Siemens ZIC-8B User manual

SiemensSiemens

Siemens IndustryIndustry

IndustryIndustry

Industry,,

,Inc.Inc.

Inc.Inc.

Inc.

BuildingBuilding

Building

Tecec

ecec

echnologies Dihnologies Di

hnologies Dihnologies Di

hnologies Divisionvision

visionvision

vision

P/N 315-048670-11

INTRODUCTION The Model ZIC-8B from Siemens Industry, Inc., is a zone

indicating card that provides notification appliance circuits for

the FireFinder-XLS/Desigo Fire Safety Modular/Cerberus PRO

Modular system. It has 8 outputs that can be configured as

Class B only for control of audible and visual notification

appliances such as horns, speakers, bells, strobes, etc.

Each zone can be configured independently for different

usages as programmed in the Zeus tool and can be controlled

automatically by program logic or manually using the PMI/

PMI-2/PMI-3 (XLS), FCM2041-U2 (Desigo Fire Safety Modu-

lar), FCM2041-U3 (Cerberus PRO Modular). Installation of a

ZIC-2C Zone Indicating Card on the ZIC-8B gives it two

channel audio capability.

The ZIC-8B supports synchronized and non-synchronized

strobes.This selection is available in the Zeus tool under the

detail properties for each ZIC-8B circuit. Synchronization across

multiple ZIC-8B cards is automatic as a part of the FireFinder-

XLS/Desigo Fire Safety Modular/Cerberus PRO Modular

operating characteristics. Refer to document P/N 315-096363

for a list of strobes that support synchronization.

Features ZIC-8B features are as follows:

• Class B circuit configuration

• Zones can be configured independently

(See Note on Restrictions, page 2)

• Can have independent input source for

every 2 outputs

• Zone input voltage supervision per input (DC only)

• Zone output supervision

• Intelligent self-restoring power limiting

• Coded signal synchronization capability

• Card level Ground Fault detection

• Communicate H-Net protocol

• Uploadable firmware update

• Ability to pass through up to 2A per output circuit

GND FAULT

TRBL

ZONE 4 ACTIVE

TRBL

ZONE 2 ACTIVE

ZONE 1 ACTIVE

TRBL

ZONE 3 ACTIVE

CARD FAIL

HNET FAIL

CAN FAIL

RESET

POWER

ZIC-8B

HNET/CAN

HUNDREDS

TENS

ONES

TRBL

ZONE 8 ACTIVE

TRBL

ZONE 6 ACTIVE

ZONE 5 ACTIVE

TRBL

ZONE 7 ACTIVE

Figure 1

ZIC-8B Zone Indicating Card

Zone Indicating Card

Installation Instructions

Model ZIC-8B

Siemens Industry, Inc.

Building Technologies Division

P/N 315-048670-112

RESTRICTIONS

Each zone input supplies power to two adjacent zone outputs as follows:

Zone Input Zone Output

1 1 and 2

2 3 and 4

3 5 and 6

4 7 and 8

Adjacent associated output zones must have the same usage. Each output must not

draw greater than 2A@24 VDC. During system test be sure to activate each zone

output pair to ensure that the maximum zone input current is not exceeded.

When any of the ZIC-8B output circuits are used for speakers the following rules apply:

1. The output circuits are available in two groups, 1-4 and 5-8.

2. Either output group can be used for speakers or NACs.

3. Each output circuit in an output group must have the same usage.

4. Unused output circuits must not be configured in Zeus.

5. Zone inputs 1-2 feed output circuits 1-4.

6. Zone inputs 3-4 feed output circuits 5-8.

OPERATION The ZIC-8B contains eight Class B circuits. Each circuit is rated at 2A at 24VDC and

has an input connected to the power source and an output where the NAC devices

are connected.The zone inputs are isolated from one another and are supervised for

the presence of power. This allows the use of different power sources with different

ground references. The zone output is supervised for open and short circuit condi-

tions while the zone is inactive and allows different combinations of output configura-

tions (standard NAC, speakers, etc.) per card. Each ZIC-8B card occupies any one

card slot in the CC-5/CC-2 cardcage.The ZIC-8B also has the capability to detect

ground fault on its zone output as indicated by a diagnostic LED. (See Note above.)

