Shure AD1 User manual
1/24
AD1 -- Bodypack Transmitter
WARNING
• Battery packs may explode or release toxic materials. Risk of fire or burns. Do not open, crush, modify, disas
semble, heat above 140°F (60°C), or incinerate.
•Follow instructions from manufacturer
•Only use Shure charger to recharge Shure rechargeable batteries
•WARNING: Danger of explosion if battery incorrectly replaced. Replace only with same or equivalent type.
•Never put batteries in mouth. If swallowed, contact your physician or local poison control center
•Do not short circuit; may cause burns or catch fire
•Do not charge or use battery packs other than Shure rechargeable batteries
•Dispose of battery packs properly. Check with local vendor for proper disposal of used battery packs.
•Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or
the like
WARNING: Danger of explosion if incorrect battery replaced. Operate only with AA batteries.
Note: Use only with the included power supply or a Shure-approved equivalent.
Please follow your regional recycling scheme for batteries, packaging, and electronic waste.
WARNING: This product contains a chemical known to the State of California to cause cancer and birth defects or
other reproductive harm.
低功率電波輻射性電機管理辦法
第十二條
經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計
之特性及功能。第十四條
低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時
方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學
及醫療用電波輻射性電機設備之干擾。
AD1 Axient Digital Bodypack Transmitter
AD series bodypack transmitters deliver impeccable audio quality and RF performance with wide-tuning, High
Density (HD) mode, and encryption. The transmitter features durable metal construction, AA or SB900A recharge
able power (with dockable charging), and TA4 or LEMO3 connector options.
Shure Incorporated
2/24
Features
Performance
•20 Hz to 20 kHz range with flat frequency response
•Automatic input staging optimizes gain setting
•AES 256-bit encryption-enabled for secure transmission
•>120 dB dynamic range
•100 meter (300 feet) line-of-sight operating range
•Selectable modulation modes optimize performance for spectral efficiency
◦ Standard – optimal coverage, low latency
◦ High density – dramatic increase in max system channel count
•Built-in tone generator and RF markers to facilitate walk-testing
•Switchable Power Levels = 2/10/35 mW (region dependent)
•Frequency Diversity selection using two bodypacks
Design
•TA4 or LEMO3 audio connector option
•Backlit LCD with easy to navigate menu and controls
•Rugged metal construction
•Flexible ¼ wave antenna
•Menu and power lockout
Power
•Over 8 hours continuous use with 2 x AA alkaline batteries
•Shure SB900A lithium-ion rechargeable battery provides extended battery life, precision metering, and zero
memory effect
•External charging contacts for docked charging
Included Components
AA alkaline batteries (2) 80B8201
¼ wave antenna Varies by Region
Threaded TAF4 adapter WA340
Zipper bag 26A13
Belt clip 44A12547
Optional Accessories
Bodypack rechargeable lithium-ion battery SB900A
Shure Incorporated
3/24
Y-Cable for bodypack transmitters AXT652
LEMO Y-cable for bodypack transmitters AXT652LEMO3
Instrument cable WA302
Replacement belt clip 44A12547
Instrument cable with right angle 1/4" connector WA304
Mute Switch for Bodypack WA661
Mute Switch for 2 Bodypacks WA662
AD1 Transmitter Overview
①RF Antenna
For RF signal transmission.
②Display
View menu screens and settings. Press any control button to activate the backlight.
③Infrared (IR) Port
Align with the receiver IR port during an IR Sync for automated transmitter tuning and setup.
④Control Buttons
Use to navigate through parameter menus and to change settings.
⑤Battery Compartment
Requires two AA batteries or Shure SB900A rechargeable battery.
⑥AA Battery Adapter
Use to secure AA batteries. Remove when using a Shure SB900A battery.
⑦SMA Connector
Connection point for RF antenna.
⑧Power Switch
Powers the unit on or off.
⑨Power LED
•Green = unit is powered on
•Red = low battery, Mute Mode enabled, input overload, or battery error (see Troubleshooting)
Shure Incorporated
4/24
⑩Input Jack
Connects to a 4-Pin Mini Connector (TA4F) microphone or instrument cable.
Note: A LEMO connector model variation of this transmitter is available.
Transmitter Controls
Use the controls to navigate through parameter menus and change values.
exit Acts as a 'back' button to return to previous menus or parameters without confirming a value
change
enter Enters menu screens and confirms parameter changes
∨∧ Use to scroll through menu screens and to change parameter values
Tip: Use the following control shortcuts for quick set up:
•Hold the ∧button while powering-on to lock or unlock the transmitter controls
•Hold the exit button while powering-on to set the transmitter RF output to mute
Shure Incorporated
5/24
Locking the Interface
Lock transmitter interface controls to prevent accidental or unauthorized changes to parameters. The lock icon ap
pears on the home screen when the interface lock is enabled.
1. From the Utilities menu, navigate to Locks and select one of the following lock options:
◦None: The controls are unlocked
◦Power: The power switch is locked
◦Menu: The menu parameters are locked
◦All: The power switch and menu parameters are locked
2. Press enter to save.
Tip: To quickly unlock a transmitter: Press enter twice, select None, and press enter.
Home Screen Display
The home screen shows transmitter information and status.
Tip: There are four options to choose the information shown on the home screen. Use the arrow buttons to select
one of the following choices:
•Name
•Frequency Setting
•Group (G) and Channel (C)
•Device ID
The following icons appear to indicate transmitter settings:
Battery runtime in hours and minutes or bar display
Key: Displayed when encryption is enabled
Lock: Displayed when controls are locked. Icon will
flash if access is attempted to a locked control (power
or menu).
