Siemens Cerberus CS1140 Guide

Cerberus®CS1140

Fire detection system

Commissioning ’Extinguishing’

EP7F

Fire & Security Products

Siemens Building Technologies Group

Data and design subject to change

without notice. / Supply subject to

availability.

ECopyright by

Siemens Building Technologies AG

Wir behalten uns alle Rechte an

diesem Dokument und an dem in ihm

dargestellten Gegenstand vor. Der

Empfänger anerkennt diese Rechte

und wird dieses Dokument nicht ohne

unsere vorgängige schriftliche

Ermächtigung ganz oder teilweise

Dritten zugänglich machen oder

ausserhalb des Zweckes verwenden,

zu dem es ihm übergeben worden ist.

We reserve all rights in this document

and in the subject thereof. By

acceptance of the document the

recipient acknowledges these rights

and undertakes not to publish the

document nor the subject thereof in

full or in part, nor to make them

available to any third party without our

prior express written authorization,

nor to use it for any purpose other

than for which it was delivered to him.

Nous nous réservons tous les droits

sur ce document, ainsi que sur l’objet

y figurant. La partie recevant ce

document reconnaît ces droits et elle

s’engage à ne pas le rendre

accessible à des tiers, même

partiellement, sans notre autorisation

écrite préalable et à ne pas

l’employer à des fins autres que

celles pour lesquelles il lui a été

remis.

Ci riserviamo ogni diritto relativo al

presente documento e sull’oggetto

illustrato in esso. La parte che riceve

il documento si impegna a non

renderlo accessibile a terzi, né per

intero né in parte, senza la nostra

previa autorizzazione scritta ed a non

usarlo per altri scopi di quello per il

quale è stato rilasciato.

07.2004

Fire & Security Products

Siemens Building Technologies Group

About this document 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1 Safety regulations 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.1 Signal words and symbols 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.2 Safety-relevant working instructions 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8 Procedure 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9 Preparation of hardware 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.1 Control module ’Extinguishing’ E3G080 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.2 Dual sector extinguishing p.c.b K5L020 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.3 Emergency operation link E3G110 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.4 Operating unit ’Extinguishing’ B3Q440 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.5 Control terminal AlgoPilot B3Q460/48x, B3Q660/68x 19. . . . . . . . . . . . . . . . . . . .

10 Calibration on E3G080 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10.1 Line voltages E3G080 from index y’AB’ (Type FM) 19. . . . . . . . . . . . . . . . . . . . .

10.2 Automatic calibration 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11 User function 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11.1 Notes for parameterization ’Extinguishing’ (E3G080) via AlgoWorks 21. . . . . . .

12 Performance checks 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12.1 Performance check in ’Normal operating condition’ 23. . . . . . . . . . . . . . . . . . . . .

12.2 Individual control functions 25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12.3 Notes 25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13 Overview of operating functions 26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13.1 Functions ’Extinguishing control −> REVISION’ and ’Extinguishing control −>

TEST’ 26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13.2 AlgoPilot ’CT11’ list of functions ’SECTION’ 26. . . . . . . . . . . . . . . . . . . . . . . . . . . .

14 Error diagnosis 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

14.1 Fault identification at the operation unit extinguishing B3Q440 27. . . . . . . . . . . .

14.2 Identification of fault at the E3G080 28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Fire & Security Products

Siemens Building Technologies Group

07.2004

005109_b_en-0

Fire & Security Products

Siemens Building Technologies Group 07.2004

About this document

Purpose of the document

This document describes the commissioning of the hardware modules of the control units

CS1140/45 with extinguishing section. The consistent observance of the instructions ensures a

trouble-free and safe application.

Scope

This document contains information valid for the software variant EP7F.

Target group

Group of persons Activity Qualification

Commissioning personnel The configuration of the products, devices or systems

for specific customers at the place of installation.

They check serviceability and officially clear the product,

device or system for use by the operator / customer.

They are also responsible for trouble-shooting.

They have had the training appropriate to their func−tion

and to the commissioning of the products, de-vices or

systems and have attended the technical training cour-

ses for commissioning personnel.

Reference documents

Information in Document

1260 Description of hardware plug−in modules (CS1140 ’Modular’)

004665 Operating instructions AlgoPilot B3Q4..

004598 Operating instructions AlgoPilot B3Q6..

005590 Operating instructions ’Extinguishing’ with AlgoPilot B3Q4..

005113 Operating instructions ’Extinguishing’ with AlgoPilot B3Q6..

005377 Compact control unit CI1145

006516 Inscription strip templates for indication and operation equipment

Operational and safety regulations

iBefore persons begin work on the system, they must have read and understood the related

documents, in particular Chapter 1 ’Safety regulations’.

