Scott 47604 User manual

IMPORTANT! For secure mounting, follow instructions thoroughly.

47604 Scott®Electronic Counter Mount

Foam Skin Care Dispenser

Soap Discharge Head

Support Shaft

Support Ring

Motor Module

Soap Rell Bottle (order separately)

Battery Compartment Base

Battery Compartment Cover

Split Support Ring (Optional)

A B

Below indicates how the system ts together when installed.

033955 • 9/2019

2 3

INSTALLATION INSTRUCTIONS

Materials Required:

• Power Driver

• Phillips Bit

• Phillips Screwdriver

• Cutting Fluid

• 1” Diameter Hole Saw (Diamond Bit for

Granite or Stone)

• Clear Silicone Caulk

• Safety Glasses

• Magic Marker

Note: If drilling of the countertop is

required, be sure to use an approved

Kimberly-Clark Professional Installer

or other trained professional.

If a 1” hole already exists on the

countertop, go to Step F.

If drilling a new hole, it is recommended

the hole be away from the faucet,

preferably in the 10 o’clock or 2 o’clock

position (Figure 1).

Use the plastic template provided to

determine the appropriate position

from the sink’s edge, based on what is

under the countertop, the hole should

be drilled. Note the maximum dimension

from the center of the hole to the edge

of the sink is 3.5 inches (Figure 2).

Once the location is determined, trace

the 1” diameter hole using a marker

(Figure 3).

Drill a 1” diameter hole in the marked

location (Figure 4). Clean the area

around the hole so it is free of debris.

IMPORTANT – Use the proper drill bit

for your surface and use cutting uid to

cool the bit during drilling.

Select the appropriate head discharge

location ensuring soap will discharge

into the sink (Figure 5).

Break away the center portion of the

plastic template and discard the piece

removed (Figure 6).

Parts included in the package for installation of the dispenser:

Optional part:

Above Counter Chrome Spacer – this part is used to allow the soap discharge head to be raised

up, moving the sensor out of the range of hand washing, which can cause inadvertent dispensing.

10:00 2:00

Optional Head

Discharge Location

Preferred Head

Discharge Location

3.5”

I K

A. Support Shaft

B. Soap Discharge Head

C. Motor Module

D. Battery Compartment

(Base, Cover, and Batteries

4 D cell)

E. Plastic Template

F. Screws and Anchors

G. Allen Wrench

H. Split Support Ring

I. Support Ring

J. Key

K. Hand Tool

L. Breakaway Screws

Position template over hole in counter

positioning discharge head so soap

will discharge into sink. Peel adhesive

backing off above counter spacer, align

with opening in template and press

down rmly to secure to countertop

(Figure 7).

Insert the support shaft through the hole

in the above counter spacer aligning the

support shaft with the spacer (Figure 8).

Remove template and discard.

Remove the adhesive liner from the

plastic support ring and from the

underside of the countertop, slide it thru

the support shaft and push it up until it

sticks to the underside of the countertop

(Figure 9).

Note: If the support ring will not sit ush

with the underside of the countertop

due to interference with the sink, use

the optional split support ring provided

instead.

IMPORTANT – USING A PHILLIPS

BIT IN A POWER DRIVER, TIGHTEN

AT FULL SPEED THE 2 SCREWS

ON THE SUPPORT SHAFT UNTIL

THE PLASTIC HEADS BREAK AWAY.

REMOVE THE REMAINS OF THE

WHITE PLASTIC HEADS FROM THE

SUPPORT SHAFT (Figure 10).

Use the hand tool provided to complete

the tightening of the support shaft. Tighten

in a clockwise direction (Figure 11).

Push the signal cable attached to the

soap discharge head thru the opening in

the support shaft (Figure 12).

Align the notches on the bottom of the

soap discharge head with the tabs on the

support shaft (Figure 13).

Rotate the soap discharge head counter-

clockwise until the tab on the soap

discharge head is aligned with the rear

tab on the support shaft (Figure 14).

Important – Using the Allen wrench

provided, tighten the set screw clockwise

on the back of the soap discharge head

until it is tight. The head of the set screw

should be ush with the surface of the

soap discharge head. (Figure 15).

IMPORTANT – APPLY A BEAD OF

CLEAN SILICONE CAULK AROUND

THE PERIMETER OF THE SOAP

DISCHARGE HEAD OR THE ABOVE

COUNTER SPACE, IF USED (Figure 16).