STD: Standard Transmission Mode
HD: High Density Transmission Mode
Shure Incorporated
6/24
Box: When the box has an "x", Mute Mode is on and
engaged. If the box is empty, Mute Mode is on, but not
engaged.
Battery Installation
①Accessing the Battery
Compartment
Press the side tabs on the bodypack and open the battery door as shown to ac
cess the battery compartment.
②Installing Batteries •AA Batteries: Place batteries (note polarity markings) and AA Adaptor as
shown and close the door
•Shure SB900A Battery: Place battery as shown (note polarity markings). Re
move the AA adapter and set it aside. Close the door to secure the battery.
Note: If using AA batteries, set the battery type using the transmitter menu.
Setting the AA Battery Type
To ensure accurate display of transmitter runtime, set the battery type in the transmitter menu to match the in
stalled AA battery type.
Note: If a Shure SB900A rechargeable battery is installed, selecting a battery type is not necessary and the battery
type will display Shure.
1. Navigate to the Utilities and select Battery.
2. Use the ▼▲ buttons to select the installed battery type:
◦Alkaline = Alkaline
◦NiMH = Nickel Metal Hydride
◦Lithium = Lithium Primary
3. Press enter to save.
Shure Incorporated
7/24
AA Battery Installation
Fully insert the batteries as shown to ensure proper battery contact and to allow the door to latch securely.
Shure SB900A Rechargeable Battery
Shure SB900A lithium-ion batteries offer a rechargeable option for powering the transmitters. Batteries quickly
charge to 50% capacity in one hour and reach full charge within three hours.
Single chargers and multiple bay chargers are available to recharge the Shure batteries.
Caution: Only charge Shure rechargeable batteries with a Shure battery charger.
Shure SB900A Runtime
2 mW 10 mW 35 mW
Up to 9 hours Up to 9 hours Up to 5 hours
Checking Battery Info
When using a Shure rechargeable battery, the receiver and transmitter home screens display the number of hours
and minutes remaining.
Detailed information for the battery is displayed Battery menu of the transmitter: Utilities > Battery
•Battery: The chemistry type of for the installed battery (Shure, Alkaline, Lithium, NiMH)
•Bars: Indicates the number of bars displayed
•Time: Battery runtime
•Charge: Percentage of charge capacity
•Health: Percentage of current battery health
•Cycle Count: Total of the number of charging cycles for the installed battery
•Temperature: Battery temperature reported in Celsius and Fahrenheit
Shure Incorporated
8/24
Important Tips for Care and Storage of Shure Rechargeable Batteries
Proper care and storage of Shure batteries results in reliable performance and ensures a long lifetime.
•Always store batteries and transmitters at room temperature
•Ideally, batteries should be charged to approximately 40% of capacity for long-term storage
•Periodically clean the battery contacts with alcohol to maintain ideal contact
•During storage, check batteries every 6 months and recharge to 40% of capacity as needed
For additional rechargeable battery information, visit www.shure.com.
AA Batteries and Transmitter Runtime
Transmitters are compatible with the following AA battery types:
•Alkaline
•Nickel Metal Hydride (NiMH)
•Lithium Primary
A 5-segment battery indicator representing the charge level of the transmitter battery is displayed on the screens
of the transmitter and receiver. The following tables contain the approximate remaining transmitter runtime in
hours:minutes.
Note: Battery runtimes vary by manufacturer, battery age, and environmental conditions.
AA Batteries and Transmitter Runtime
Alkaline
Battery Indicator
Approximate Run
time Remaining
(hours:minutes)
8:00 - 6:00
> 4:00
> 1:45
≦1:45
≦0:45
Shure Incorporated
9/24
Battery Indicator
Approximate Run
time Remaining
(hours:minutes)
≦0:15
NiMH (2700 mAh)
Battery Indicator
Approximate Runtime Remaining
(hours:minutes)
11:00 - 8:00
> 5:00
> 2:00
≦2:00
≦0:45
≦0:15
Lithium Primary (3500 mAh)
Battery Indicator
Approximate Runtime Remaining
(hours:minutes)
14:00 - 10:00
> 6:00
> 2:00
≦2:00
≦0:45
≦0:15
Menu Parameters
The Main menu organizes the available transmitter parameters into three sub-menus:
•Radio
•Audio
•Utilities
Shure Incorporated
10/24
Tip: Use the arrow buttons to scroll between the sub-menus.
Tips for Editing Menu Parameters
•To access the menu options from the home screen, press the enter button. Use the arrow buttons to access ad
ditional menus and parameters.
•A menu parameter will blink when editing is enabled
•To increase, decrease or change a parameter, use the arrow buttons
•To save a menu change, press enter
•To exit a menu without saving a change, press exit
Menu Map
Menu Parameter Descriptions
Radio Menu
Freq
Press the enter button to enable editing of a group (G:) channel (C:) or frequency (MHz). Use the arrow buttons to
adjust the values. To edit the frequency, press the enter button once to edit the first 3 digits, or twice to edit the
second 3 digits.
Power
Higher RF power settings can extend the range of the transmitter.
Note: Higher RF power settings decrease battery runtime.
Output
Other manuals for AD1
3
This manual suits for next models
1
Table of contents
Other Shure Transmitter manuals
Popular Transmitter manuals by other brands
Dejero
Dejero EnGo 3x manual
Rosemount
Rosemount 4600 Reference manual
Speaka Professional
Speaka Professional 2342740 operating instructions
trubomat
trubomat GAB 1000 instruction manual
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 instructions
Rondish
Rondish UT-11 quick start guide
