSTALLATION INSTRUCTIONS

Model FS-DACT

Serial Digital Alarm Communicator Transmitter (DACT)

The FS-DACT Digital Alarm Communicator Transmitter Board is an optional module for the FS-250 and

FS-250C Fire Alarm System Control Panels. The FS-DACT provides telephone line connections for

communication with a DACR (Digital Alarm Communicator Receiver). The FS-DACT Board is mounted

on the Main Board. The FS-DACT Board options are set through the control panel programming

sequence.

PARTS SUPPLIED

1 FS-DACT Board

4 Spacers, 1”

1 Keps Nut, #6-32

1 Instruction Sheet

FS-DACT MOUNTING for FS-250 OR FS-250C

Step 1.) Installation is to be done by qualified personnel

who have thoroughly read and understood this

instruction sheet.

Step 2.) Disconnect BATTERY and AC prior to working on

equipment.

Step 3.) Mount DACT Board as shown, using four spacers

to the Main Board.

NOTE: Check to see that the header and

connectors are mated properly.

Step 4.) Attach ground wire as shown, using the nearest

main board mounting screw as shown.

Step 5.) Attach conduit and run wires as required.

Step 6.) Connect wires to the fire alarm system control unit

as required.

Step 7.) Apply power to system.

Step 8.) Program for proper operation of functions.

a) Tech Level>>Outputs>Option Mods>DACT CFG

(Set DACT line and general configurations)

b) Tech Level>>Outputs>Option Mods>DACT ACCTS

(Set DACT account configurations)

c) Maint Level>>Disable/Enable>Outputs>DACT

>Enabled

NOTE: See Programmer’s Manual (P/N 315-

049403[C]) for more details on programming.

Step 9.) Check for proper operation of functions.

P/N 315-699464-10 2

FS-DACT WIRING

NOTE: The RJ31X provides a convenient connection allowing the DACT to be installed and removed without requiring re-wiring and

can be installed by the telephone installer.

NOTE: If installed in Canada, the signal receiving centre must not share a common communication channel with the protected

premises. A dedicated line must be installed for use only by the FS-DACT.

FS-DACT FORMAT DESCRIPTION

Format Description

SIA DCS 8 Security Industry Association - Digital Communications Standard. Format may send up to eight events a call.

SIA 1997 Level Ia compatibility with support for O (old) blocks and 300 Baud (FAST) operation.

Sends an account number (up to 6 digits), a 2 character code and 3-digit identifier up to four times with FSK

frequency encoding.

SIA DCS 20 See SIA DCS 8, except format may send up to twenty events a call.

Ademco Contact ID Sends a 4-digit account number, a 3-digit code and 3-digit identifier up to four rounds of dual tone multiple

frequency with 1400 and 2300 Hz handshake frequency.

3/1 1400HZ Sends a 3-digit account number and a 1-digit code up to four rounds at 20 pps with 1400 Hz handshake

frequency.

3/1 2300HZ Sends a 3-digit account number and a 1-digit code up to four rounds at 20 pps with 2300 Hz handshake

frequency.

4/2 1400HZ Sends a 4-digit account number and a 2-digit code up to four rounds at 20 pps with 1400 Hz handshake

frequency.

4/2 2300HZ Sends a 4-digit account number and a 2-digit code up to four rounds at 20 pps with 2300 Hz handshake

frequency.

COMPATIBLE RECEIVERS/FORMATS

Receiver

Manufacturer Compatible

Receivers SIA DCS

8 SIA DCS

20 Ademco

Contact ID 3/1

1400HZ 3/1

2300HZ 4/2

1400HZ 4/2

2300HZ

Osborne-Hoffman,

Inc. QUICKALERT!

Model II Ademco

Contact ID Fast 3+1

1400HZ Fast 3+1

2300HZ Fast 4+2

1400HZ Fast 4+2

2300HZ

Osborne-Hoffman,

Inc. OH2000 SIA 1 SIA 1 Ademco

Contact ID Fast 3+1

1400HZ Fast 3+1

2300HZ Fast 4+2

1400HZ Fast 4+2

2300HZ

Radionics, Inc. D6500 3x1 3x1 4x2 4x2

Silent Knight Security

Corp. 9000 SIA 8 SIA 20 SK 3/1 SK 3/1 SK 4+2 SK 4+2

Silent Knight Security

Corp. 9500 SIA DCS SIA DCS Ademco

Contact ID SK 3/1 SK 3/1 SK 4+2 SK 4+2

Silent Knight Security

Corp. 9800 SIA DCS SIA DCS Ademco

Contact ID SK 3/1 SK 3/1 SK 4+2 SK 4+2

Telephone Line Connection Ratings:

Power Limited

Supervised

Voltage: 24VDC nominal, 0.054A max.

