Sealey TPK253 User manual
TOW POLE 2500KG ROLLING LOAD CAPACITY
MODEL NO: TPK253
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
9Maintain the tow pole in good condition. If the tow pole is damaged, remove from service.
9Check vehicle manufacturer’s instructions to determine whether the vehicle is equipped with proper tow fittings suitable for use with a
tow pole. Also any special instructions for vehicles with automatic transmission or four wheel drive.
9Use tow pole only on vehicles with standard tow eyes. DO NOT use transportation ‘tie down’ points.
9Ensure the tow eyes, and the areas of the vehicles to which the eyes are fitted, are strong and solid enough for towing.
8DO NOT use the tow pole if there is damage or heavy rust around the fitting area and ensure the eyes are approximately the same
height from the ground.
9Place an “ON TOW” notice in the back window or other visible location at the rear of the towed vehicle. Attach a red marker (provided) to the
centre of the tow pole.
9The vehicle to be towed must be fully legal in respect of having the registration number visible at all times, must have a valid road tax,
insurance and relevant current DOT test certificate.
8DO NOT tow a vehicle that lacks one or more of these requirements.
9Towed vehicle must have the ignition on in order to operate lights, brake lights and indicators. If these lights cannot be operated, you must fit
a repeater trailer board to towed vehicle. Contact your Sealey stockist for information relating to approved towing boards which must
incorporate lighting and signalling equipment.
9Ensure that the person in the towed vehicle is aware that, if servo brakes and/or power steering are fitted, then braking and/or steering
efforts will be very much higher than normal when the engine is not running.
9Read vehicle manufacturers instructions before use.
8DO NOT exceed the rated capacity of the tow pole.
8DO NOT exceed a maximum towing speed of 15mph.
8DO NOT use the tow pole if damaged.
8DO NOT tow vehicle if the steering lock cannot be disengaged.
8DO NOT use the tow pole on a vehicle with defective braking system.
8DO NOT tow an unmanned vehicle.
8DO NOT force the tow pole to achieve a task it was not designed to perform.
8DO NOT allow untrained persons to use the tow pole.
8DO NOT operate the tow pole if any parts are missing as this may cause failure and possible personal injury.
2. iINTRODUCTION
2.5 tonne rolling load capacity tow pole. Hook mechanism allows for mounting pole between vehicles where towing eyes may be mixed, i.e. not
both horizontal or vertical.
3. SPECIFICATION
Model no: .................................................................. TPK253
Maximum rolling load capacity: ................................ 2.5tonne
Length:.........................................................................1.8mtr
4. TOWING INFORMATION
IMPORTANT INFORMATION REGARDING THE TOWING OF VEHICLES WITH AUTOMATIC TRANSMISSION AND FOUR WHEEL
DRIVE VEHICLES.
4.1. Before towing a four wheel drive vehicle or a vehicle with automatic transmission it is essential to consult the manufacturer’s
handbook for the vehicle to be towed to check the correct towing procedure. The correct procedure will vary from vehicle to
vehicle depending on the configuration of the transmission. (In some cases certain 4WD vehicles cannot be towed with all four
wheels on the ground and will have to be transported on a trailer). Failure to observe the correct procedure could result in severe damage
to the vehicles transmission.
4.2. Many automatic transmissions require the engine to be active in order to drive a pump that provides lubrication to the transmission. If the
transmission is turned by the road wheels without the engine running, permanent damage could be done to the transmission due to lack
of lubrication. This could also apply to the secondary gearbox on a four wheel drive vehicle.
TPK253 |Issue:3 (H,F) 12/03/18
Original Language Version
© Jack Sealey Limited
Refer to
instruction
manual
4.3. Four wheel drive systems are designed to run in tandem with the engine. If the engine is off but the transmission is driven at speed
by the road wheels the mismatch in speed between components within the gearboxes could also result in permanent damage to the
transmission.
4.4. It is usually possible to tow four wheel drive vehicles with manual transmission as the engine can be disconnected from the primary
gearbox. However, the road wheels may still be driving a secondary gearbox. The manufacturer will state in which drive position
the secondary gearbox should be placed and will recommend a maximum towing speed. A towing distance and/or time limit may also be
imposed by the manufacturer.
4.5. Some four wheel vehicles are fitted with devices to disconnect the hubs and/ or driveshafts especially for towing purposes.
4.6. Consult the manufacturer’s handbook before reversing with a four wheel drive vehicle attached or a vehicle with automatic transmission.
REMEMBER, ALWAYS FOLLOW THE VEHICLE MANUFACTURERS RECOMMENDATIONS FOR THE VEHICLE TO BE TOWED.