Controls and Indicators The front panel of the ZIC-8B contains one reset switch, twenty-one LEDs, and three

HNET address switches as shown in Figure 1.

A reset switch is located on the top of the front panel. Pushing the reset switch

re-initializes the ZIC-8B operation.

The LEDs follow the reset switch and their functions are defined as follows:

POWER (Green) Normally ON. When illuminated, indi-

cates that power for the ZIC-8B is

applied to the card.

CARD FAIL (Yellow) Normally OFF. When illuminated, indicates

that the card microprocessor has failed.

CAN FAIL (Yellow) Normally OFF. When illuminated, indicates

that the CAN communication with the

ZIC-8B has terminated and the card goes

into degrade mode (applicable only when

card resides in a CAN network). NOT USED

for FireFinder-XLS/Desigo Fire Safety

Modular/Cerberus PRO Modular

applications.

HNET FAIL (Yellow) Normally OFF. When illuminated, indi-

cates that the HNET communication with

the ZIC-8B has terminated and the card

goes into degrade mode (applicable only

when card resides in the HNET network).

Siemens Industry, Inc.

Building Technologies Division

P/N 315-048670-113

GND FAULT (Yellow) Normally OFF. When illuminated, indi-

cates that the ZIC-8B has detected either

a negative or positive ground fault on its

field wiring.

ZONE 1 ACTIVE (Red) Normally OFF. When illuminated, indi-

cates that Zone 1 is active.

TROUBLE (Yellow) Normally OFF. When illuminated, indi-

cates that the ZIC-8B has detected a

trouble on Zone 1 (open circuit or short

circuit) or Zone 1 is disarmed.

ZONE 2 ACTIVE (Red) Normally OFF. When illuminated, indi-

cates that Zone 2 is active.

TROUBLE (Yellow) Normally OFF. When illuminated, indi-

cates that the ZIC-8B has detected a

trouble on Zone 2 (open circuit or short

circuit) or Zone 2 is disarmed.

ZONE 3 ACTIVE (Red) Normally OFF. When illuminated, indi-

cates that Zone 3 is active.

TROUBLE (Yellow) Normally OFF. When illuminated, indi-

cates that the ZIC-8B has detected a

trouble on Zone 3 (open circuit or short

circuit) or Zone 3 is disarmed.

ZONE 4 ACTIVE (Red) Normally OFF. When illuminated, indi-

cates that Zone 4 is active.

TROUBLE (Yellow) Normally OFF. When illuminated, indi-

cates that the ZIC-8B has detected a

trouble on Zone 4 (open circuit or short

circuit) or Zone 4 is disarmed.

ZONE 5 ACTIVE (Red) Normally OFF. When illuminated, indi-

cates that Zone 5 is active.

TROUBLE (Yellow) Normally OFF. When illuminated, indi-

cates that the ZIC-8B has detected a

trouble on Zone 5 (open circuit or short

circuit) or Zone 5 is disarmed.

ZONE 6 ACTIVE (Red) Normally OFF. When illuminated, indi-

cates that Zone 6 is active.

TROUBLE (Yellow) Normally OFF. When illuminated, indi-

cates that the ZIC-8B has detected a

trouble on Zone 6 (open circuit or short

circuit) or Zone 6 is disarmed.

ZONE 7 ACTIVE (Red) Normally OFF. When illuminated, indi-

cates that Zone 7 is active.

TROUBLE (Yellow) Normally OFF. When illuminated, indi-

cates that the ZIC-8B has detected a

trouble on Zone 7 (open circuit or short

circuit) or Zone 7 is disarmed.

Siemens Industry, Inc.

Building Technologies Division

P/N 315-048670-114

ZONE 8 ACTIVE (Red) Normally OFF. When illuminated, indi-

cates that Zone 8 is active.

TROUBLE (Yellow) Normally OFF. When illuminated, indi-

cates that the ZIC-8B has detected a

trouble on Zone 8 (open circuit or short

circuit) or Zone 8 is disarmed.

Three rotary dial switches at the bottom of the front panel are used to set the HNET

network address of the ZIC-8B.

