SI Solo 2 User manual
Solo / Pro 2
Installation Instructions
110v AC Motors
Solo Pro 2Solo 2
Please use these QR
Codes to access the
updated installation
instructions and video
tutorials.
WARRANTY
Warranty
New SI products carry a standard 1- year warranty on
parts and labor.
FCC INFORMATION
This device complies with Part 15 of the FCC Results. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including that which may
cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for
CLASS B digital device, pursuant to Part 15 of FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment.
Changes or modifications not expressly approved by the manufacturer could void
the user's authority to operate the equipment.
1
INITIAL CONSIDERATIONS
Thank you for your purchase of Solo/Pro 2. The screen
is mountable outdoors, but is not waterproof. It has not
been designed to be run or left in the rain or condensing
humidity. Also avoid water spray, splash and extreme
heat or cold. Protect your Solo/Pro 2. and you can expect
years of quality use.
For a quick install it is recommended you run appropriate
wire to the installation location before installing the
screen. See the Pre-Wire sections for details.
Follow all local electrical codes when running and
terminating AC(110v) wires. It is the responsibility of the
installer to make sure AC(110v) screens are installed to
electrical safety codes.
The Short Throw material is not 100% opaque.
Light sources behind the screen may be visible in
the viewing surface.
Initial Considerations
CONTENTS
AC(110v) RTS - Parts In The Box 4
AC(110v) 485 - Parts In The Box 5
Spacer Blocks & Leveling Shims 6
Pre-Wire - AC(110v) 485 7
Installation 8
Flatten The Material At The Weight Bar 17
AC(110v) Rts 18
Programming - AC(110v) Rts 19
Pairing Another Rf Remote 21
Using Original Remote 21
Programming AC(110v) 485 - With Decoset (Incl.) 22
Screen With UAI+ / SI.FI Block Diagram 25
Control AC(110v) 485 With 3rd Party - Via Serial 28
Using 485 Motor Interface With Fontus For 3rd Party Controls -
AC Motors 29
Using 485 Motor Interface With Fontus For 3rd Party Controls -
CONTENTS
LV Motors 30
Control 485 With 3rd Party (Wet Contact) Via Fontus 31
Control 485 With 3rd Party (Dry Contact) Via Fontus 32
Control 485 With 3rd Party (IR) Via Fontus 33
Control 485 With 3rd Party (IR) Via Fontus - Programming 34
Control 485 Screens With Included Decoset Keypad 36
Control AC(110v) 485 With 3rd Party - Via IP Controller 37
Control AC(110v) 485 With 3rd Party - Via DCT 39
Mounting Accessories 41
(Purchased Separately) 41
Motor Accessories - AC(110v) Rts/ 485 (Purchased Separately)
42
Storage And Transport 43
Care And Maintenance 45
Troubleshooting 46
4
AC(110v) RTS - Parts in the Box
RF Remote
AC(110v) RTS - Parts in the Box
(2) Ceiling/Wall
Locking brackets
(6) Leveling Shims
PWR Solo/Pro 2 screen
(6) Wood
fasteners
5
(6) Leveling Shims
Coupler
AC(110v) 485 - Parts in the Box
AC(110v) 485 - Parts in the Box
(6) Wood
fasteners
Additional
accessories
required for 485
control (pg. 42)
Solo/Pro 2 screen
485
PWR
(2) Ceiling/Wall
Locking brackets
Decoset &
Interface
Bracket
SET UPPER
SET LOWER
REVERSE
UP
DOWN
STOP
485 Motor Interface
485 Motor only
6
Spacer Blocks & Leveling Shims
SPACER BLOCKS & LEVELING
SHIMS
Spacer Blocks are used to
clear an obstruction on the
wall. Connect spacer block
to each wall bracket before
installation.
Leveling Shims are used if
the ceiling or other
mounting surface is out
of level or plumb. Connect
to ceiling brackets before
installation.
7Pre-Wire - AC(110v) 485
PRE-WIRE - AC(110v) 485
1. Run 3 conductor wire/Cat 5e to the left side of
screen cassette installation location (refer to pg. 9).
To be sure you have the correct wire you can order
485 wire directly from SI.
2. Terminate the wires with the provided terminal block
as shown below.
Data +
Data -
Data ground
+
-
G
Not Used
RS485 (+)
RS485 (-)
-
-
Power from motor 7v DC
-
-
Ground
Pin 1
Pin 8
8
Proper mounting preparation will ensure a great
installation. Mounting brackets must be level to each
other, as well as plumb. They must be screwed into
structural members of some kind, such as ceiling
joists or wall studs. You may use the wood screws
provided, or other anchors (not provided) capable of
carrying the load, that is suitable to the substrate.
DO NOT MOUNT TO HOLLOW SHEET ROCK.
1. The drop is adjustable in the field between 0'' and
the MAX DROP (12'', 24'', or 36'', 2'' for short throw)
ordered for your screen. Use the drawing (refer to
pg. 7) to pick a bracket height that will allow you to
extend your screen to achieve the desired vertical
position of your viewing area.
INSTALLATION
Solo/Pro 2 - Installation
Other manuals for Solo 2
1
This manual suits for next models
2
Table of contents
Other SI Projection Screen manuals
SI
SI 7 SERIES FIXED User manual
SI
SI 5 SERIES User manual
SI
SI Dynamic 4 User manual
SI
SI Short Throw Lift Motorized Screen User manual
SI
SI Sensation Series User manual
SI
SI Nano Box User manual
SI
SI ZERO EDGE PRO User manual
SI
SI Solo 3 675 EXTERNAL INDOOR User manual
SI
SI Dynamic 2TB User manual
SI
SI FIXED 5 Series User manual
Popular Projection Screen manuals by other brands
FART PRODUKT
FART PRODUKT Standard SCREEN Installation instruction
Draper
Draper E Series Installation & operating instructions
Elite Screens
Elite Screens Elite Tripod Series user guide
Laarhoven
Laarhoven Companion II General assembly instructions
Renogy
Renogy RMS-LFPS-US manual
Da-Lite
Da-Lite ExecutiveElectrol Instruction book
