Seagate Medalist 1721 User manual
......................................
Medalist 1721 (ST31721A)
......................................
Medalist 1010 (ST31010A)
......................................
for ATA (IDE)-Compatible PCs
......................................
......................................
Installation Guide
......................................
-2 Medalist 1721, 1010, Rev. B
© 1997–1999 Seagate Technology, Inc. All rights reserved.
Publication Number: 21200092-001, Rev. B, March 1999
Seagate, Seagate Technology, and the Seagate logo are regis-
tered trademarks of Seagate Technology, Inc. Medalist, DiscWiz-
ard, SeaFAX, SeaFONE, SeaBOARD, and SeaTDD are either
trademarks or registered trademarks of Seagate Technology,
Inc. or one of its subsidiaries. All other trademarks or registered
trademarks are the property of their respective owners.
Medalist 1721, 1010, Rev. B -1
Contents
What you need........................................................................ 1
Before you begin .................................................................... 1
Handling precautions............................................................. 2
Master/slave jumpers............................................................. 3
Attaching cables and mounting the drive............................ 5
Configuring your computer................................................... 8
Addressing drive capacity limitations................................ 10
Partitioning and formatting your drive............................... 12
Installation using Disk Manager........................................ 13
Windows 95 or Windows 98 installation ........................... 14
Standard DOS installation................................................ 15
Additional installation options............................................ 17
Non-ATA compatible slave jumper...................................... 17
Cable select jumper ............................................................. 18
Advanced Disk Manager options........................................ 19
Troubleshooting ................................................................... 22
Seagate Technology support services............................... 28
Storing and shipping your drive......................................... 34
iii
0 Medalist 1721, 1010, Rev. B
iv
Medalist 1721, 1010, Rev. B 1
What you need
•Straight-edge and Phillips screwdrivers
•Four 6-32 UNC drive mounting screws
•An ATA host adapter and interface cable (max length: 18
inches) with enough connectors for all your drives
•An unused drive power cable for your new drive
•A bootable DOS system diskette (Seagate recommends using
DOS Version 5.0 or later.)
•If you are mounting this 3.5-inch drive in a 5.25-inch drive bay,
you need a mounting adapter or frame kit. Also, you may need
drive mounting rails if your drive bay is not designed for direct
mounting.
Before you begin
•Make sure your computer is turned off before you open the
case.
•Read the handling precautions following and inspect the drive
to make sure that it is not damaged.
•Save your foam-lined Seagatedisc drive box. Seagate has
approved this box for shipping a Seagate disc drive. Using any
other container or packing material voids your drive warranty.
2 Medalist 1721, 1010, Rev. B
Handling precautions
Disc drives are extremely fragile. Do not drop or jar
your drive.
Keep the drive in its antistatic bag until you are
ready to install it.
Protect your drive from static discharge by making
sure you are well grounded before touching the
drive. We recommend wearing a grounded wrist
strap throughout the installation process. Do not
touch the connectors or any part of the printed cir-
cuit board.
Always handle the drive by its edges or frame.
Do not apply pressure or attach labels to the circuit
board or the top of the drive.
Medalist 1721, 1010, Rev. B 3
Master/slave jumpers
If your new Seagatedrive will be the only drive in your computer,
you do not have to change any jumper settings. In this case, skip
ahead to “Attaching Cables and Mounting the Drive,” on page 5.
If you already have one hard drive in your computer and you are
installing a second drive, you must configure one drive as a mas-
ter and the other as a slave.
To configure the drive as a master or one drive only:
•Place a jumper on pins 5 and 6 (see Figure 1 on page 4).
The master drive usually defaults to being the “boot” drive
(drive C), from which the computer loads system software
when it first starts up.
To configure the drive as a slave:
•Remove all the jumpers.
•If you need to change the jumpers on your existing hard drive,
see the Disk Manager online manual, look on the drive label,
or contact the drive manufacturer.
4 Medalist 1721, 1010, Rev. B
Figure 1. Master and slave jumper settings
pin 1
ATA interface
connector
135
246
Slave
Master or single drive
4-pin power
connector
Medalist 1721, 1010, Rev. B 5
Attaching cables and mounting the drive
1. If you are attaching a new ATA interface cable to a single
drive, attach one end of the cable to the interface connector
on your host adapter or motherboard. Motherboard connec-
tors can be identified by the IDE or HDD 40-pin connector.
The ATA cable must be no more than 18 inches (457 mm)
long.
2. Thread the interface cable through the drive bay and attach
the connector at the end of the interface cable to your new
drive.
Note. If you have two drives, attach the second drive to the sec-
ond connector.
Figure 2. Attaching the cables
Caution. To avoid possible damage to your system,
make sure to align pin 1 on the host adapter or mother-
board with pin 1 on your drive or drives. Pin 1 on the
interface cable is usually indicated by a stripe along the
edge of the cable.
Pin 1
Host
adapter
!
6 Medalist 1721, 1010, Rev. B
Figure 3. Mounting screws
3. You can mount the drive in any orientation. Usually it is
mounted with the circuit board down.
4. Slide the drive carefully into the drive bay. Secure the drive
with four 6-32 UNC mounting screws in either the side-
mounting holes or the bottom-mounting holes. Insert the
screws no more than 0.22 inch (5.58 mm) into the bottom-
mounting holes and no more than 0.20 inch (5.0 mm) into the
side-mounting holes.
Caution. To avoid possible damage to the drive, do not
overtighten the screws or use metric screws.
!
This manual suits for next models
1
Table of contents
Other Seagate Storage manuals
Seagate
Seagate ST9250317AS - Momentus 5400 FDE 250 GB Hard... User manual
Seagate
Seagate 15K.5 - Cheetah - Hard Drive User manual
Seagate
Seagate EE25.2 - Series 80 GB Hard Drive User manual
Seagate
Seagate ST650211CF User manual
Seagate
Seagate MOMENTUS 42.2 ST9100822A User manual
Seagate
Seagate Barracuda 7200.7 ST3160021AS User manual
Seagate
Seagate SkyHawk AI User manual
Seagate
Seagate Enterprise Value ST3000NC002 User manual
Seagate
Seagate STM3250620A - Maxtor DiamondMax 250 GB Hard... User manual
Seagate
Seagate ST3146855LC - Cheetah 146.8 GB Hard Drive User manual
Seagate
Seagate ST320410ACE User manual
Seagate
Seagate ST2400MM0129 User manual
Seagate
Seagate BlackArmor NAS 110 User manual
Seagate
Seagate ST31000525SV - 1.0TB 7200RPM Sata... Operating and safety instructions
Seagate
Seagate ST3250310CS User manual
Seagate
Seagate ST4000VM000 User manual
Seagate
Seagate Backup Plus Desktop User manual
Seagate
Seagate Replica User manual
Seagate
Seagate Barracuda ATA III Family User manual
Seagate
Seagate GoFlex Satellite User manual