Output Zones The ZIC-8B output zones can be configured as 25V or 70V speaker zones or for the

following standard NAC Zone usages:

Steady

Strobe (Synchronized or Unsynchronized)

Zone Coding

Temporal Code

Temporal 4, when used with Audible Base SBGA-34

March Time 120

March Time 60

March Time 30

Canadian 2 stage - 30

Canadian 2 stage - 120

Sync Horn Strobe

Programming Options In order to perform its intended operation, the ZIC-8B card must be programmed

using the Zeus Programming Tool.The ZIC-8B card and its Out Ckt properties must

be set prior to normal operation.

In the Zeus Programming Tool, highlight the selected ZIC-8B card in the Physical

View and open the Detail View - Properties to modify and/or define the following

ZIC-8B card properties:

HNET Address This address must match the address

set in ZIC-8B hardware.

Base Language Custom Message The message associated with ZIC-8B card.

Alternate Language Custom Message The message associated with ZIC-8B

card in an alternate language.

ZIC CARD 24V Power Source Select back plane or screw termnals.

ZIC-2C Card Installed Check if ZIC-2C card is installed.

Each ZIC-8B card is subdivided into eight output circuits that can be programmed

independently. In the Zeus Programming Tool, highlight the selected ZIC-8B Output

Ckt in the Physical View and open the Detail View - Properties to modify and/or

define the following ZIC-8B output circuit properties:

Device Address Shows preset address of ZIC card output.

Base Language Custom Message The message associated with the ZIC-8B

output circuit.

Siemens Industry, Inc.

Building Technologies Division

P/N 315-048670-115

Alternate Language Custom Message The message associated with the ZIC-8B

output circuit in an alternate language.

Device Usage The device usage of the ZIC-8B signal.

ZIC Circuit Usage Select usage required from: NAC-Steady,

NAC-Coded, Horn Strobe Sync, Sil Horn

Only (Horn Strobe), Strobe Sync, Strobe

UnSync, 25V Speaker, 70V Speaker, and

100V Speaker.

Degrade Mode Alarm Activation Determines if Degrade Alarm will activate

the ZIC-8B circuit when asserted.

Silenceable Option Determines if the circuit is Silenceable or

Non-Silenceable.

Wiring Type The circuit wiring type must be Class B.

Total Current Drawn Select actual current load of output

circuit from: 0.0 Amp, 0.5 Amp, 1.0 Amp,

1.5 Amp and 2.0 Amp.

Some restrictions apply to certain usage selections that are enforced by the Zeus

tool during Edit mode or Compile time.

Refer to the Zeus Quick Start Manual, P/N 315-033875, or the Zeus self-help index

for more information.

PRE-INSTALLATION The following components must be set prior to inserting the card into the CC-5/CC-2

(refer to Figure 2):

S2, Reset Switch: Momentarily Closed

switch that when pressed will initiate a hard

reset to the ZIC-8B (similar to a cold boot).

S3, S4, S5 Network Address Switch: Set

the three-digit HNET network address for

the ZIC-8B using the three rotary dial

address switches located near the bottom

of the front panel. (Refer to Figure 1 for the

location of the switches.) The address for

the ZIC-8B must be the same as the

address selected for it in the Zeus Program-

ming Tool. To set the address, turn the

pointers on each of the three dials to the

numbers for the selected address. For

example, if the address is 123, set the

pointer for the HUNDREDS dial to “1”, set

the pointer for the TENS dial to “2”, and set

the pointer for the ONES dial to “3”. The

range of allowable addresses is from 001 to

251 (leading zeros must be used).

Figure 2

ZIC-8B Switch Location

96 PIN DIN

PLUG

CONNECTOR

RESET

SWITCH

NAC INPUT

SUPERVISION

ENABLE

ZIC-2C

ZIC-8B

CONNECTORS

TO ZIC-8B

PC BOARD

NETWORK

ADDRESS

INPUT

POWER

SELECT

EXT

POWER

HNET

Siemens Industry, Inc.

Building Technologies Division

P/N 315-048670-116

S1 Input Power Select: This switch consists of three individual switches which must

all be set in the same position. Use S1 to select the source of voltage input to power

the ZIC-8B. BP Power (Backplane Power) indicates that the input is derived from the

backplane of the CC-2/CC-5 and EXT Power (External Power) indicates that the input

is derived from E5/E11 terminal of the CC-2/CC-5, normally connected to non-power

limited output of the PSC-12/PSX-12. It is important to take into account the source

of the voltage during battery calculations.