005109_b_en-0

Fire & Security Products

Siemens Building Technologies Group 07.2004

Disregard of the safety regulations

Before they are delivered, the products are tested to ensure they function correctly when used

properly. Siemens disclaims all liability for damage or injuries caused by the incorrect applica-

tion of the instructions or disregard of warnings of danger contained in the documentation. This

applies in particular to:

ÜPersonal injuries or damage caused by improper use and incorrect use;

ÜPersonal injuries or damage caused by disregarding safety instructions in the documentation

or on the product;

ÜPersonal injuries or damage caused by poor maintenance or a lack of maintenance.

Standard symbols

(...) Additional information

’.....’ Definition of names

.Details see page ...., or document .....

Document identification

Position Signification

Title page – System names

– Product type

– Purpose of the document

Last page bottom left

bottom right

– Document number consists of: Language, number, index

– Date of version

– Manual

– Register

Modification index

Version Date Brief description

e5109a 05. 2003 Commissioning of the hardware Extinguishing, Product release version EP7F

005109_d_en_-- 07.2004 Table Line voltages, Indication Loss of extinguishing agent, several minor chan-

ges

Training

Siemens Fire & Security Products offers a comprehensive training program for all products. In-

formation on training courses can be found in the Siemens intranet under http://web4.cerbe-

rus.ch/.

Download

The most recently released technical documents for customers can be found in the Siemens

intranet under http://web4.cerberus.ch/.

005109_b_en-1

Fire & Security Products

Siemens Building Technologies Group 07.2004

1 Safety regulations

This chapter describes the danger levels and the relevant safety regulations applicable for the

use of the Cerberusproducts. Please read the work instructions as well as the chapter ’About

this document’ before beginning with the work.

1.1 Signal words and symbols

1.1.1 Signal words and their meaning

The danger level −that is, the severety and probability of danger −is indicated by the signal

words listed below. Non-observance may lead to the conseqences indicated:

DANGER

Imminent danger!

DMay cause danger to life or serious bodily injury!

WARNING

Dangerous situation!

DMay cause serious bodily harm!

CAUTION

May cause dangerous situations!

DMay cause light injuries!

NOTE

Possibly harmful situation!

DMay cause damage to the product or to objects in the immediate vicinity of the product!

1.1.2 Symbols and their meaning

The symbols listed below indicate the nature and origin of danger.

General danger

Electrical voltage

Example for a danger warning

DANGER External voltage

Disconnect the module from the power supply.

1.1.3 Classification and meaning of additional symbols

iTips and information.

005109_b_en-1

Fire & Security Products

Siemens Building Technologies Group 07.2004

1.2 Safety-relevant working instructions

Country-specific standards

The products are developed and produced in compliance with the relevant international and Eu-

ropean safety standards. Should additional country-specific, local safety standards or regula-

tions concerning project planning, assembly, installation, operation and disposal of the product

apply in the place of operation, then these standards or regulations must also be taken into ac-

count in addition to the safety regulations mentioned in the product documentation.

Electrical installations

DANGER Work on electrical installations

Work on electrical installations may only be carried out by qualified electricians or instructed

persons working under the guidance and supervision of a qualified electrician, in accor-

dance with the electrotechnical regulations.

DControl units must be disconnected from the power supply during commissioning or mainte-

nance work.

DTerminals with an external voltage supply must be provided with a sign ’DANGER −External

voltage’.

DMains leads to the control unit must be installed separately and provided with a clearly mar-

ked fuse.

DEarthing must be carried out in compliance with local safety regulations.

DWhen work is carried out in explosion−hazardous areas, the appropriate safety precautions

must be taken.

Assembly, installation, commissioning and inspection work

DIf any tools such as ladders are required, safe and suitable devices must be used.

DPrevention of spurious tripping of the remote transmission must be assured.

DAlways inform the plant fire brigade before testing the remote transmission.

DThe activation of fire control installations for test purposes must not cause damage to the sy-

stem or parts thereof.

DFire control installations must only be activated after the test has been completed and the

system has been handed over to the customer.

DThird party systems or devices must only be activated in the presence of the responsible per-

son.

DWhen work on management stations and system terminals is performed, the safety regula-

tions of the connected sub-systems must be observed. This especially applies when swit-

ching-off system components.

DIn the case of extinguishing systems, always use the ”General installation instructions” as a

guideline. This guideline is available on request.

Testing the product operability

DEvacuate and cordon off extinguishing sector.

DInform people about the possibility of occurring fog and noise.

DInform people before testing alarm devices; take the possibility of panic reactions into ac-

count.

DInform the alarm and fault receiving stations connected to the system before running the

tests.

005109_b_en-1

Fire & Security Products

Siemens Building Technologies Group 07.2004

Modifications to the system design and the product

Modifications to a system or to individual products may cause faults or malfunctioning. Please

request written approval from us and the relevant authorities concerning intended system modi-

fications and system extensions.

Modules and spare parts

DLocally procured modules and spare parts must comply with the technical specifications laid

down by the manufacturer. This compliance is always ensured for original spare parts sup-

plied by us.

DOnly use fuses with the specific fuse characteristics.

DWrong battery types and improper battery exchange may introduce the danger of explosion.

Only use the specified battery type or an equivalent battery type recommended by the manu-

facturer.

