Siemens HTRI-S User manual

Siemens Building Technologies

Fire Safety

P/N 315-033300-2

Figure 1

HTRI Module

INTRODUCTION The SIEMENS Model HTRI Series Addressable

odules, shown in Figure 1, interface direct

shorting devices to the FireFinder-XLS Syste s

DLC loop circuit.

The HTRI odules are available in three odels.

The HTRI-S and HTRI-R can onitor a nor ally

open or closed dry contact. The HTRI-S can only

onitor and report the status of the contact,

while the HTRI-R incorporates an addressable

For C relay. The HTRI-D is a dual input odule

that supervises and onitors two sets of

dry contacts.

PROGRAMMING Refer to Figure 2 to locate the opening on the HTRI cover that allows access to the

progra ing holes which are on the HTRI printed circuit board.

To connect the HTRI to the

DPU Progra er/Tester,

insert the plug fro the DPU

cable provided with the

Progra er/Tester into the

opening on the front of the

HTRI. Be sure to insert the

locating tab on the plug into

the slot for the locating tab on

the HTRI as shown in Figure 2.

To prevent potential damage

to the DPU DO NOT connect

an HTRI to the DPU until at

least one wire is removed

from terminals 1 or 2 of the

HTRI.

Figure 2

Connecting The DPU Plug

Addressable Switch Interface Modules

Installation Instructions

Models HTRI-S / HTRI-D / HTRI-R

LOCATING

TAB

SLOT FOR

LOCATING TAB

PROGRAMMING

HOLES

HTRI-S/-D/-R

MODULE

PLUG FROM

DPU

PROGRAMMER/

TESTER

INSTRUCTIONS

Siemens Building Technologies

Fire Safety

P/N 315-033300-22

(Refer to Figure 3.) Follow the instructions in the DPU Manual (P/N 315-033260) to

progra the HTRI to the desired address. Record the device address on the label

located on the HTRI front panel. The HTRI can now be installed and wired to the

syste .

WIRING (Refer to Figures 4 -9 ) Refer to the appropriate wiring diagra below and wire the

addressable interface odule accordingly.

Recommended wire size 18 AWG minimum

14 AWG maximum

Wire larger than 14 AWG can damage the connector.

Power Li ited Wiring In co pliance with NEC Article 760, all power li ited fire protective signaling conduc-

tors ust be separated a ini u of ¼ inch fro all of the

following ite s located within an outlet box:

 electric light

power

 Class 1 or non-power li ited fire protective signaling conductors

To eet the above the require ents, the following guidelines must be observed

when installing this interface odule.

If power limited wiring is not used within this outlet box, then these guidelines do

not apply. In that case, be

sure to follow standard

wiring practices.

HTRI-R Control Module The HTRI-R Control Module

Barrier ust be used when

the HTRI-R relay contacts are

connected to non-power

li ited lines. Install the

ther al plastic barrier

diagonally into the backbox

to create two separate

co part ents within the

backbox to separate the

wires, as shown in Figure 4.

Figure 3

Wiring Switches

Figure 4

Inst lling the HTRI-R Control Module B rrier

Barrier

N TES:

1. There can be any number of normally closed or normally open switches.

2. The end of line resistor must be located at the last switch.

3. Do not wire a normally closed switch across the end of line resistor.

4. nly for use with security and status applications.

5. Do not use N. . switches for security applications.

NORMALLY OPEN SWITCHES

(SEE NOTES 2, 3 AND 5)

END OF LINE

RESISTOR

3.6K, 1/4W

NORMALLY CLOSED SWITCHES

(SEE NOTE 4)

ENDOFLINE

RESISTOR

3.6K, 1/4W

BACKBOX

TABS

FACE

OUT

4.5 in

2.0 in

2.5 in

0.375 in

5.25 in

3.25 in

1.187 in

0.75 in

USE P/N 330-096393

FOR DOUBLE GANG BOX

USE P/N 330-096384

FOR 4-INCH SWITCHBOX

Siemens Building Technologies

Fire Safety

P/N 315-033300-23

Wiring Entering Outlet Box All power li ited wiring ust enter the outlet box separately fro the electric light,

power, Class 1, or non-powered li ited fire protection signaling conductors. For the

TRI-R, wiring to ter inal block positions 1, 2, 3, 4, and 5 ust enter the outlet box

separately fro ter inals 6, 7, and 8.