6 7

Position the clear tube on the signal

cable into the notch on the bottom of the

support shaft (Figure 17).

Remove the protective cap on the signal

cable plug. Align the yellow arrow on the

signal cable plug with the yellow arrow on

the motor module receptacle (Fgure 18).

Push the signal cable plug into the motor

module receptacle. The connection is

secured when the yellow arrow on the

signal cable plug is no longer visible

(Figure 19).

Align the orange arrow on the motor

module with the orange arrow on the

support shaft. Push the motor module

up until BOTH snaps lock into place

(Figure 20).

Install the battery compartment to the back

or side wall under the countertop using the

included screws or double sided tape (not

included). Refer to gure 21. Position the

battery compartment no further than 32”

from the motor module. Route the power

cable 10” above the oor in a position so

that it will not interfere with changing rells

(Figure 22).

Push the battery compartment cover onto

the battery compartment base until both

the top and bottom of the cover snap into

place (Figure 23).

Note: The batteries are already loaded in the

battery compartment cover..

WInstall the power cable plug into the

power receptacle on the motor module

(Figure 24).

Note: To change batteries, push the key

fully into the top of the assembled battery

compartment (Figure 25) then grip the battery

compartment cover and pull it away from the

battery compartment base (Figure 26). Load

new batteries and then repeat Step 23. Use

only Alkaline D-Cell (LR20) Excell, Procell,

Energizer Max, Duracell Coppertop, or Gold

Peak replacement batteries.

10” minimum height from oor

Recommended to avoid interference with

cleaning equipment.

FLOOR

32” Maximum distance

Route cable to

avoid interference

while relling.

Secure cable to

wall as required.

Fig. 24

SOAP REFILL BOTTLE INSTALLATION

AND REMOVAL INSTRUCTIONS

USER GUIDE FOR THE SCOTT®ELECTRONIC COUNTER MOUNT

FOAM SKIN CARE DISPENSER

LED INDICATORS:

There are several indicator LED’s on the soap

discharge head which are used as follows:

Yellow LED (Low Product) – The yellow LED will

begin to ash slowly (1 time every second) when

the soap rell has between 50 and 90 shots of

soap remaining.

Red LED (Low Battery) slow ash – The red

LED will begin to ash slowly (1 time every

second) when battery power remaining is

sufcient for approximately 500 additional shots

of soap.

Red LED (Low Battery) rapid ash – The red LED will begin to ash rapidly (4 times every

second) when battery power is not sufcient to activate the dispenser. Replace batteries.

Red LED (Motor Short) – The red LED will begin to ash 2 times every second. Reboot the

dispenser by disconnecting and reconnecting the power.

Note:

• When power is supplied to the system prior to installing a soap rell, the red and yellow LED

will ash, indicating a good power connection has been established. It will continue to ash

until a soap rell is installed.

• When a soap rell is properly loaded into the dispenser the red and yellow LED will stop

ashing indicating the rell is properly installed.

Yellow LED

Red LED

Slip the straw into the underside of the

motor module (Figure 1).

Push the rell bottle ush to the motor

module until both snaps are secure

(Figure 2).

Note: When power is supplied to the

system prior to installing a soap rell, the

red and yellow LEDs will ash indicating

a good power connection has been

established. The LEDs will continue to

ash until a soap rell is installed.

When a soap rell is properly loaded

into the dispenser the red and yellow

LEDs will stop ashing indicating the

rell is properly installed.

Prime the pump by placing one hand

under the soap discharge head to

activate the motor. Repeat 4 to 5 times

until a consistent shot of foam soap is

discharged (Figure 3).

To remove an empty rell bottle,

squeeze the release tabs 1 on the top

of the rell and slide the bottle down 2

and out (Figure 4).

Snap 1 Snap 2

10 11

Problem Cause Correction

Support shaft does not t

into countertop.

Hole in countertop too

small.

Drill out hole to 1" minimum

diameter.

Support shaft still loose

after tightening.

Plastic screw head broke

prematurely.

Use tool provided to manually

tighten the support fasteners.

Signal cable plug from

soap discharge head

does not t into receptacle

on motor module.

Protective cap on signal

cable plug not removed.

Plug not properly aligned.

Remove protective cap.

Align the yellow arrows.

Motor module does

not snap into the

support shaft.

Cable not positioned

properly.

Motor module not properly

aligned.

Obstruction under the

countertop.

Push the cable into the support

clip at the bottom of the support

shaft.

Align the orange arrows of

the support shaft to the motor

module.

