Seiko 7K52 User manual
English
11
DIVING MEASUREMENT
●The watch measures the current depth, maximum depth, diving time and time submerged,
and indicates them with the four hands for diving measurement and the small hands at the 6
o’clock position.
●Current depth: Indicated by DEPTH and 1/10 m hands
in 0.1 m increments from 1.6 m up to
55.0 m. (Ex. 12.5 m)
●Maximum depth: Indicated by MAX. DEPTH hand
in 0.5 m increments from 1.5 m up
to 55.0 m. (Ex. 20.5 m)
●Diving time: Indicated by DIVING TIME hand up to
12 hours.
(Ex. 17 minutes)
●Time submerged: Indicated by small hands at the 6
o’clock position. (Ex. 10:10)
HOW TO READ THE MEASUREMENTS
English
12
0.0 m
1.6 m
55.0 m
Diving measurement starts when
you descend to 1.6 m or more.
Never operate the crown while
the measurement is in progress.
HOW TO USE THE DIVING FUNCTION
Before diving, check the hands
for diving measurements.
Press button B repeatedly.
Log data
of the
last dive
Log data of
the dive
before last
Diving hands
at “0”
position
English
13
Extra measurement range warning !
Rapid ascent warning !
➡
Diving measurement stops when
you ascend to less than 1.6 m.
Case I
Case II
Case I :
If you stay at less than 1.6 m underwater
for more than 10 minutes, the dive is
considererd to be completed.
Case II :
If you descend again to 1.6 m or more
underwater before 10 minutes have
elapsed, the two dives are considered
inseparable, and the measurement is
resumed.
English
14
●Before starting a dive, be sure to check that the hands for diving measurement are reset to “0” position.
If not, reset them following the procedure in “ADJUSTING THE HAND POSITION BEFORE DIVING”.
●When you ascend to a depth less than 1.6 m underwater and the watch stops measuring the depth,
the DEPTH and 1/10 m hands indicate “0.0 m”.
●If you descend again to a depth of 1.6 m or more underwater before 10 minutes have elapsed, the time
elapsed after the depth measurement is stopped is added to the measured diving time.
●For 10 minutes after a dive, all the three buttons will not work.
●After 10 minutes have elapsed following a dive, recall of log data is made possible by pressing button
B.
Beep
Beep
Warning sound beeps intermittently for
about 10 seconds and 1/10 m hand
moves back and forth.
WARNING FUNCTION FOR DIVING
RAPID ASCENT WARNING
●The watch monitors the change of depth at 10 second intervals and gives a warning if
the diver ascends more than 3 m in 10 seconds, that is, at a rate of more than 18 m per
minute.
Other manuals for 7K52
1
Table of contents
Other Seiko Watch manuals
Seiko
Seiko Analog Quartz 7T32 User manual
Seiko
Seiko ASTRON 8X42 GPS SOLAR User manual
Seiko
Seiko W524 User manual
Seiko
Seiko Grand 3F81 User manual
Seiko
Seiko Cal. V195 User manual
Seiko
Seiko Prospex SNR035 User manual
Seiko
Seiko Y739A Quick start guide
Seiko
Seiko Map Meter / Mile Marker User manual
Seiko
Seiko 6R20 User manual
Seiko
Seiko 9R86 User manual
Seiko
Seiko 7T86 User manual
Seiko
Seiko Spectrum SVRD001 G510 User manual
Seiko
Seiko SRPH29K User manual
Seiko
Seiko 3M62A Installer manual
Seiko
Seiko 7B72 Operating manual
Seiko
Seiko Prospex S23629J User manual
Seiko
Seiko 6M15 User manual
Seiko
Seiko A257A Quick start guide
Seiko
Seiko 8R48 User manual
Seiko
Seiko KINETIC 7D48 User manual