Minimize the length of wire entering the outlet box.

WIRING AT THE TERMINAL BLOCKS

Power Li ited Wiring (Refer to Figure 5) Wiring to positions

1, 2, 3, 4, and 5 is power li ited.

Non-Power Li ited Wiring Wiring to positions 6, 7, and 8 is considered

non-power li ited.

Ground shield ONLY at the specified

location on the Control Panel.

NOTES:

1. All supervised switches

must be held closed and/or

open for at least a quarter of

a second to guarantee

detection.

2. End of line device: 3.6K, 1/4W

resistor, P/N 140-820185. For

Canadian applications, use

Model EL-33 with 3.6K, 1/4W

resistor.

3. HTRI is polarity insensitive.

Line 1 and Line 2 can be

either line of the loop.

4. Electrical ratings:

Voltage maximum: 30 VDC

Current maximum:

1mA during polling

5. Supervised switch ratings:

Voltage maximum: 27 VDC

Current maximum: 3.5mA

during polling

Contact resistance maximum:

10 ohms

Maximum cable length:

200 feet (18 AWG)

CLine to line: 0.02uF

CLine to shield: 0.04uF

Max line size: 14 AWG

Min line size: 18 AWG

6. Relay contact ratings:

4A, 125 VAC resistive

4A, 30 VDC resistive

Inductive:

3.5A, 120 VAC (0.6 P.F.)

3.0A, 30 VDC (0.6 P.F.)

2.0A, 120 VAC (0.4 P.F.)

2.0A, 120 VAC (0.35 P.F.)

2.0A, 30 VDC (0.35 P.F.)

The relay is shown in

standby condition.

Figure 5

HTRI-R Power Limited Wiring

Figure 6

HTRI-R Wiring

Figure 7

HTRI-S Wiring

Figure 8

HTRI-D Wiring

WIRES CONNECTED TO TERMINALS 1 THROUGH 5

TO ENTER/EXIT ELECTRICAL BOX OPPOSITE SIDE

FROM WIRES CONNECTED TO TERMINALS 6 THROUGH 8.

P = POWER LIMITED

N = NON-POWER LIMITED

TO NEXT

ADDRESSABLE DEVICE

LINE 1

LINE 2

END OF LINE DEVICE

SEE NOTE 2

SEE NOTE 7

RELAY CONTACTS

SEE NOTE 6

SUPERVISED SWITCH

SEE NOTES 1 AND 5

FROM CONTROL PANEL

OR FROM PREVIOUS

ADDRESSABLE DEVICE

LINE 1

LINE 2

SEE NOTE 7

TO NEXT

ADDRESSABLE DEVICE

END OF LINE DEVICE

SEE NOTE 2

NOT USED

SUPERVISED SWITCH

SEE NOTES 1 AND 5

FROM CONTROL PANEL

OR FROM PREVIOUS

ADDRESSABLE DEVICE

LINE 1

LINE 2

SEE NOTE 7

NOT USED

TO NEXT

ADDRESSABLE DEVICE

END OF LINE DEVICE

SEE NOTE 2

END OF LINE DEVICE

SEE NOTE 2

SUPERVISED SWITCH

SEE NOTES 1 AND 5

SUPERVISED SWITCH

SEE NOTES 1 AND 5

FROM CONTROL PANEL

OR FROM PREVIOUS

ADDRESSABLE DEVICE

SWITCHPLATE

5-INCHES SQUARE

(SUPPLIED)

SWITCHPLATE

5-INCHES SQUARE

(SUPPLIED)

4-INCH SQUARE BOX

2 1/8-INCHES DEEP

DOUBLE GANG BOX

3 1/2-INCHES DEEP

Siemens Building Technologies, Inc.

8 Fernwood Road

Florham Park, New Jersey 07932

Siemens Building Technologies

Fire Safety

Siemens Building Technologies, Ltd.