Relocate obstruction.

Red and yellow LED does

not ash when power is

connected.

Batteries not installed

properly.

Power cable plug not fully

seated in receptacle.

Check orientation of batteries in

battery compartment.

Insure power cable plug is fully

seated.

Red and yellow LED

continues to ash when

soap rell is installed.

Rell not properly installed. Remove the rell and re-insert

insuring both snaps fully

engage.

Soap does not dispense

when activated.

Pump not primed.

Rell discharge tube

damaged.

Batteries not properly

installed.

Rell is empty.

Motor short.

Activate unit for 4 to 5 times to

prime the pump.

Check rell discharge tube for

cuts or kinks. Replace rell if

needed.

Check battery alignment.

Replace empty rell with a full

one.

Reboot the dispenser by

disconnecting and reconnecting

the power.

Troubleshooting Guide

Problem Cause Correction

Inadvertent soap

dispensing.

Sensor range too long. Move sensor switch to low.

Soap shot is all liquid

instead of foam.

Rell is defective. Replace rell.

Existing hole in counter

not 1”.

Call your representative for

direction.

Soap does not dispense

when activated.

(continued)

Batteries can no longer

activate the dispenser

(Red LED ashing

4 times per second).

Signal cable from

discharge head damaged.

Water contamination on

motor module.

Replace batteries.

Replace discharge head.

Replace motor module. Insure

discharge head is properly

secured tightly to countertop.

Insure to seal the support shaft

to the countertop with silicone

caulk.

Yellow LED ashing on

soap discharge head.

Low soap level. Soap will run out in 30 to

90 shots, replacement is

recommended.

Red LED ashing slowly (1

time per second).

Low battery level. Battery power will run out in

approximately 500 shots.

Red LED ashing rapidly

(4 times per second).

Batteries can no longer

activate the dispenser.

Replace batteries.

Soap shot is all liquid

instead of foam.

Rell is defective. Replace rell.

Red LED ashing

(2 times per second).

Motor short. Reboot the dispenser by

disconnecting and reconnecting

the power.

Existing hole in counter

not 1”.

Call your representative for

direction.

12 13

Troubleshooting Guide (continued)

Problem Cause Correction

Soap does not

dispense when

activated. (continued)

Batteries can no longer

activate the dispenser

(Red LED ashing

4 times per second).

Signal cable from discharge

head damaged.

Water contamination on

motor module.

Replace batteries.

Replace discharge head.

Replace motor module. Insure

discharge head is properly

secured tightly to countertop.

Insure to seal the support shaft to

the countertop with silicone caulk.

Yellow LED ashing on

soap discharge head.

Low soap level. Soap will run out in 30 to

90 shots, replacement is

recommended.

Red LED ashing

slowly (1 time per

second).

Low battery level. Battery power will run out in

approximately 500 shots.

Red LED ashing

rapidly (4 times per

second).

Batteries can no longer

activate the dispenser.

Replace batteries.

Soap shot is all liquid

instead of foam.

Rell is defective. Replace rell.

Red LED ashing

(2 times per second).

Motor short. Reboot the dispenser by

disconnecting and reconnecting

the power.

Existing hole in

counter not 1”.

Call your representative for

direction.

Americans with Disabilities Act (For use in U.S. only): Title III of the Americans with Disabilities Act

(“ADA”) governs, in detail, the placement and operation of dispensers. You should ensure that your

mounting and use of dispensers complies with that law as well as the regulations issued under that

statute. The mounting suggestions in this document may or may not fulfill the obligations of the ADA

with respect to your facility.

Ley de protección de discapacitados (aplicable sólo en EE.UU.). El Artículo III de la Ley de

protección de discapacitados, ADA (

Americans with Disabilities Act

) regula en detalle la instalación

y el funcionamiento de distribuidoras. Asegúrese que la instalación y las disposiciones de uso de la

distribuidora cumplan con esta ley y los reglamentos correspondientes derivados de ella. Es posible

que las instrucciones de instalación aquí descritas cumplan o no con las disposiciones de la ADA

dependiendo de las características de su construcción.

Loi concernant les Américains handicapés : Le titre III de l’

Americans with Disabilities Act

(«

ADA ») (Loi concernant les Américains handicapés) régit, de façon détaillée, l’emplacement et le

fonctionnement des boîtes distributrices. Vous devez veiller à ce que votre méthode de pose et

d’utilisation des boîtes distributrices soit conforme à la loi, de même qu’aux règlements y afférents.

