Shure 33-44 Series User manual
1/5
33-44 Series -- Phono Cartridge
General Description
Shure cartridges can be used in DJ or Hi-Fi applications.
The M70BX is not recommended for heavy scratching.
Install Your Cartridge
1. Carefully remove the stylus from the cartridge. See Figure 1.
2. Use needle-nose pliers to connect the colored wires from the tonearm headshell to the corresponding pins on
the cartridge. See Table 1 and Figure 2.
Table 1. Cartridge Wiring
HEADSHELL WIRE COLOR PIN
RIGHT "HOT" RED R
RIGHT GROUND GREEN RG
LEFT "HOT" WHITE L
LEFT GROUND BLUE LG
Figure 1
Shure Incorporated
2/5
Figure 2
Figure 3
1. Attach the cartridge to the headshell using the screws supplied. See Figure 3. Tighten the screws after posi
tioning the cartridge (and headshell weight, if desired) according to one of the methods described below.
2. Carefully insert the stylus into the cartridge.
Choose a Method for Cartridge Positioning
HI-FI Setup: For maximum fidelity and minimal record wear, position the cartridge using an alignment protractor or
the overhang gauge supplied with your turntable. Level your tonearm (See Figure 7). Use Table 2 and "Setting a
Precise Tracking Force", below, to set the typical tracking force for your cartridge. Set the anti-skate control to the
same number as the tracking force.
Shure Incorporated
3/5
Figure 4
Standard DJ Setup: Mount cartridge at rear of headshell. Set tonearm height to 4-5. Set tracking force to 3
grams. Set anti-skate control to 0.
Figure 5
Unorthodox DJ Setup: Reverse the counterweight and mount it flush with the end of the tonearm. Mount car
tridge (with headshell weight) flush with the front edge of the headshell. Set anti-skate control to 0.
Figure 6
Level Your Tonearm
Figure 7
Extra Skip Resistance for DJ's:
Mount the cartridge at a 23 degree angle as shown, so that the cartridge points to the tonearm pivot. Set anti-skate
to 0.
Shure Incorporated
4/5
Setting a Precise Tracking Force
1. After mounting the cartridge on the tonearm, rotate the circular weight at the back of the tonearm until the nee
dle floats evenly above the record.
2. Hold the circular weight in place and rotate the calibration ring to read zero. The tonearm should still float even
ly above the record.
3. Rotate the weight until the calibration ring indicates the desired tracking force.
Care and Cleaning
•DJs: Don't use more tracking force than necessary to prevent skipping. Excess force will burn records, damage
needles, and reduce sound quality.
•Clean the stylus with the supplied cleaning brush.
Brush from the back to the front only, as shown in Figure 9.
Figure 9
Cartridge Specifications
Table 2. Cartridge Specifications
Shure Incorporated
5/5
Car
tridge
Replace
ment Sty
lus
Stylus
Color
Stereo Output (1 KHz
at 5 cm/sec peak
recorded velocity)
Frequency
Response in
Hz
Tracking
Force Range
(grams)
Typical
Tracking
Force
(grams)
M44-7 N44-7 White 9.5 mV 20 to 20,000 1-3 3
M44G N44G Gray 6.2 mV 20 to 20,000 .75-1.5 1.5
M35S N35S Char
treuse
5.0 mV 20 to 20,000 3-5 4
35X N35X White 6.0 mV 20 to 20,000 1.5-3 3
M70BX N70BX Beige .0 mV 20 to 18,000 1.5-3 3
SC35C SS35S Light
Blue
5.0 mV 20 to 20,000 4-5 4.5
All Cartridges and Styli
•Standard ½ inch mount for DJ turntables
•Wide diameter styli for reduced record wear
•Optimum Load:
◦47 K Ohms, M44: 400-500 pF
◦M35, M70BX, SC35C: 200-300 pF
•Inductance:
◦M44: 720 Mh, M35
◦SC35C: 425 mH
◦M70BX: 600 mH
•Channel Separation: 20 dB at 1KHz
Table of contents
Other Shure Microphone manuals
Shure
Shure SM7 User manual
Shure
Shure 450 Series II User manual
Shure
Shure PG ALTA PGA 57 User manual
Shure
Shure 575S User manual
Shure
Shure DL4 DuraPlex User manual
Shure
Shure SM7B User manual
Shure
Shure UNIDYNE III Series User manual
Shure
Shure SM89 User manual
Shure
Shure PE588 User manual
Shure
Shure Microflex MX400 Series User manual
