Siemens Flange Mount Kit User manual

DPD01156B Siemens Industry, Inc.

Flange Mount Kits for Frames FS4 to FS7

Mounting Instructions

General

Using the optional Flange Mounting Kit, you can mount your drive through the cabinet wall or similar surface

so that the control unit of the drive remains inside the cabinet.

The correct installation of the Flange Mounting Kit might affect the IP or UL protection class of the drive. If

your drive is protected according to Type12/IP54, or your drive is supplied with flange option at the factory,

you only need to install the collars, as instructed. However, the power module of a Type1/IP21-protected drive

will only become protected according to Type12/IP54 on the rear side (see figure below), if all parts of the

flange mounting kit are installed properly. The need for this has to be evaluated and these actions are

explained in this guide.

Figure 1. Example of the flange mounting.

BT9070

CABINET WALL

OR SIMILAR

CABINET

WALL OR

SIMILAR

REAR

TYPE 12/

IP54

IP00

FRONT

Siemens Industry, Inc. DPD01156B

Flange Mount - Frames FS4 - FS7

Figures 2. - 5. present the dimensions of the drives with the flange mount option. Figure 6. present the

dimensions of the opening and the drive outline with the flange.

Use the embossed holes or self-clinching nuts in the back plate when mounting the drive to ensure proper

sealing.

Figure 2. FS4, flange mount, dimensions.

152 (5.98)

15 (.59)

122 (4.80)

Ø7(.27)

285 (11.22) 24 (.94)

113 (4.44)

357 (14.05)

341 (13.42)

101.6 (4)

72.1 (2.83)

18.5 (.72)

32.8 (1.29)

39 (1.53)

77 (3.03)

190 (7.48)

134 (5.27)

128 (5.03)

186.9 (7.35)9 (.35)

BT11134

DPD01156B Siemens Industry, Inc.

Figure 3. FS5, flange mount, dimensions.

BT11132

Ø7(.27)

436 (17.16)

454.1 (17.87)

262.5 (10.33)

145 (5.70)

144 (5.66)

150 (5.90)

169 (6.65)

9 (.35)

13 (.51) 382 (15.03) 24 (.94)

39 (1.53)

33 (1.29)

27,5 (1.08)

100 (3.93)

214 (8.42)

114 (4.48)

11.5 (.45)

72.2 (2.84)

145 (5.70)

101.9 (4.01)

12 (.47)

Siemens Industry, Inc. DPD01156B

Figure 4. FS6, flange mount, dimensions

DPD01156B Siemens Industry, Inc.

Figure 5. FS7, flange mount, dimensions

Siemens Industry, Inc. DPD01156B

Figure 6. Flange mount cutout and drive outline dimensions for FS4 to FS7.

Table 1. Flange mount cutout dimensions for FS4 to FS7 in mm (in).

Frame A B C D E

FS4 315 (12.40) 137 (5.39) 357 (14.05) 152 (5.98) 24 (.94)

FS5 408 (16.06) 152 (5.98) 454 (17.87) 169 (6.65) 23 (.90)

FS6 541 (21.29) 203 (7.99) 580 (22.83) 220 (8.66) 23 (.90)

FS7 655 (25.78) 240 (9.44) 680 (26.77) 286 (11.25) 13 (.51)

11136.emf

flange

cutout

outline

DPD01156B Siemens Industry, Inc.

Flange Mount Kit for Frame FS4

The kit consists of:

1. Top collar, (70CMR00281)

2. Bottom collar, (70CMR00280)

3. Side collars (2 pcs), (70CMR00282)

4. Internal fan, (70CPE00132, 70CPE00056) depends on the

control unit

5. Sealing plug (3 pcs), (70CMR00324)

Additionally:

• 8 screws size 4x16 (for the top and bottom collar mounting)

• 3 screws size 4x12 (for the side collar mounting)

• 2 screws size 3.5x10 (for the bottom collar mounting)

FS4 Flange Mounting

If your drive is the Type 1/IP21-protected and there is the risk that dust or other impurities in the cooling air

might end up inside the control unit, start the mounting with actions described in the steps 1 to 4.

If this is not needed, install the flange mounting kit proceeding directly to the step 5. Note, in this case the rear

will not be according to the Type 12/IP54.

9266.emf

M3.5x10

M4x12

M4x16

Siemens Industry, Inc. DPD01156B

Remove the cover of the drive.

Lift up the I/O protection plate.

The location of the internal fan

depends on the control unit.

If you have the control unit presented

in the upper picture, slide the internal

fan into the opening with the label

facing the cabling end of the drive.

If you have the control unit presented

in the lower picture, install the internal

fan with the label facing downwards.

11147.emf

11150.emf

DPD01156B Siemens Industry, Inc.

2Connect the power wire to the power

connector. The location of the power

connector depends on the control unit.

3Remove the main fan.

11148.emf

11149.emf

9289.emf

Siemens Industry, Inc. DPD01156B

Insert the three sealing plugs into

position where indicated.

Remount the main fan carefully,

checking its position.

Attach the side collars with three

screws size 4x12. The tightening

torque for the screws is 2 Nm (17.70

lbf-in).

Important! Do not yet screw the fourth

screw in the bottom right hole.

11151.emf

9287.emf

Other Siemens Rack & Stand manuals

Siemens

Siemens FC300 User manual

Siemens

Siemens KNX GAMMA AP 258E11 User manual

Siemens

Siemens 8PQ9801-0AA00 User manual

Siemens

Siemens 3WL Series User manual

Siemens

Siemens 8PQ9802-7AA53 User manual

Siemens

Siemens 3KX3612-1B User manual

Siemens

Siemens 8PQ9800-6AA24 User manual

Siemens

Siemens 3WL/3WA/4000A User manual

Siemens

Siemens H1900 User manual

Siemens

Siemens SIPART PS2 User manual

Siemens

Siemens 3VL800-1250 User manual

Siemens

Siemens SINAMICS DCM Assembly instructions

Siemens

Siemens SENTRON 3VL160 User manual

Siemens

Siemens 8PQ9800-4AA21 User manual

Siemens

Siemens AP-220-MNT-W3 User manual

Siemens

Siemens CHBA221 Series User manual

Siemens

Siemens H1800 User manual

Siemens

Siemens Actavix ASK33 User manual

Siemens

Siemens 3VL9500-8SA40 User manual

Siemens

Siemens FDM275-O User manual

Siemens

Siemens 8PQ9800-4AA83 User manual

Siemens

Siemens 8PQ9802-8AA53 User manual

Siemens

Siemens 3KC9811-0 User manual

Siemens

Siemens 8PQ9800-3AA80 User manual

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 