Siemens SIMATIC S7-200 User manual

Siemens AG

Ethernet Gateway

for SIMATIC MPI/

PROFIBUS Driver

1 System Configuration....................................................................................................... 3

2 External Device Selection ................................................................................................ 6

3 Communication Settings .................................................................................................. 7

4 Setup Items ...................................................................................................................... 9

5 Supported Device Addresses......................................................................................... 15

6 Device Code and Address Code.................................................................................... 17

7 Error Messages.............................................................................................................. 18

Ethernet Gateway for SIMATIC MPI/PROFIBUS Driver

GP-Pro EX Device/PLC Connection Manual 2

Introduction

This manual describes how to connect the Display and the External Device (target PLC).

In this manual, the connection procedure is described in the sections identified below:

1System Configuration

This section lists the types of External

Devices and SIO that you can connect.

"1 System Configuration" (page 3)

2External Device Selection

Select the model (series) of the External

Device and its connection method.

"2 External Device Selection" (page 6)

3Communication Settings

This section shows setting examples for

communicating between the Display and

the External Device.

"3 Communication Settings" (page 7)

4Setup Items

This section describes communication

setup items on the Display.

Set the Display's communication settings

in GP Pro-EX or in off-line mode.

"4 Setup Items" (page 9)

Operation

Ethernet Gateway for SIMATIC MPI/PROFIBUS Driver

GP-Pro EX Device/PLC Connection Manual 3

1 System Configuration

The system configuration in the case when the External Device of Siemens AG and the Display are connected is

shown.

Series CPU Link I/F Communication

Method Setting Example

SIMATIC

S7-200 Series

CPU214

CPU215

CPU216

CPU221

CPU222

CPU224

CPU226

Port 0/1 on the CPU unit Ethernet (TCP) "Setting Example 1"

(page 7)

SIMATIC

S7-300 Series

CPU312IFM

CPU313

CPU314

CPU314IFM

CPU315

CPU315-2 DP

CPU316

CPU316-2 DP

CPU318-2

MPI port on the CPU

unit Ethernet (TCP) "Setting Example 1"

(page 7)

SIMATIC

S7-400 Series

CPU412-1

CPU412-2 DP

CPU413-1

CPU413-2 DP

CPU414-1

CPU414-2 DP

CPU414-3 DP

CPU416-1

CPU416-2 DP

CPU416-3 DP

CPU417-4

MPI port on the CPU

unit Ethernet (TCP) "Setting Example 1"

(page 7)

Ethernet Gateway for SIMATIC MPI/PROFIBUS Driver

GP-Pro EX Device/PLC Connection Manual 4

Connection Configuration

1:1 Connection

1:n Connection

Display External Device

Adapter

Display External Device External Device

Adapter

Maximum number of External Devices: 12

Display External Device External Device

Adapter

HUB

Maximum number of External Devices: 12

Ethernet Gateway for SIMATIC MPI/PROFIBUS Driver

GP-Pro EX Device/PLC Connection Manual 5

n:m Connection

• It is able to connect only one adapter to one Display.

Display External Device

Adapter

HUB

Maximum Display Units depends

on the External Device CPU Maximum number of Display: 12

Display External Device

Adapter

HUB

Maximum number of Display: 7 Maximum number of Display: 12

Ethernet Gateway for SIMATIC MPI/PROFIBUS Driver

GP-Pro EX Device/PLC Connection Manual 6

2 External Device Selection

Select the External Device to be connected to the Display.

Setup Items Setup Description

Number of Devices/PLCs Use an integer from 1 to 4 to enter the number of Devices/PLCs to connect to the

display.

Manufacturer Select the manufacturer of the External Device to be connected. Select "Siemens

AG".

Series

Select a model (series) of the External Device to be connected and connection

method. Select "Ethernet Gateway for SIMATIC MPI/PROFIBUS".

Check the External Device which can be connected in "Ethernet Gateway for

SIMATIC MPI/PROFIBUS" in system configuration.

"1 System Configuration" (page 3)

Port Select the Display port to be connected to the External Device. Select "Ethernet

(TCP)".

Use System Area

Check this option to synchronize the system data area of the Display and the device

(memory) of the External Device. When synchronized, you can use the External

Device’s ladder program to switch the display or display the window on the Display.

Cf. GP-Pro EX Reference Manual "LS Area (Direct Access Method

Area)"

This feature can also be set in GP-Pro EX or in the Display's offline mode.

Cf. GP-Pro EX Reference Manual "System Settings [Display Unit] -

[System Area] Settings Guide"

Cf. Maintenance/Troubleshooting Guide "Main Unit - System Area

Settings"

Ethernet Gateway for SIMATIC MPI/PROFIBUS Driver

GP-Pro EX Device/PLC Connection Manual 7

3 Communication Settings

This section provides examples of communication settings recommended by Pro-face for the Display and the

External Device.

3.1 Setting Example 1

GP-Pro EX Settings

Communication Settings

To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC].

Ethernet Gateway for SIMATIC MPI/PROFIBUS Driver

GP-Pro EX Device/PLC Connection Manual 8

Device Setting

To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]

window, select the external device and click [Settings] .

To connect multiple External Devices, from [Device-Specific Settings] in the [Device/PLC] window, click [Add

Device] to add another External Device.

External Device Settings

Use the Web Browser to access the Adapter for communication setting. Please refer to the manual of the Adapter

for more details.

