Shure Microflex MX424/N Technical manual
MX400 Series
Gooseneck Microphones
Online user guide for Shure Microflex MX400 Series miniature gooseneck-mounted electret condenser microphones.
Version: 5 (2019-J)
Shure Incorporated
3/11
•
•
•
•
•
•
•
•
MX400 Series
Gooseneck Microphones
General Description
Shure Microflex MX400S Series microphones are miniature gooseneck-mounted electret condenser microphones designed
primarily for speech and vocal pickup. They can be mounted on lecterns, pulpits, or conference tables. All models include a
preamplifier and are available with interchangeable cardioid, supercardioid, or omnidirectional cartridges.
Wide dynamic range and frequency response for accurate sound reproduction
Interchangeable cartridges that provide an optimal polar pattern choice for each application
Shock mount provides over 20 dB of isolation from surface vibration noise
Snap-fit foam windscreen
RF filtering
MX400 microphones are available with 305 mm (12 in.) or 457 mm (18 in.) goosenecks, with or without a mute switch. They
are available in supercardioid, cardioid and omnidirectional polar patterns.
"S" models include a mute button and LED.
"D" models include a desktop base with programmable mute button and LED and logic input and output.
"SE" models feature a surface mount flange with side-exit cable.
The polar pattern of the included cartridge is indicated by a model number suffix:
/C Cardioid
/S Supercardioid
/O Omnidirectional
/N Cartridge not included
Interchangeable Cartridges
®
Shure Incorporated
4/11
•
•
Microflex microphones use interchangeable cartridges that allow you to choose the polar pattern for different installations.
Snap-Fit Windscreen
Snap into the groove below the cartridge.
To remove, spread the gap with a screwdriver or thumbnail.
Shure Incorporated
5/11
•
•
•
•
•
•
Provides 30 dB of "pop" protection.
Preamp Gain
If necessary, the preamplifier gain can be reduced by 12 dB. Contact an authorized Shure service center for information.
Microphone Placement
Aim the microphone toward the desired source, such as the talker.
Aim it away from any unwanted source, such as a loudspeaker.
Place the microphone within 15 to 30cm (6 to 12 in.) of the desired sound source.
Always use the supplied windscreen or optional metal windscreen to control breath noise.
If four or more microphones will be open at the same time, use of an automatic mixer, such as the Shure SCM810 or
SCM410, is recommended.
Permanent Installation
Mount the microphone using one of the following methods.
Shure Incorporated
6/11
1.
2.
3.
4.
5.
1.
2.
3.
4.
Flange
Drill a 22 mm (7/8 in.) diameter hole in the desired location.
Trace and drill three starter holes for the supplied screws using the flange as a template.
Insert the preamplifier through the mounting flange.
Slip the mounting flange retaining ring over the bottom of the preamplifier and slide it up until it is flush to the bottom of
the flange. Then press the ring firmly into place.
Secure the flange to the mounting surface with three screws.
Shock Mount
Drill a 44mm(1-3/4 in.) diameter hole in desired mounting surface.
Mark and drill starter holes for screws, using shock mount as a template.
Secure shock mount to mounting surface with screws.
Thread the supplied adapter onto the MX400 microphone before inserting it into the shock mount.
Shure Incorporated
7/11
Specifications
Type
Electret Condenser
Frequency Response
50–17000Hz
Polar Pattern
MX412/C, MX418/C Cardioid
MX412/S, MX418/S Supercardioid
Shure Incorporated
8/11
Output Impedance
180Ω
Output Configuration
Active Balanced
Sensitivity
@ 1 kHz, open circuit voltage
Cardioid –35dBV/Pa(18 mV)
Supercardioid –34dBV/Pa(21 mV)
1 Pa=94 dB SPL
Maximum SPL
1 kHz at 1% THD, 1 kΩ load
Cardioid 124dB
Supercardioid 123dB
Self Noise
A-weighted
Cardioid 28dBSPL
Supercardioid 27dBSPL
Signal-to-Noise Ratio
Ref. 94 dB SPL at 1 kHz
Cardioid 66dB
Supercardioid 68dB
Dynamic Range
1 kΩ load, @ 1 kHz
96dB
Common Mode Rejection
10 Hz to 100 kHz
45dB, minimum
Clipping Level
at 1% THD
–6dBV (0.5V)
Polarity
Positive sound pressure on diaphragm produces positive voltage on pin 2 relative to pin 3 of output XLR
connector
Mute Switch
MX412S/MX418S
–50dB minimum
Shure Incorporated
9/11
Environmental Conditions
Operating Temperature –18–57°C (0–135°F)
Storage Temperature –29–74°C(–20–165°F)
Relative Humidity 0–95%
Power Requirements
11–52 VDC, 2.0mA
Shure Incorporated
10/11
Certifications
Meets essential requirements of all applicable European Directives.
Eligible for CE marking.
The CE Declaration of Conformity can be obtained from Shure Incorporated or any of its European representatives. For contact
information please visit www.shure.com
The CE Declaration of Conformity can be obtained from: www.shure.com/europe/compliance
Authorized European representative:
Shure Europe GmbH
Headquarters Europe, Middle East & Africa
Department: EMEA Approval
Jakob-Dieffenbacher-Str. 12
This manual suits for next models
12
Table of contents
Other Shure Microphone manuals
Shure
Shure PGA 52 User manual
Shure
Shure SM87A User manual
Shure
Shure PGA181 PG Alta series User manual
Shure
Shure KSM32 User manual
Shure
Shure PG81 Installation instructions
Shure
Shure Microflex MX395 User manual
Shure
Shure SM81 User manual
Shure
Shure Beta 53 User manual
Shure
Shure MXA920 Assembly instructions
Shure
Shure Sonobar 488A User manual
Shure
Shure SV100C User manual
Shure
Shure Microflex MX391 Series User manual
Shure
Shure Long Ranger CB41 User manual
Shure
Shure 444T User manual
Shure
Shure SM7B User manual
Shure
Shure 596LB User manual
Shure
Shure 596LB User manual
Shure
Shure Microflex MX100 Series User manual
Shure
Shure MXA710 Series User manual
Shure
Shure VP83 User manual