Ringer Equivalence: 0.4B

Telephone Line #1

Connection from TELCO

Optional Output to telephone

(Note: The DACT may seize

the line to report events)

Telephone Line #2

Connection from TELCO

Optional Output to telephone

(Note: The DACT may seize

the line to report events)

8-PIN

MODULAR

PLUG

8-PIN

MODULAR

PLUG

RED

GREEN

GREY

BROWN

RED

GREEN

GREY

BROWN

RJ31X

JACK

RJ31X

JACK

TIP

RING

TIP

RING

TIP

RING

TIP

RING

P/N 315-699464-10 3

FS-DACT EVENT CODES

Event Type SIA DCS

(8 or 20)*Ademco

Contact ID**

3/1

1400 Hz or

2300HZ

4/2

1400 Hz or

2300HZ

Fire Point Alarm FA tuvw 1 110 xyz 0 01

Fire Point Alarm Restore

(Through Reset)

FH tuvw 3 110 xyz 2 21

Waterflow Point Alarm SA tuvw 1 113 xyz 0 02

Waterflow Point Restore SH tuvw 3 113 xyz 2 22

General Alarm FA 298 1 110 298 0 01

Supervisory Point Active SS tuvw 1 203 xyz 6 66

Supervisory Point Restore SR tuvw 3 203 xyz 7 76

AC Trouble AT 0 1 301 000 8 80

AC Trouble Restore AR 0 3 301 000 7 70

Power Up/Reset RR 0 3 305 000 7 70

Fire Point Trouble FT tuvw 1 373 xyz 8 83

Fire Point Trouble Restore FJ tuvw 3 373 xyz 7 73

Fire Trouble Restore (All Clear) FJ 9 3 373 009 7 79

Fire Point Device Bypass (Disable) FB tuvw 1 571 xyz 8 84

Group, Zone or Panel Relay Bypass

(Disable) FB 298 1 571 298 8 84

Releasing Circuits Bypassed (Disable) SS 298 1 203 298 6 66

Releasing Circuits Unbypassed (Enable) SR 298 3 203 298 7 76

Fire Point Device Unbypass (ReEnable) FU tuvw 3 571 xyz 7 74

Group, Zone or Panel Relay Unbypass

(ReEnable) FU 298 3 571 298 7 74

NAC Bypass (Disable) FB 2nn 1 571 4nn 8 84

NAC Unbypass (ReEnable) FU 2nn 3 571 4nn 7 74

System Battery Trouble YT 298 1 302 298 8 87

System Battery Trouble Restore YR 298 3 302 298 7 77

NAC Circuit nn Trouble FT 2nn 1 373 4nn 8 83

NAC Circuit nn Trouble Restore FJ 2nn 3 373 4nn 7 73

NAC Circuit Ground Fault FT 299 1 373 299 8 89

NAC Circuit Ground Fault Restore FJ 299 3 373 299 7 73

FDLC Ground Fault Trouble FT 299 1 373 299 8 83

FDLC Ground Fault Trouble Restore FJ 299 3 373 299 7 73

FDLC Trouble FT 30d 1 373 298 8 83

Phone Line 1 Trouble LT 1 1 351 001 8 81

Phone Line 1 Trouble Restore LR 1 3 351 001 7 71

Phone Line 2 Trouble LT 2 1 352 002 8 82

Phone Line 2 Trouble Restore LR 2 3 352 002 7 72

Dialer Data Lost RT 30 1 354 030 8 88

Fire Test (Drill) begin FI 0 1 604 000 9 90

Fire Test (Drill) end FK 0 3 604 000 9 92

Quick Test Begin FT 298 1 373 298 8 83

Quick Test Stop FJ 298 3 373 298 7 73

System Trouble qrs FT qrs 1 373 qrs 8 83

System Trouble qrs Restore FJ qrs 3 373 qrs 7 73

Auto Test – System Normal RP 30 1 602 030 9 93

Manual Test – System Normal*** TX 30 1 601 030 9 99

Point Active in Quick Test FX tuvw 1 604 xyz 9 91

***

Note: Below Panel Firmware revision 6.3, this code is always paired with the Auto Test Code (RP 30, etc.) during the daily automatic test.

nn denotes NAC circuit number 1-12.

ddenotes FDLC number.

Important: Account 1 and Account 2 must be set for the same reporting format. See the FS-250 Programming

Manual, P/N 315-049403, or the FS-250C Programming Manual, P/N 315-049403C, as applicable, for details on

setting the reporting format.