P3, P4, P5, P6 Shunt Headers, NAC Input Supervision Enable: These headers

select the NAC input zone supervision. If usage application is set for speaker func-

tion, place the shunt jumpers of the corresponding zone between 1—2 and be-

tween 5—6, otherwise place the shunt jumpers between 2—4 and 3—5.

P3 selects NAC input supervision for Zone 1

P4 selects NAC input supervision for Zone 2

P5 selects NAC input supervision for Zone 3

P6 selects NAC input supervision for Zone 4

ZIC-2C If the ZIC-2C will be used for two channel capability, install it now on the

ZIC-8B PC board. Connect the ZIC-2C PC Board to the ZIC-8B by lining up the

connector on the ZIC-2C to the receptacle on the ZIC-8B. Gently insert the connector

into the receptacle being careful not to bend the connector. Refer to Figure 2 for

positioning the ZIC-2C on the ZIC-8B.

WIRING

Remove all system power before installation, first battery then AC. (To power up,

connect the AC first, then the battery.)

All field wiring to the ZIC-8B is connected

to the terminal blocks of the CC-5/CC-2

card cage slot in which it is installed (refer

to Figure 3).

To Connect External Wiring

1. Loosen the screw of the terminal

by turning it counterclockwise.

2. Insert the wire into the side of the

terminal block

3. Tighten the screw of the terminal

block by turning it clockwise.

The top terminals (1 through 8 and 9

through 16) are connected to the notifica-

tion appliance devices such as bells, horns,

strobes, speakers, etc. Each zone has two

terminal connections: (+) and (-). These

terminals are power limited.

The bottom terminals (17 through 24) are

connected to the input power source of the

NAC devices. Each zone has a (+) terminal

and (-) terminal. These terminals are not

power limited.

Figure 3

Wiring The 24VDC Power Lines To

The ZIC-8B Slot In The CC-5/CC-2

12345678

910111213141516

OUTPUTS SHOWN IN ACTIVE STATE

17 18 19 20 21 22 23 24

ZONE 1

ZONE 5

ZONE 1&2

INPUT

ZONE 2

ZONE 6

ZONE 3

ZONE 7

ZONE 4

ZONE 8

ZONE 3&4

INPUT

ZONE 5&6

INPUT

ZONE 7&8

INPUT

ONE SLOT OF CC-5

(SET FOR

NAC INPUT)

Siemens Industry, Inc.

Building Technologies Division

P/N 315-048670-117

Care must be taken when installing the zone input and zone output field wiring to

prevent possible cross wiring.This can cause severe damage to the system when

powered up or when zone is activated.

The screw terminals can accommodate one 12-18 AWG or two 16-18 AWG.

If the total output of all 8 zones exceeds 12 amps, a single PSC-12 cannot be used to

supply the ZIC-8B. Refer to the PSC-12 Installation Instructions, P/N 315-033060 for

information when the total system load exceeds 12 amps.

INSTALLATION The ZIC-8B plugs perpendicularly into one slot in the CC-5/CC-2 card-cage via two 96-

pin DIN connectors and can occupy any slot in the card cage. (Refer to Figure 4.)

Insert the ZIC-8B card into the card guides right side up (lettering on the front panel

is legible)

Slide the card in until the card edge connectors contact

the receptacles on the motherboard.

Verify that the DIN connectors of the card and the card-

cage aligned properly.The card can only plug in one

direction to the card cage, if it does not align, DO NOT

FORCE the card.

Place thumbs on the front panel adjacent to the captive

screws and gently apply even pressure on the card

until the connectors seat in the receptacles on the

motherboard.

Secure with the captive screws.

Power up the system and verify that the ZIC-8B power

LED turns ON.

ELECTRICAL RATINGS

Figure 4

Installing The ZIC-8B

24V Back Plane or

External Power Current See NOTE below

Screw Terminal 24V Current Total Device Current

6.2V Back Plane Current 0

24V Standby Current 105mA

NOTE: The 24V current is dependent on the usage and wiring

type of each ZICCkt of the ZIC-8B. Listed below are the required

current draws for each zone usage and wiring type.

ZIC-8B Current Requirement

Per Output Zone

Zone Usage Output Current

Requirement

Not Used 0

NAC 17mA

Strobe - Sync. 17mA

Strobe - Unsync. 17mA

Speaker Zone - 2 Ch. 34mA

Speaker Zone - 1 Ch. 17mA

NAC - Coded 17mA

ZIC-8B Supervisory State Standby Current =91mA

Siemens Industry, Inc.

