SensoScientific OTA Series User manual
OTA Series
User Guide
V1.02
OTA Series User Guide 1
Contents
OTA Series....................................................................................................2
Getting to Know Your Device ........................................................................2
SensoScientific Cloud ...................................................................................3
Setting Up Your Device: App.........................................................................4
Step 1 –Download App.............................................................................4
Step 2 –Set Device to Provisioning Mode ................................................5
Step 3 –Connect to Wi-Fi..........................................................................6
Step 4 –Configure Wi-Fi ...........................................................................8
Setting Up Your Device: Browser................................................................10
Step 1 –Set Device to Provisioning Mode ..............................................10
Step 2 –Connect to Wi-Fi........................................................................11
Step 3 –Configure the Node ...................................................................13
Step 4 –Verify Profile..............................................................................15
Display Notifications....................................................................................16
LED Status ..................................................................................................18
Push-Button Functions................................................................................20
Wake Up:.................................................................................................20
Silence Speaker:......................................................................................21
Min/Max Reset:........................................................................................22
Turn Off Device:.......................................................................................24
Delete Wi-Fi SSID and Password:...........................................................25
Document Information.................................................................................27
OTA Series User Guide 2
OTA Series
The OTA series is the second generation of Wi-Fi Sensors from
SensoScientific. This series of nodes boasts over-the-air upgrade (OTA)
capabilities. This enable the devices to remotely upgrade firmware without
the need to be manually serviced. The devices offer a large, 2.7” e-ink
technology display which constantly shows the most current readings on the
node. Critical functions include 2.4GHz 802.11 b/g/n Wi-Fi compatibility with
an onboard visual and audible alarm in the event of data excursions. The
battery level is shown along with several feedback notifications on the upper
panel of the display. Additional alerts can be provided through a variety of
methods such as SMS, text message, voice call, pager, cell phone, fax, and
e-mail. All data is time-stamped and recorded –holding 4000 readings locally
and transmitting data perpetually to cloud.
Getting to Know Your Device
Figure 1 –OTA Node
LED
M8 Connector
Push-Buttons
Display
OTA Series User Guide 3
SensoScientific Cloud
The SensoScientific Cloud is the platform that all data is received and
recorded. The cloud can be accessed via any internet enabled device using
the following link:
Cloud.SensoScientific.com
Use the Login Information provided to you to login.
Figure 2 –Installation Slip
Figure 3 –Cloud Monitoring
OTA Series User Guide 4
Setting Up Your Device: App
The device set-up process takes only a few short minutes. For the device to
work properly, it must to set-up to a Wi-Fi Network. If you opted for
SensoScientific to pre-configure the device, please disregard this section.
The device can be configured using the SensoScientific app available on iOS
or Android devices. If you do not have a smartphone to use, go to the browser
method (See Page 10). The following are required to proceed:
1) OTA Wi-Fi Node(s)
2) 2.4GHz Wi-Fi Source
3) Internet accessible iOS or Android cell phone
Note: iOS 8 / Android 6.0 or newer is required.
Step 1 –Download App
Go to your phone’s app store. Search and download “SensoScientific”.
Figure 4 –Search App
OTA Series User Guide 5
Step 2 –Set Device to Provisioning Mode
The OTA device must be configured to the provisioning mode. This is done
by turning the device on (put the batteries in). The device screen will flash,
and the yellow LED will turn on solid. The device will attempt to connect to a
Wi-Fi source for 15 seconds. After this time, the device will alert that no
connection was established by alternating between the green and red LED
with an audible beep.
Figure 5 –Provisioning LED Flashing
Now, press the left and right buttons simultaneously on the device to enter
the provisioning mode.
Figure 6 –Provisioning Activation
OTA Series User Guide 6
Step 3 –Connect to Wi-Fi
On your cell phone, connect to the Wi-Fi network “mysimplelink-57D475”.
This will connect your phone to the OTA Node. See below for further
instructions on how to connect your phone to a Wi-Fi network using an iOS
or Android device:
Figure 7 –Connect Phone to OTA Sensor
OTA Series User Guide 7
iOS
1. From your Home screen, go to
Settings > Wi-Fi.
2. Turn on Wi-Fi.
Your device will automatically search for
available Wi-Fi networks
3. Tap the name of the Wi-Fi network that you
want to join - “mysimplelink-57D475”.
The digits after the hyphen will be the last 6
characters of the device’s MAC Address.
Android
1. Open the settings app.
You can find this in the apps drawer.
2. Tap the Wi-Fi symbol at the top left.
3. Tap the name of the Wi-Fi network that you
want to join - “mysimplelink-57D475”
The digits after the hyphen will be the last 6
characters of the device’s MAC Address.
4. Tap Connect to join the network.
Figure 8 –iPhone Set-Up
Figure 9 –Android Set-Up
OTA Series User Guide 8
Step 4 –Configure Wi-Fi
Now that you are connected to the OTA node from your cellular phone, go to
the SensoScientific app.
Figure 10 –SensoScientific App
From the app, go to the Wi-Fi Setup link at the bottom of the main screen.
Configure to the desired network from this platform.
Figure 11 –Wi-Fi Set-Up
Select the security that the network uses and input the appropriate
information for the OTA node to join the network.
OTA Series User Guide 9
Figure 12 –Enterprise Security
Note: The platform supports enterprise security
Once all the appropriate information has been added, select “Join” at the top
right of the screen to connect the device to the desired network. If any issues
are found while trying to connect or at any time throughout the set-up process,
contact technical support. 1-800-279-3101
Support extension - option 4 at the prompt
Plug the probe into the device and place the probe wherever you are
looking to monitor data. Go to cloud.sensoscientific.com to access your
data. Use the username and password provided to you via email or in the
Installation Slip within your shipment (See Figure 2)
This manual suits for next models
1
Table of contents
Popular Temperature Controllers manuals by other brands
SMC Networks
SMC Networks Thermo-con INR-244-639 Operation manual
eltherm
eltherm Ex-TC It Series operating instructions
Omron
Omron C200H-TV Series Operation manual
industrie technik
industrie technik CA1 instructions
KRAL
KRAL EET 32 operating instructions
dixell
dixell XR420C Installing and operating instructions