P/N 315-699464-10 4

SIA / ADEMCO

SYSTEM TROUBLE CODES

Trouble Type q r s

Network Trouble 2 9 0

DACT General Trouble 2 9 1

DACT Account 1 2 9 2

DACT Account 2 2 9 3

General Trouble 2 9 8

FCC Requirements - Part 68

This equipment complies with Part 68 of the Federal Communication Commission (FCC) Rules and Regulations. On

the bottom is a label that contains, among other information, the FCC Registration Number and Ringer Equivalence

Number (REN) for this equipment. If requested, this information must be provided to the telephone company.

FCC Registration Number: ABK USA-34988-AL-E

USOC telephone jack: RJ31X

Ringer Equivalence Number (REN):0.4B

The REN is useful to determine the quantity of devices which may connect to the telephone line. Excessive REN’s on

the telephone line may result in the devices not ringing in response to an incoming call. In most, but not all areas, the

sum of the REN’s should not exceed five (5.0). To be certain of the number of devices that may be connected to the line,

as determined by the total REN’s, contact the telephone company to determine the maximum REN for the calling area.

If the FS-DACT equipment causes harm to the telephone network, the telephone company will notify you in advance

that temporary discontinuance of service may be required. If advance notice is not practical, the telephone company

will notify you of the discontinuance as soon as possible. Also, you will be advised of your right to file a complaint with

the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the

operation of your telephone equipment. If this happens, the telephone company will provide advance notice so that

you can modify your equipment as required to maintain uninterrupted service.

If you experience trouble with the FS-DACT Board for repair and/or warranty information please contact an authorized

Siemens Fire Safety representative.

If the trouble is causing harm to the telephone network, the telephone company may request you disconnect to

equipment from the network until the problem is solved. You should not attempt to repair this equipment yourself. This

equipment contains no customer or user serviceable parts.

This device may not be used on public coin or party line services.

Changes or modifications not expressly approved by Siemens Fire Safety could void your authority to operate this

equipment.

SIA DCS

*EVENT CODE IDENTIFIER DESCRIPTIONS

4 Digit Code t u v w

Device Address Loop (1-4) Address (001-252)

ADEMCO CONTACT ID

**EVENT CODE IDENTIFIER DESCRIPTIONS

x y z

Input Group # Address (001 – 240)

Other Siemens Transmitter manuals

Siemens

Siemens SITRANS LR260 User manual

Siemens

Siemens SITRANS TH400 User manual

Siemens

Siemens Sitrans LR200 Instruction manual

Siemens

Siemens SITRANS TH400 User manual

Siemens

Siemens SITRANS P310 with HART Administrator guide

Siemens

Siemens SITRANS P DS III User manual

Siemens

Siemens Sitrans LR250 User manual

Siemens

Siemens SITRANS P 7MF1562 User manual

Siemens

Siemens SITRANS P300 User manual

Siemens

Siemens Sitrans LU-180 User manual

Siemens

Siemens SITRANS P500 Administrator guide

Siemens

Siemens Sitrans LR250 Administrator guide

Siemens

Siemens SITRANS LH100 Administrator guide

Siemens

Siemens SITRANS P500 Administrator guide

Siemens

Siemens SITRANS DS III series Administrator guide

Siemens

Siemens 7ml12011ef00 User manual

Siemens

Siemens SITRANS P 7MF1580 Series User manual

Siemens

Siemens SITRANS TF2 User manual

Siemens

Siemens sitrans lc 300 User manual

Siemens

Siemens US-100-1 User manual

Siemens

Siemens SITRANS LH100 Administrator guide

Siemens

Siemens 7ML5431 User manual

Siemens

Siemens SITRANS LR260 Instruction manual

Siemens

Siemens SITRANS T Series User manual

Popular Transmitter manuals by other brands

NIVELCO

NIVELCO EasyTREK SCA-300 Series Programming manual

Honeywell

Honeywell 5816WMBR installation instructions

Kamstrup

Kamstrup READy MTU Installation and operation guide

Omega

Omega ZW Series user guide

ABB

ABB Field 264H Instructions for installation

Alinco

Alinco DJ-V17T Service manual

Dejero

Dejero EnGo 3x manual

Rosemount

Rosemount 4600 Reference manual

Speaka Professional

Speaka Professional 2342740 operating instructions

trubomat

trubomat GAB 1000 instruction manual

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 instructions

Rondish

Rondish UT-11 quick start guide

MG 10JRE instruction manual

Burkert

Burkert 8177 operating instructions

Firetide

Firetide HotPort 3203 Hardware installation guide

Tele Radio

Tele Radio T9-02 User instructions

Rotronic

Rotronic HygroFlex HF3 Series user guide

Jamara

Jamara FCX6 Pro Tel Instruction