Building Technologies Division

P/N 315-048670-118

To calculate the maximum current, the following equation should be used:

ZIC-8B Total Current = ZIC-8B Standby Current + [Zone 1 Usage Req. (See Table above)

+ [Zone 2 Usage Req. (See Table above)

+ [Zone 3 Usage Req. (See Table above)

+ [Zone 4 Usage Req. (See Table above)

+ [Zone 5 Usage Req. (See Table above)

+ [Zone 6 Usage Req. (See Table above)

+ [Zone 7 Usage Req. (See Table above)

+ [Zone 8 Usage Req. (See Table above)

Example 1: If a ZIC-8BA has the following ZICCkt setting:

ZICCkt#1 — Speaker Zone - 2 Ch.

ZICCkt#2 — Speaker Zone - 2 Ch.

ZICCkt#3 — Speaker Zone - 2 Ch.

ZICCkt#4 — Speaker Zone - 2 Ch.

ZICCkt#5 — Speaker Zone - 2 Ch.

ZICCkt#6 — Speaker Zone - 2 Ch.

ZICCkt#7 — Speaker Zone - 2 Ch.

ZICCkt#8 — Speaker Zone - 2 Ch.

By applying the equation above, the maximum current requirement for this card will be

determined.

Max Current = 105 + 34 + 34 +34 + 34 +34 + 34 +34 + 34 = 377mA (worst case).

Example 2: If a ZIC-8B has the following ZICCkt setting:

ZICCkt#1 — NAC

ZICCkt#2 — Strobe Sync

ZICCkt#3 — NAC-Coded

ZICCkt#4 — NAC

ZICCkt#1 — NAC

ZICCkt#2 — Strobe Sync

ZICCkt#3 — NAC-Coded

ZICCkt#4 — Not Used

Max Current = 105 + 17 +17 + 17 + 17 + 17 + 17 + 17 +0 = 224mA.

Siemens Industry, Inc.

Building Technologies Division

P/N 315-048670-119

Figure 5

ZIC-8B Supervised Notification Appliance Wiring

ZONE 1

24K,

ZONE 2

24K,

ZONE 3

24K,

ZONE 4

24K,

----

ZONE 5 ZONE 8

24K,

ZONE 6 ZONE 7

24K,

12345678

910111213141516

17 18 19 20 21 22 23 24

STYLE Y

CLASS B

ZONE 1&2

INPUT

ZONE 3&4

INPUT

ZONE 5&6

INPUT

ZONE 7&8

INPUT

ONE SLOT OF CC-5

NOTES

1. All wiring must be in accordance with

Article 760 of NEC or local building

codes. Wiring for each zone must be

Class B.

2. All output circuits are power limited

to NFPA 70 per NEC 760.

3. Electrical Ratings:

Special Application 24VDC

Output Zone Supervisory:

8mA max @ 24VDC

Output Zone Alarm:

2A max @ 24VDC

4. EOL resistor , 24k ohms,

1W, 5%, P/N 140-033771.

5. Polarity shown in active state.

6. Maximum line resistance is

dependent upon the maximum

current draw of connected notifica-

tion appliances when activated.The

field wiring resistance cannot exceed

the maximum line resistance

specified for any given NAC current

draw. (See Table )

7. For a list of Compatible Notification

Appliances, refer to P/N 315-096363.

8. Refer to CAB1/CAB1R (P/N 315-

0330007) and CAB2-BB/CAB3-BB

(P/N 315-033009) Installation

Instructions for details on the

separation of power limited and non-

power limited wiring.

9. Positive and negative ground fault

detected at <40K for terminals 1 - 16.

10. A maximum of 23 strobes can be

connected to a single circuit.

Current

Draw Max Line

Resistance

2.0A 1.50 ohms

1.5A 2.10 ohms

1.0A 3.30 ohms

0.5A 6.90 ohms

CONFIGURATIONS The ZIC-8B zones can be configured for Notification Applicance (NFPA 72) as shown

below.

Siemens Industry, Inc.