5. ASSEMBLY
5.1. Remove contents from packing and check to ensure everything is correct and undamaged. Should you experience any problems
contact your supplier immediately.
5.2. Position the towing vehicle so that the distance between the towing eyes is approximately 1.8 metres.
5.3. Insert shackle (A) through the towing eye on the towing vehicle. Introduce tube (B) into the shackle, align the holes in the two
components and screw the shackle bolt (C) fully into position.
5.4. Slide the central tube (D) over the end of tube (B) and align the holes in the two components. Insert the sprung pin (E) to hold the two
tubes together.
5.5. Insert tube (F) into the other end of the central tube (D). Align the holes in the two components and insert the other sprung pin (G).
5.6. If the towing eyes on the two vehicles are not in the same plane, turn tube (F) through 90º and insert the sprung pin through the
alternative holes on axis (XX).
5.7. Insert shackle (H) through the towing eye on the vehicle to be towed and if necessary carefully adjust the distance between the two
vehicles so that shackle bolt (J) can be inserted and screwed fully down.
6. TOWING PROCEDURE
6.1. TPK253 has a rolling load capacity of 2.5 tonne, based on a level surface. Remember the weight of towed vehicle should be
calculated to include any load in the vehicle, and to take into account any extreme gradients.
WARNING! Before using equipment ensure you have read, understood and apply Section 1 Safety Instructions.
TOWING EYES - Many vehicle manufacturers include a separate towing eye which is not permanently fixed to the chassis.
Important: Before fitting the tow pole, to either vehicle, check the manufacturers’ handbooks to ensure that the towing points
(do not use ‘tie points’) are suitable for use with a tow pole and are capable of safely withstanding a ‘brake load’.
LEGAL REQUIREMENTS - It is the responsibility of the towing driver to ensure that all legal requirements are met. This includes the
towing operation and actions taken by the towed driver. Check you are insured for towing. Trade users must have a “Trade Insurance
Policy” which covers commercial towing. Note the policy will not provide cover if the law is broken, or the weight of towed load
exceeds the capacity of the tow pole, or if towed vehicle weighs more than the towing vehicle. When calculating the weight of the
towed vehicle remember that any load carried in the vehicle must be added to the kerb weight indicated in the manufacturer’s
handbook.
6.2. When towing, unlock the steering wheel and activate the warning lights on both vehicles. Ensure that the towed vehicle is in neutral,
the wheels are free to rotate, and that hand and foot brakes are disengaged.
6.3. While driving, the tow pole must remain parallel with the direction of travel, i.e. if the tow fittings are placed on different sides of the
vehicles, it will be necessary to drive out of line (the car being towed would not be directly behind the one towing). Pole must also be
approximately parallel with the road surface i.e. with the towing eyes at similar heights.
6.4. The distance between the vehicles must be enough for the driver in the towed vehicle to see the rear lights of the towing vehicle.
6.5. A MAXIMUM SPEED OF 15MPH should not be exceeded.
6.6. Always take great care when towing and ensure a very gradual “take-up” when starting and braking. WARNING! The tow pole and
fittings are not able to withstand shock loads resulting from sudden changes in speed.
6.7. After use, dismantle the tow pole, clean it and store it in a dry place. Inspect regularly for signs of stress or wear. Replacement parts
are not available for this unit.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
TPK253 |Issue:3 (H,F) 12/03/18
Original Language Version
© Jack Sealey Limited
Parts support is available for this product. Please email sales@sealey.co.uk or telephone 01284 757500
Table of contents
Other Sealey Automobile Accessories manuals
Sealey
Sealey CAR3000LR User manual
Sealey
Sealey WK01 User manual
Sealey
Sealey VS721.V2 User manual
Sealey
Sealey BS3.V3 User manual
Sealey
Sealey MR360 User manual
Sealey
Sealey POWER PRODUCTS RS103 User manual
Sealey
Sealey TDRWA User manual
Sealey
Sealey WS570 User manual
Sealey
Sealey TB18LEDW User manual
Sealey
Sealey PROJ1612V User manual
Sealey
Sealey TPK2522 User manual
Sealey
Sealey BS17 User manual
Sealey
Sealey TBU01 User manual
Sealey
Sealey TPK2522.V2 User manual
Sealey
Sealey BS3.V2 User manual
Sealey
Sealey VSE725.V2 User manual
Sealey
Sealey RB951 User manual
Sealey
Sealey VSe4779.V2 User manual
Sealey
Sealey VS7010 User manual
Sealey
Sealey ARB120 User manual
