Seiko H558-5009 Operating manual
SETTING INSTRUCTIONS FOR SEIKO H558-5009 MOVEMENT
This watch has three different time zones:
• Analog time.
• Digital time.
• Second digital time (local-time), displayed with "-L" in the right corner of the display.
These work independently, the alarm and hourly chime always refer to the digital time.
ANALOG TIME SETTING
• Unscrew the crown and pull it out to position 3 when the second hand is at 12 o’clock
• Turn the crown to set the desired HOUR and MINUTES.
• In accordance with the time signal or SECONDS digits “00” in the DIGITAL TIME
display, push the crown in.
• Screw the crown in to the normal position
DIGITAL (DISPLAYS) SETTING
• Push button B until the time is on the display.
• Unscrew the crown. Pull crown to position 2.
• In the TIME display, turn the crown clockwise/counterclockwise to set the HOUR
and Minutes digits
• To set SECONDS to “00”, press “B” in accordance with the second hand at 12
o’clock position.
• Each pulling out (1st click) and pushing back the crown changes 12/24-HOUR
INDICATIONS alternately.
Note: 1. When the SECONDS read any number from “30” to “59” and “B” is
pressed, one minute is added.
2. Check that “A” (AM)/”P” (PM) is set properly.
3. The digits change quickly when the crown is turned fast.
ALARM TIME SETTING
• In the ALARM display, turn the crown to set the desired HOUR and MINUTES.
Note: Check that “A” (AM)/”P” (PM) is set properly.
Switch alarm and hourly chime on/off.
With each pulling out (1st click) and pushing back the crown in the ALARM display,
the alarm and hourly time signal appear and disappear in the following sequence.
LOCAL TIME SETTING
• In the LOCAL TIME display (“L” mark appears), turn the crown to set the desired
HOUR and MINUTES.
• Each pulling out (1st click) and pushing back the crown changes 12/24-HOUR
INDICATIONS alternately.
CALENDAR SETTING
• In the CALENDAR display, turn the crown clockwise to set MONTH and DATE
• Turn the crown counter clockwise to set DAY of the week
• Only the DAY and DATE appear when the crown is at normal position
After all adjustment are completed, screw the crown in to the normal position.
STOPWATCH
• Press “B” to show the STOPWATCH display.
• The stopwatch can measure up to 60 minutes. After 60 minutes, it will star
counting again from “00:00oo”.
1. Standard measurement: To start: Press “A”
To stop: Press “A”
To reset: Hold “A”
2. Accumulated elapsed time measurement
To start: Press “A”
To stop: Press “A”
To restart: Press “A”
To stop: Press “A”
Light.
• Push button A to illuminate the digital display. Does not work in stopwatch mode.
Alarm test.
• Push buttons A and B simultaneously to sound the alarm.
Table of contents
Other Seiko Watch manuals
Seiko
Seiko 9R86 User manual
Seiko
Seiko G510 Quick start guide
Seiko
Seiko V400A Installer manual
Seiko
Seiko 7S26 User manual
Seiko
Seiko SSC642P User manual
Seiko
Seiko SSA447 User manual
Seiko
Seiko VD 57 User manual
Seiko
Seiko Pulsar Y182 User manual
Seiko
Seiko 5R66 User manual
Seiko
Seiko Credor 6870 User manual
Seiko
Seiko Pulsar 7T32 User manual
Seiko
Seiko V111 User manual
Seiko
Seiko SDWE21P1 User manual
Seiko
Seiko 6N76A Quick start guide
Seiko
Seiko 7T92 User manual
Seiko
Seiko Grand Seiko 9S65 User manual
Seiko
Seiko KINETIC 7D46 User manual
Seiko
Seiko V147 User manual
Seiko
Seiko KINETIC 5M43 User manual
Seiko
Seiko QUARTZ 9F83 User manual