1The home page, which is located at ‘http://<ip-address>’, is a basic address and navigation starting point for the

user.

2The configuration page, accessible via a link on the home page, is a configuration interface for the user. 

Before this page opens, it is necessary to enter the device name as Username (NETLink PRO) and the password

(admin if no user specified password is stored). The default password is ‘admin’.

3Enter the following settings and click [OK].

If you click the [OK] button, the inputs are checked for plausibility. You may then be shown which inputs are

incorrect and what correct input would look like at this point.

4If all entries are consistent, the changes are displayed again as they will now be stored in the adapter when you

click the 'OK' button again.

After the new parameters have been stored, the adapter is restarted to activate the new configuration.

• At delivery state the Adapter has the IP address 192.168.4.49

Setup Items Setting

Device name Name assigned to the adapter consisting of max. 20 alphanumeric characters.

Static IP address IP address that is used if DHCP is deactivated or the DHCP timeout elapses

Static subnet mask Subnet mask that is used if DHCP is deactivated or the DHCP timeout elapses

DHCP ON/OFF activate DHCP

DHCP Timeout

(seconds) 30 to 65500 seconds

Web interface ON/

OFF Web interface is ON or OFF

RFC1006 parameters not needed for communication with GP-Pro EX applications

New passwords password with up to eight characters

Ethernet Gateway for SIMATIC MPI/PROFIBUS Driver

GP-Pro EX Device/PLC Connection Manual 9

4 Setup Items

Set up the Display's communication settings in GP Pro-EX or in the Display's off-line mode.

The setting of each parameter must match that of the External Device.

"3 Communication Settings" (page 7)

4.1 GP-Pro EX Setup Items

Communication Settings

To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC].

Setup Items Setup Description

Port No. Enter a port number of the Display, using 1024 to 65535. Check into [Auto], and a port

number is set automatically.

Timeout Use an integer from 1 to 127 to enter the time (s) for which Display waits for the response

from External Device.

Retry In case of no response from the External Device, use an integer from 0 to 255 to enter how

many times the Display retransmits the command.

Wait To Send Use an integer from 0 to 255 to enter standby time (ms) for the Display from receiving

packets to transmitting next commands.

Ethernet Gateway for SIMATIC MPI/PROFIBUS Driver

GP-Pro EX Device/PLC Connection Manual 10

IP Address

Input the IP address of Gateway/Module. Search the adapter in the network and click the

[Search].

Port No. Display the port number of Gateway/Module.

Speed Set the communication speed of MPI/PROFIBUS network.

Local Node Set the node number of Display in MPI/PROFIBUS network.

Highest Node Number Set the maximum node number of MPI/PROFIBUS network.

• Refer to the GP-Pro EX Reference Manual for Indirect Device.

Cf. GP-Pro EX Reference Manual "Changing the Device/PLC at Runtime (Indirect

Device)"

Setup Items Setup Description

Other manuals for SIMATIC S7-200

This manual suits for next models

Table of contents

Other Siemens Gateway manuals

Siemens

Siemens SIMATIC PN/M-Bus LINK User manual

Siemens

Siemens SpeedStream 6500 Series User manual

Siemens

Siemens SIMATIC PN/J1939 LINK User manual

Siemens

Siemens 5935 User manual

Siemens

Siemens FDCW241 User manual

Siemens

Siemens SIMATIC IOT2050 User manual

Siemens

Siemens SCALANCE X-300 Guide

Siemens

Siemens Gigaset SE568 User manual

Siemens

Siemens GAMMA 5WG1 143-1AB01 Service manual

Siemens

Siemens A53457 Maintenance and service guide

Siemens

Siemens SIMATIC IOT2050 User manual

Siemens

Siemens Instabus/DALI Gateway N 141 User manual

Siemens

Siemens Cerberus GW-21 User manual

Siemens

Siemens NK8237 MP4.81-01 User manual

Siemens

Siemens SIRIUS 3RK3141 Series User manual

Siemens

Siemens SIMATIC User manual

Siemens

Siemens ProtoAir FPA-W44 User guide

Siemens

Siemens SCALANCE X-200 User manual

Siemens

Siemens HG 3500 V4 User manual

Siemens

Siemens FDCW221 User manual

Siemens

Siemens Tiastar LV MCC User manual

Siemens

Siemens Sinamics Connect Series User manual

Siemens

Siemens NK8237 MP4.40 Parts list manual

Siemens

Siemens SIMATIC IOT User manual

Popular Gateway manuals by other brands

LST

LST M500RFE-AS Specification sheet

Kinnex

Kinnex Media Gateway quick start guide

2N Telekomunikace

2N Telekomunikace 2N StarGate user manual

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Original instructions

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE user guide

Telsey

Telsey CPVA 500 - SIP Technical manual

RTA

RTA 460A-NNA4 Product user guide

Shaw

Shaw Gateway HDPVR user manual

ABB

ABB VSN900 Commissioning manual

Commander

Commander Pulse owner's manual

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E manual

NETGEAR

NETGEAR C6300BD installation guide

Amit

Amit CDW531AM user guide

HMS

HMS Netbiter EasyConnect EC150 user manual

Huawei

Huawei EchoLife HG620 user guide

AT&T

AT&T U-verse 3801 Replacement self-installation guide

Logic IO

Logic IO RTCU MX2 turbo Technical manual

Suttle

Suttle MediaMAX MXM-521 installation instructions