Seiko G510 Quick start guide
= Precautions
For G510 caliber watches, as they incorporate a microcapsule-type
electrophoresis display module and employ a special case structure, all repair,
adjustment, and replacement must be carried out in Japan, with the exception
of replacement of “Urethane Safety Catcher” or batteries.
Battery replacement can be done only at Seiko Service Centres where the
Water-Resistance Tester S-451A is equipped.
As soon as you receive a request from a customer, immediately contact the CS
Department.
11) Loosen and remove the four “battery cover screws” (#7500920).
* Use sufficient force as adhesive is used for preventing the screws from
loosening.
Pay attention not to damage or scratch the case and battery cover.
The other 6 screws should not be touched.
Use a short screwdriver because the case shape is unusual.
Avoid diagonally inserting a long screwdriver because this will cause
damage to the screw head.
1/4
PARTS CATALOGUE /TECHNICAL GUIDE
SEIKO EPD WATCH
Cal. G510
(for Battery Replacement)
2 Remove the “battery cover.”
Remove the “battery clamp” (#4225544) using tweezers.3
4Replace the battery (CR2025)
When setting the battery, insert it diagonally from the side so as not to
bend the terminal spring.
Set the “battery clamp” correctly.
5
6Touch the two terminals beside the battery to create a short circuit for
resetting system.
* Refer to the instructions on the rear side of the battery cover.
2/4
TECHNICAL GUIDE Cal. G510
* Confirm that the display shows <12:00>.
Apply a small amount of adhesive “LOCTITE 241” to the four screw
holes on the battery cover.
*First, remove any remaining adhesive before applying the new adhesive.
Set “gasket for the battery cover” (0G286BCA2).
8
* Be sure to use a new one.
7
* Apply grease as necessary.
Close the “battery cover.”
9
* Pay attention not to displace the “gasket.”
* You may put the “battery cover” below, and place the watch body onto
the cover.
*Dry the adhesive with the battery cover down under a temperature
of not more than 50°C.
3/4
TECHNICAL GUIDE Cal. G510
Check that the display shows the time by pressing “button A” and the
calendar by pressing “button B.”
11
Button A Button B
Ensure the non-water resistant level by use of the water-resistance
tester S-451A.
* Set the detector to the glass part in a similar manner as a normal
watch.
* In the case where water resistance cannot be determined, remove the
battery cover to reset the gasket and try again.
10
4/4
TECHNICAL GUIDE Cal. G510
Parts for G510
CASE BACK SCREW 81506329
BATTERY HATCH GASKET 0G286BCA2
URETHANE SAFETY CATCHER DFW8EB
ATTERB Y CLAMP 4225544
Table of contents
Other Seiko Watch manuals
Seiko
Seiko V072 User manual
Seiko
Seiko 9R66 User manual
Seiko
Seiko 5Y85 User manual
Seiko
Seiko 4F32A User manual
Seiko
Seiko Astron 3X22 User manual
Seiko
Seiko Presage SSA457J User manual
Seiko
Seiko Cal. 5M82 User manual
Seiko
Seiko Caliber 9S85 User manual
Seiko
Seiko 7B26 User manual
Seiko
Seiko N830 User manual
Seiko
Seiko S140A Installer manual
Seiko
Seiko 5Y63 User manual
Seiko
Seiko ANALOGUE QUARTZ SOLAR V145 User manual
Seiko
Seiko KINETIC 7L22A Installer manual
Seiko
Seiko 4M21 User manual
Seiko
Seiko 7T82 User manual
Seiko
Seiko KINETIC AUTO RELAY 5J21 User manual
Seiko
Seiko 2A22A Quick start guide
Seiko
Seiko 5T82 User manual
Seiko
Seiko ASTRON 8X22 GPS SOLAR User manual
