Siemens HEATWELL RDE Series Operator's manual

Siemens Building Technologies

RDE… Simple Instructions.

Front Panel: Programming Buttons

Programmed Heating

Constant Heating (Manual)

Economy Heating Temperature or OFF

Controls under the cover on the right hand side.

TO SET CLOCK

Press the Clock Button

Adjust to the current time, using the plus and minus buttons

(please note: the clock is in 24 hour time)

Once the time has set push the enter button or wait for 5 seconds.

(The controller will then return to the main screen)

TO SET THE DAY

The day is the Black box’s on the top of the screen with numbers in, Mon= day 1, Tue= day 2 etc

Press the 1… 7 Button, the day it is currently on will flash

Adjust the day by using the plus and minus buttons

Once the correct day is chosen push the enter button or wait for 5 seconds.

TO SET THE HEATING TEMPERATURE

The Heating temperature is the temperature you would like to warm the room up to.

Press the sun button.

Adjust to the required temperature using the plus and minus buttons

Once the desired temperature is chosen push the enter button or wait for 5 seconds.

TO SET THE ECONOMY TEMPERATURE

The Economy Temperature is the lowest temperature you ever want the floor to get to at anytime.

Press the moon button.

Adjust to the required temperature using the plus and minus buttons

Once the desired temperature is chosen push the enter button or wait for 5 seconds.

(This can be made an OFF position by taking the temperature down to OFF. You need to hold the Minus

button for 5 seconds after you get down to the temperature 5 degrees)

For further information contact your underfloor heating installer.

__________________________________________________________

Or contact Siemens NZ Ltd, 09 580 5500 – HVAC Technical Support.

0508 HEATWELL

0508 432 893

Siemens Building Technologies

RDE… Simple Instructions continued.

PROGRAMMING

TO SET THE DAILY TIMES

Move the front vertical slider to the AUTO position.

Press the Blocks button under the panel.

The time setting starts from day 1 at 00.00 in the morning.

The screen will look like this,

Press the moon button for economy heating periods, after you have pushed the moon button you will

automatically advance to the next time period.

Press the sun button for the ON periods, after you have pushed the sun button you will automatically advance

to the next time period.

EXAMPLE - Below is an example of a screen and the heating periods.

If you make a mistake press the blocks button and start again.

When the desired Settings are made push the Enter button , this will save the changes and move you

to day 2 to enter the settings.

Repeat the above steps for days 2-7.

When you are finished, push the Blocks button to return to the main screen.

To check your programs push the blocks button and using the 1…7 button move through the days.

Batteries. (Battery symbol)

If you see the battery symbol on your screen (in the bottom left hand corner) it means your batteries are

getting flat. Remove the batteries and replace with Triple A (AAA) Alkaline batteries. (The batteries are found

in the bottom left hand corner, they slide down in a case) Please note: not all units have batteries.

For further information contact your underfloor heating installer.

__________________________________________________________

Or contact Siemens NZ Ltd, 09 580 5500 – HVAC Technical Support.

0508 HEATWELL

0508 432 893

Table of contents

Other Siemens Temperature Controllers manuals

Siemens

Siemens QAA2290.EWSC User manual

Siemens

Siemens 1000 series User manual

Siemens

Siemens RLE162 User manual

Siemens

Siemens RDF110 User manual

Siemens

Siemens SITRANS TSinse rt Administrator guide

Siemens

Siemens REV23 User manual

Siemens

Siemens RDD10.1DHW User manual

Siemens

Siemens REA23.03RF User manual

Siemens

Siemens REV24 User manual

Siemens

Siemens RDX42.22U Owner's manual

Siemens

Siemens SITRANS TS100 Administrator guide

Siemens

Siemens 5TC9774-4 Series User manual

Siemens

Siemens RLA162 User manual

Siemens

Siemens SITRANS TSinse rt Administrator guide

Siemens

Siemens RDX33 Series User manual

Siemens

Siemens QMX3.P37 User manual

Siemens

Siemens REV24 User manual

Siemens

Siemens i-system UP 237K Service manual

Siemens

Siemens QAA73.110 User manual

Siemens

Siemens RDF300 Series Operator's manual

Siemens

Siemens REA23 User manual

Siemens

Siemens RLE132 User manual

Siemens

Siemens RDJ10RF/SET User manual

Siemens

Siemens RDH10RF/SET User manual

Popular Temperature Controllers manuals by other brands

Swegon

Swegon LUNAd MB Instructions for use

Lucky Reptile

Lucky Reptile Thermo Control II Operation instructions

SENSORMETRIX

SENSORMETRIX Argon 100 manual

Fuji Electric

Fuji Electric PXE4 instruction manual

Yuyao gongyi

Yuyao gongyi XMT-808 series Operation manual

Selec

Selec TC544C user guide

P.W. KEY

P.W. KEY rt-208gt operating manual

Future Design

Future Design FDC-9200 user manual

BH Thermal

BH Thermal BriskONE owner's manual

Omron

Omron E5EX-H manual

West Control Solutions

West Control Solutions KS 45 Operation Notes

MCS

MCS RITC-15B Operator's manual

SMC Networks

SMC Networks Thermo-con INR-244-639 Operation manual

eltherm

eltherm Ex-TC It Series operating instructions

Omron

Omron C200H-TV Series Operation manual

industrie technik

industrie technik CA1 instructions

KRAL

KRAL EET 32 operating instructions

dixell

dixell XR420C Installing and operating instructions