DBatteries require environmentally safe disposal. They must be handed in at the local collec-

ting points.

DPlease take into account that the extinguishing agent cylinders are pressurized and must be

exchanged in compliance with the local safety regulations.

005109_b_en−2

Fire & Security Products

Siemens Building Technologies Group 07.2004

2 Procedure

Step Detail in-

formation

chapter

1. Preparation of electronic modules

îSet switch and resistors on E3G080

îCalibration control lines on K5L020

îTo shunt line links on E3G110

îSet switches and resistors on B3Q440

îInsert inscription strips

3.1

3.2

3.3

3.4

3.5

2. Initial switch-on

îFirst set switch ’S1’ on the E3G080 to ’ON’

Note: ’S1’ −> ’ON’ = hardware and software blocking of all E3G080 outputs

3.1

3. Measure voltage at E3G080

Check voltage of all peripheral equipment connected to the E3G080

îEnsure rest potential throughout the area

4.1

4. Initialize automatic calibration function on E3G080

This function calibrates the valve current and registers and stores which li-

nes are connected.

First ensure that:

−no signalling contact is in active mode

−all lines are connected including the line termination

−the impedance range chosen for the valve lines is correct (’R60/61’)

îPress key ’S4’ (set switch ’S1’ to ON)

Meaning of LEDs H1....H4 on E3G080

3.1

4.2

5. Performance check

First ensure, that the user functions have been set correctly

îCarry out ’Normal operating condition’ control function

îCarry out individual control functions

Note: −Functions ’Extinguishing REVISION’ und ’Extinguishing TEST’

−Extent of available functions in SECTION list

5.1

6.1

6.2

7.1

7.2

Important

In some countries, with CO2-extinguishing systems with a risk to life (CO2-concentration

>5Vol%) a so-called ’Concidence of the vital functions is required (vital functions must be

guaranteed).

Examples:

Dan electrical and a mechanical/pneumatic delay device in AND operation

Üfor this purpose the E3G080 has 2 different valve activating outputs

DCompulsory pre-warning also functions in the event of a fault (e.g. caused by lightning etc.)

Üuse pneumatic sirens

Dautomatic activation of extinguishing is guaranteed even if the main central processing unit

malfunctions

Üuse optional emergency operation link E3G110

etc.

iWhen commissioning, ensure that the local requirements are fully complied with. If the sys-

tem operator asks for a concept which deviates from the regulations, then he must bear the

responsibility.

Other manuals for Cerberus CS1140

This manual suits for next models

Table of contents

Other Siemens Fire Alarm manuals

Siemens

Siemens FDM223-Ex User manual

Siemens

Siemens DBS721 User manual

Siemens

Siemens HFPT-11 Service manual

Siemens

Siemens MH-5 Series Service manual

Siemens

Siemens SFPO-11 Service manual

Siemens

Siemens CZM-4 User manual

Siemens

Siemens FireSeeker FS-100 User manual

Siemens

Siemens FS720 Series Guide

Siemens

Siemens FCM2041-U3 User manual

Siemens

Siemens AnalogPLUS DB1131A User manual

Siemens

Siemens SSD-C User manual

Siemens

Siemens FP-11 FirePrint Reference manual

Siemens

Siemens FDCW221 User manual

Siemens

Siemens MH-5 Series Service manual

Siemens

Siemens Synova FC330A User manual

Siemens

Siemens FC901 User guide

Siemens

Siemens FC700A Guide

Siemens

Siemens HMS-SZ User manual

Siemens

Siemens MSI-30B User manual

Siemens

Siemens Cerberus PRO FS720 User manual

Siemens

Siemens FDOOT241-9 User manual

Siemens

Siemens FT2040 Instruction Manual

Siemens

Siemens FDOOT221 User manual

Siemens

Siemens FC700A Technical manual

Popular Fire Alarm manuals by other brands

Zeta Alarm Systems

Zeta Alarm Systems INFINITY ID2 installation manual

System Sensor

System Sensor 22051TLE-RF-26 Installation and maintenance instructions

Pittway

Pittway Notifier AM2020 troubleshooting guide

Ampac

Ampac ZoneSense user manual

Kidde

Kidde VM-1 Technical reference manual

LST

LST SIM016-3 Specification sheet

Fireboy- Xintex

Fireboy- Xintex FBD-MZ Owner's Manual & Installation Instructions

bolid

bolid S2000-IP-03 instruction manual

GST

GST DI-9204 Installation

E2S

E2S BExTBG05D instruction manual

Notifier

Notifier UZC-256 installation manual

Fire-Lite Alarms

Fire-Lite Alarms MS-2 instructions

hyfire

hyfire HY5000 Series install guide

FlameStop

FlameStop PFSIFP8 Installation and operation manual

Radionics

Radionics Radionics 9124 user guide

UniPOS

UniPOS FD 7120 instruction manual

FIREWOLF

FIREWOLF FW-C01224 owner's manual

Ziton

Ziton ZP787-3 Installation sheet