Les suggestions relatives à la pose qui figurent dans le présent document peuvent répondre ou non

aux exigences de l’ADA dépendant du type d’installation.

KIMBERLY-CLARK CORPORATION DISCLAIMS LIABILITY FOR PERSONAL INJURIES OR

PROPERTY DAMAGES RESULTING FROM INSTALLATION NOT PERFORMED BY KIMBERLY-

CLARK.

KIMBERLY-CLARK CORPORATION RECHAZA TODA RESPONSABILIDAD POR LESIONES

PERSONALES O DAÑOS Y PERJUICIOS DEBIDOS A INSTALACIONES NO REALIZADAS POR

KIMBERLY-CLARK.

KIMBERLY-CLARK CORPORATION DÉCLINE TOUTE RESPONSABILITÉ POUR LES BLESSURES

PERSONNELLES OU LES DOMMAGES À LA PROPRIÉTÉ RÉSULTANT D’UNE INSTALLATION

N’AYANT PAS ÉTÉ EFFECTUÉE PAR KIMBERLY-CLARK.

KIMBERLY-CLARK CORPORATION HAFTET NICHT FÜR DURCH EINE INSTALLATION

ENTSTANDENE PERSONEN- BZW. SACHSCHÄDEN, WENN DIESE VON ANDEREN ALS VON

KIMBERLY-CLARK DURCHGEFÜHRT WURDE.

KIMBERLY-CLARK CORPORATION AANVAARDT GEEN AANSPRAKELIJKHEID VOOR

LICHAMELIJK LETSEL OF MATERIËLE SCHADE DIE VOORTVLOEIT UIT EEN NIET DOOR

KIMBERLY-CLARK UITGEVOERDE INSTALLATIE.

KIMBERLY-CLARK CORPORATION ESCLUDE LA PROPRIA RESPONSABILITÀ PER DANNI ALLA

PERSONA O A PROPRIETÀ DERIVANTI DA OPERAZIONI DI INSTALLAZIONE NON EFFETTUATE

DA KIMBERLY-CLARK.

КОМПАНИЯ KIMBERLY-CLARK CORPORATION СНИМАЕТ С СЕБЯ ОТВЕТСТВЕННОСТЬ ЗА

ТЕЛЕСНЫЕ ПОВРЕЖДЕНИЯ ИЛИ УЩЕРБ ИМУЩЕСТВУ, ЯВЛЯЮЩИЕСЯ РЕЗУЛЬТАТОМ

УСТАНОВКИ, ВЫПОЛНЕННОЙ НЕ КОМПАНИЕЙ KIMBERLY-CLARK.

A KIMBERLY-CLARK CORPORATION DECLINA QUALQUER RESPONSABILIDADE POR LESÕES

PESSOAIS OU DANOS MATERIAIS RESULTANTES DE INSTALAÇÃO NÃO EFECTUADA PELA

KIMBERLY-CLARK.

®/* Trademarks of Kimberly-Clark Worldwide, Inc. / Marques déposées de Kimberly-Clark Worldwide, Inc.

Table of contents

Other Scott Dispenser manuals

Scott

Scott PURELL ONVATION CXR Manual

Popular Dispenser manuals by other brands

Silver King

Silver King Majestic SK12MAJ Technical manual and replacement parts list

Franke

Franke F3Dn Twin Service manual

STIEBEL ELTRON

STIEBEL ELTRON UltraHot Plus Operation and installation instructions

DAN DRYER

DAN DRYER 282 installation guide

Essity

Essity Tork 473208 manual

CBS

CBS SD300BU-88 COMPONENT MAINTENANCE MANUAL WITH ILLUSTRATED PARTS LIST

Sealey

Sealey MK77 manual

Fluid Management

Fluid Management Accutinter 1600 End user guide

Franke

Franke DVS SD99-010 Installation and operating instructions

Graco

Graco Dispensit 1053-10C operation & maintenance

ITALTINTO

ITALTINTO i50 user manual

Coca-Cola

Coca-Cola FREESTYLE 9000 user guide

Graco

Graco ProMix 2KE Operation

TECHCON SYSTEMS

TECHCON SYSTEMS TS1251 user manual

Wayne

Wayne GLOBAL VISTA CNG instruction manual

clarsen

clarsen H133 Instructions for use

PicoBrew

PicoBrew Zymatic user manual

BOWMAN

BOWMAN BP-007 manual