Building Technologies Division

P/N 315-048670-1110

12345678

910111213141516

STYLE Y

(CLASS B)

ONE SLOT OF CC-5

24K,

ZONE 8

ZONE 5

ZONE 1

24K,

STYLE Y

CLASS B

STYLE Y

(CLASS B)

24K,

17 18 19 20 21 22 23 24

TO NEXT ZIC-8B

AUDIO FROM PREVIOUS

ZIC-8B OR ZIC-4A OR FROM

ZAM-180 TERMINALS

1A AND 1B OR 2A AND 2B

ZAC-40/

ZONE 2

24K,

STYLE Y

CLASS B

ZONE 3

24K,

STYLE Y

CLASS B

ZONE 4

24K,

STYLE Y

CLASS B

ZONE 6

STYLE Y

(CLASS B)

24K,

STYLE Y

(CLASS B)

24K,

ZONE 7

NOTES

1. All wiring must be in

accordance with Article 760

of NEC or local building

codes. Wiring for each zone

must be Class B.

2. All output circuits are power

limited to NFPA 70 per NEC

760.

3. Electrical Ratings:

Output Zone Supervisory:

8mA max @ 24VDC

Output Zone Active:

25V — 25 watts max / zone

70V — 30 watts max / zone

4. EOL resistor, 24k ohms,

1 watt , 5%, P/N 140-033771.

5. Polarity shown in active

state.

6. For a list of Compatible

Notification Appliances, refer

to P/N 315-096363.

7. Refer to CAB1/CAB1R (P/N

315-0330007) and CAB2-BB/

CAB3-BB (P/N 315-033009)

Installation Instructions for

details on the separation of

power limited and non-

power limited wiring.

8. Positive and negative ground

fault detected at <40K for

terminals 1 - 16.

Figure 6

ZIC-8B Single-Channel Audio Wiring

Table of contents

Other Siemens Touch Panel manuals

Siemens

Siemens SIMATIC KP400 Comfort User manual

Siemens

Siemens SIMATIC INOX Series Administrator guide

Siemens

Siemens Simatic PC Panel PC 870 Installation manual

Siemens

Siemens Panel PC 670 Technical Document

Siemens

Siemens SIMATIC SCD1900 User manual

Siemens

Siemens SIMATIC OP 77B User manual

Siemens

Siemens SIMATIC TP 270 User manual

Siemens

Siemens SIMATIC WinCC V11 User guide

Siemens

Siemens SIMATIC 870 V2 User manual

Siemens

Siemens SIMATIC Panel PC IL 77 User manual

Siemens

Siemens 670 V2 User manual

Siemens

Siemens SIMATIC LS120 User manual

Siemens

Siemens PC 677B User manual

Siemens

Siemens UP 588 User manual

Siemens

Siemens SIMATIC Panel PC IL 77 User manual

Siemens

Siemens 6AV3991-1AJ02-0AB0 Technical Document

Siemens

Siemens SIMATIC 677 User manual

Siemens

Siemens 5WG1205-2AB21 User manual

Siemens

Siemens Simatic PC Panel PC 870 Technical Document

Siemens

Siemens POL8T5.70/STD User guide

Siemens

Siemens Climatix POL8T1.4X/STD Operator's manual

Siemens

Siemens SIMATIC PC 670 V2 User manual

Siemens

Siemens SIMATIC 677 User manual

Siemens

Siemens POL8T2.40/STD Operator's manual

Popular Touch Panel manuals by other brands

FlowLine

FlowLine Data loop quick start

ALPEX

ALPEX AEx-8 P Series user manual

Ltech

Ltech E5S manual

Harman

Harman AMX MODERO S MSD-701-L2 quick start guide

Acnodes

Acnodes PC 1150 installation guide

AIS

AIS IP10IA99 series user guide

IBASE Technology

IBASE Technology ASTUT-152-RE1S user manual

YASKAWA

YASKAWA TP 610C manual

B&R

B&R Power Panel C Series user manual

Beijer Electronics

Beijer Electronics X2 control Hardware and installation manual

AXIOMTEK

AXIOMTEK GOT321W-521 user manual

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Operation manual

Qomo

Qomo QIT1386 user manual

DFI

DFI KS104-CD user manual

AMX

AMX AXP-PPC Dimensional drawing

Sartorius

Sartorius X3 PR 5410 operating manual

AMX

AMX Modero X Series quick start guide

Advantech

Advantech TPC-30 Series user manual