2 Kenview Boulevard

Brampton, ntario L6T 5E4 Canada

P/N 315-033300-2

(Contd From Previous Page):

7. Terminal 5 must be

connected to earth ground.

a. Use wire nuts to pass the

shield wire through the

electrical box with NO

connection to the device

terminal block or to local

ground.

b. Use shielded wire to

connect the switch wiring.

c. Tie the switch wiring shield

to terminal 5 or the local

earth ground.

8. For proprietary burglary

application (Refer to Figure 9):

a. Use an HTSW-1 tamper

switch to monitor the main

enclosure.

b. Monitor each HTRI-S/-R/-D

related to this application

continuously by using a

listed motion detector (to

prevent tampering).

9. In supervisory:

HTRI-S/-R draws 1mA

HTRI-D draws 1mA

Figure 9

Security Point (1076) Wiring Connections

Terminal 5 of the HTRI-S/-D/-R must be connected to a known good earth ground for

proper operation.

MOUNTING Addressable Interface SIEMENS Models HTRI-S, HTRI-D, and HTRI-R ount directly

into a (user supplied) double gang or 4 inch switchbox. Fasten the odule to the

switchbox with the switchplate using the 2 screws provided.

A red LED will blink to indicate an off-nor al input switch position and/or an internal

relay transfer.

Be sure to program the HTRI before fastening the switchplate to the unit.

Figure 10

Mounting the HTRI-S/-R/-D

TO NEXT

ADDRESSABLE DEVICE

END OF LINE DEVICE

SEE NOTES 2 AND 8

RELAY CONTACTS

SEE NOTE 6

NOTE:

WITH HTRI-S, TERMINALS

5 AND 6 ARE NOT USED.

SUPERVISED SWITCH

SEE NOTES 1, 5, 8 AND 9

FROM CONTROL PANEL

OR FROM PREVIOUS

ADDRESSABLE DEVICE

1HTRI-S/-R

LINE 1

LINE 2

SEE NOTE 7

HTRI-D

NOT USED

TO NEXT

ADDRESSABLE DEVICE

END OF LINE DEVICE

SEE NOTES 2 AND 8

END OF LINE DEVICE

SEE NOTES 2 AND 8

SUPERVISED SWITCH

SEE NOTES 1, 5, 8 AND 9

SUPERVISED SWITCH

SEE NOTES 1, 5, 8 AND 9

FROM CONTROL PANEL

OR FROM PREVIOUS

ADDRESSABLE DEVICE

LINE 1

LINE 2

SEE NOTE 7

This manual suits for next models

Other Siemens Control Unit manuals

Siemens

Siemens SIRIUS 3RW44 User manual

Siemens

Siemens SIMATIC ET 200eco PN User manual

Siemens

Siemens VAI60.15-15 User manual

Siemens

Siemens 3RK1200-0C.03-0AA2 User manual

Siemens

Siemens ASIsafe 3RK1205-0B.00 User manual

Siemens

Siemens SIMATIC EP200SP User manual

Siemens

Siemens WATCHDOG-Modul ET 200iSP User manual

Siemens

Siemens RUGGEDCOM RS900F User manual

Siemens

Siemens Simatic TI405 User manual

Siemens

Siemens SIMATIC ET 200SP User manual

Siemens

Siemens P Series User manual

Siemens

Siemens SIRIUS ACT 3SU1400-1EK10-6AA0 User manual

Siemens

Siemens SIMATIC ET 200AL User manual

Siemens

Siemens 3VL92 Series User manual

Siemens

Siemens SINUMERIK 840D sl Owner's manual

Siemens

Siemens WFZ56 Series Installation and operation manual

Siemens

Siemens SINUMERIK 808D User manual

Siemens

Siemens SIMATIC ET 200S User manual

Siemens

Siemens Logo! CM EIB User manual

Siemens

Siemens SIMATIC NET CP 5613 A2 User manual

Siemens

Siemens SIRIUS 3SF5811 A Series User manual

Siemens

Siemens CP 443-5 Extended User manual

Siemens

Siemens SIPROTEC 6MU805 User manual

Siemens

Siemens VVF Series User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual