SciCan Statim 2000 Installation guide

Statim 2000 & 5000

Rev. 7 PCB

Field

Training Manual

Statim Rev. 7 PCB User Setup

User setup mode – To initially setup your Statim

Hold down the Stop button and turn the unit ON.

Unit ID Setup *

Water Quality

Last Printout *

RS232 *

End Of Line CR/LF *

Serial Port Bit rate *

Printer user º char *

Save and Exit

Exit

* Only used when Statim is connected to a Printer or Data Logger

Keypad:

Unwrapped Select next item in the menu

Wrapped Select previous item in the menu

Rubber and Plastics Enter the indicated sub menu selection

Stop Exit menu to normal mode of operation

Time/Date Setup Mode – Set the proper time and date

Keypad:

Unwrapped Increase current field (the flashing value on the display)

Wrapped Decrease current field (the flashing value on the display)

Rubber and Plastics Select next field

Stop Save & exit menu to normal mode of operation

18:00 07/09/2008

HH:MM MM/DD/YYYY

>Time/Date Setup

Language Setup

Language Setup – Display information in your desired language

Available Languages

N. A. English (North American English)

U. K. English (United Kingdom English)

Francais (French)

Deutsch (German)

Espanol (Spanish)

Italiano (Italian)

Dansk (Danish)

Portugues

Nederlands

Japanese

Svenska (Swedish)

Polski (Polish)

Magyar (Hungarian)

Cesky (Czech)

Norsk (Norwegian)

Islenska (Iceland)

Slovencina (Slovak)

Eesti (Estonian)

Japanese (Sterimaster)

Romana (Romanian)

Lietuviuk (Lithuanian)

Slovenian (Slovenia)

Keypad:

Unwrapped Select next language

Wrapped Select previous language

Rubber and Plastics If Repeater mode is ON, this key will scroll through all the available

display messages of the chosen language.

Stop Save & exit menu to normal mode of operation

Unit ID Setup – Associate unit with an ID number (Used with printer)

Keypad:

Unwrapped Decrease current field (the flashing value on the display)

Wrapped Increase current field (the flashing value on the display)

Rubber and Plastics Select next digit

Stop Save & exit menu to normal mode of operation

Unit # :

000

N. A. ENGLISH

Water Quality – Display detected water quality

Screen Representation

x.x Water conductivity in uS (micro-Siemens)

NNN Water conductivity in ADC (Analog to Digital converter) counts (0…255)

y.y Water quality in ppm (parts per million)

Keypad:

Rubber and Plastics Return to main menu

Stop Exit menu to normal mode of operation

Last Printout – Printer reprints last cycle and unit returns to normal mode of operation

(Used with printer)

RS232 – To select which serial device to attach (Used with printer)

Serial Printer

USB FLASH/MSD

Keypad:

Unwrapped Move to next option, second line shows the new value

Wrapped Move to previous option, second line shows the new value

Rubber and Plastics Save and return to main menu

Stop Exit menu to normal mode of operation without saving

>RS232

N/A

>Water Quality

CD= x.xuS/NNN/y.yppm

End of Line CR/LF – Configure the printout layout (Used with printer)

This only needs to be set if a serial printer is attached to the serial port.

Available options:

- No line terminator is sent after each line. To be used with printer that accepts only 20

characters per line and automatically advances to next line. Should be used with the

STATprinter.

CR A <CR> is sent at the end of the line. To be used with printers that advance to

beginning of next line when a CR is received.

CR/LF A <CR><LF> is sent at the end of the line. To be used with printers that translate

advance to beginning of next line only when LF is received.

Keypad:

Unwrapped Select next option. Second line shows the new value

Wrapped Select previous option. Second line shows the new value

Rubber and Plastics Save & exit to main menu

Stop Exit and return to normal mode of operation

SciCan Suggested

External Printers End Of Line

CR/LF Serial Port Bit Rate Printer user °char

Epson

TM-U220D C31C515603) CR/LF 9600 248 [0xF8]

Citizen

IDP-3110-40 RF 120B CR 9600 N/A

Star Micro

SP212FD42-120 CR 9600 210 [0xd2]

Star Micro

SP216FD41-120 CR/LF 9600 210 [0xd2]

Star Micro

SP512MD42-R CR/LF 9600 210 [0xd2]

>End Of Line CR/LF

CR/LF

Serial Port Bit Rate – Choose bit rate for device connected to the serial port (Used with printer)

19200

57600

115200

300

1200

2400

4800

If USB FLASH/MSD is selected as the RS232 device, a Serial Port Bit Rate selection of 9600 will be

required for the Data Logger to be operational.

Keypad:

Unwrapped Select next value

Wrapped Select previous value

Rubber and Plastics Save & Return to main menu

Stop Exit without saving and return to normal mode of operation

Printer user °char – Setting to print a °C sign (Used with printer)

32 decimal value for selected char-default 32

20 hex value for the selected char-default 20

Keypad:

Unwrapped Increase value by one

Wrapped Increase value by ten

Rubber and Plastics Select and return to main menu

Stop Exit without saving and return to normal mode of operation

Save and Exit – Saving settings and return to normal mode of operation

Upon selection, current settings are saved and unit restarts in normal mode of operation

Exit – Exit menu without saving settings

Upon selection, current settings are discarded, not saved and unit restarts in normal mode of operation

Serial Port Bit Rate

9600

Printer user °char

[

0x20

]

Statim Rev. 7 PCB Service Setup

Service setup mode – To enter the Service Setup Mode, turn power switch ON while holding

down Unwrapped and Wrapped buttons.

The Service Setup Mode is password protected, a password must be entered to continue. The default

password is, Unwrapped, Wrapped, Rubber and Plastics, Stop buttons pressed in this order. If the

password has been changed the backdoor password is, Unwrapped, Wrapped, Unwrapped, Wrapped

buttons pressed in this order.

Language Setup

Unit ID Setup *

Set cycle counter

Conductivity Setup

Water Cnd Tmp. Comp

Last Printout *

Stored CF Printouts *

Clear CF Printouts *

Display last CF#

Devices Test On/Off

Temperature Offset

Validation Offset

Voltage Calibration

Voltage setup

Repeater mode

RS232 *

End of Line CR/LF *

Serial Port Bitrate *

Printer user º char *

Factory default

Change Password

Backup NVRAM

Restore NVRAM

Save and Exit

Exit

Water Pump Type

Production Cycle

* Only used when Statim is connected to a Printer or Data Logger

Keypad:

Unwrapped Select next item in the menu

Wrapped Select previous item in the menu

Rubber and Plastics Enter the indicated sub menu selection

Stop Exit menu to normal mode of operation

Calibration – Select calibration to run validation thermocouple calibration cycle only.

Note: See page 19 for validation thermocouple calibration procedure.

>Calibration

Time/Date Setup

Time/Date Setup Mode – Set the proper time and date

Keypad:

Unwrapped Increase current field (the flashing value on the display)

Wrapped Decrease current field (the flashing value on the display)

Rubber and Plastics Select next field

Stop Save & exit menu to normal mode of operation

Language Setup – Display information in your desired language

Available Languages

N. A. English (North American English)

U. K. English (United Kingdom English)

Francais (French)

Deutsch (German)

Espanol (Spanish)

Italiano (Italian)

Dansk (Danish)

Portugues

Nederlands

Japanese

Svenska (Swedish)

Polski (Polish)

Magyar (Hungarian)

Cesky (Czech)

Norsk (Norwegian)

Islenska (Iceland)

Slovencina (Slovak)

Eesti (Estonian)

Japanese (Sterimaster)

Romana (Romanian)

Lietuviuk (Lithuanian)

Slovenian (Slovenia)

Keypad:

Unwrapped Select next language

Wrapped Select previous language

Rubber and Plastics If Repeater mode is ON, this key will scroll through all the available

display messages of the chosen language.

Stop Save & exit menu to normal mode of operation

18:00 07/09/2008

HH:MM MM/DD/YYYY

N. A. ENGLISH

Unit ID Setup – Associate unit with an ID number (Used with printer)

Keypad:

Unwrapped Decrease current field (the flashing value on the display)

Wrapped Increase current field (the flashing value on the display)

Rubber and Plastics Select next digit

Stop Save & exit menu to normal mode of operation

Set cycle counter – Adjust the recorded number of cycles ran

Keypad:

Unwrapped Decrease current digit

Wrapped Increase current digit

Rubber and Plastics Select next digit

Stop Save & exit menu to normal mode of operation

Conductivity Setup – To display detected water quality

If Statim has a Float Switch and Water Quality Sensor display below will appear.

Screen Representation

x.x Water conductivity in uS (micro-Siemens)

NNN Water conductivity in ADC (Analog to Digital converter) counts (0…255)

y.y Water quality in ppm (parts per million)

LL.L Lower value threshold (No water threshold) default 0.3uS

Values lower than this trigger “No water refill reservoir” error

FLOAT Indicates the reservoir has both a Float Switch & Water Quality Sensor

HH.H High value threshold (Bad water threshold) default 10uS

Values larger than this trigger “Bad water quality” error

G.GG Water conductivity circuit gain default 1.00

Note: Distilled water readings should be between Low and High thresholds.

Go to Water Conductivity Circuit Calibration to adjust readings.

Keypad:

Unwrapped Increase current field

Wrapped Decrease current field

Rubber and Plastics Move to next field

Stop Exit menu to normal mode of operation

Note: To perform Water Conductivity Circuit Calibration see page 18.

Unit # :

000

CD= x.xuS/NNN/y.yppm

L=LL.L H=HH.H G=G.GG

Cycle Number

000000

CD= x.xuS/NNN/y.yppm

FLOAT H=HH.H G=G.GG

Water Cnd Tmp Comp - To enable or disable water conductivity temperature compensation

Off

Keypad:

Unwrapped Select next option Second line shows the new value

Wrapped Select previous option. Second line shows the new value

Rubber and Plastics Select and return to main menu

Stop Exit, without saving, to normal mode of operation

Last Printout – Printer reprints last cycle and unit returns to normal mode of operation

(Used with printer)

Stored CF Printouts – Printer prints saved cycle fault printouts and unit returns to normal mode of

operation.

The saved CF printouts are sent to the printer or data logger only when either one is attached and

configured. The following types of errors are saved:

CF’s

Water quality or Water level low errors

Cycle interrupted due to errors (##)

Clear CF Printouts – Reset Cycle Fault printout list (Used with printer)

Yes

Keypad:

Unwrapped Select next option Second line shows the new value

Wrapped Select previous option. Second line shows the new value

Rubber and Plastics Select and return to main menu

Stop Exit, without saving, to normal mode of operation

Display last CF# - Show the last Cycle Fault that occurred

Screen Representation

## Value of last recorded CF

(######) Cycle counter for last CF

Keypad:

Rubber and Plastics Return to main menu

Stop Exit to normal mode of operation

>Water Cnd Tmp Comp

>Clear CF Printouts

>Display last CF#

## (######)

Other manuals for Statim 2000

This manual suits for next models

Table of contents

Other SciCan Laboratory Equipment manuals

SciCan

SciCan statim 5000 G4 Guide

SciCan

SciCan STATCLAVE G4 User manual

SciCan

SciCan STATIM 7000 Installation guide

SciCan

SciCan HYDRIM L110w G4 User manual

SciCan

SciCan SALUS User manual

SciCan

SciCan Bravo User manual

SciCan

SciCan Statim 2000 Installation guide

SciCan

SciCan STATIM 5000S User manual

SciCan

SciCan Statim 2000 User manual

SciCan

SciCan Quantim 16 User manual

SciCan

SciCan Bravo User manual

SciCan

SciCan Hydrim L11w User manual

SciCan

SciCan BRAVO 17 User manual

SciCan

SciCan STATCLAVE G4 User manual

SciCan

SciCan Statim 2000 User manual

SciCan

SciCan HYDRIM L110w User manual

SciCan

SciCan QUANTIM B User manual

SciCan

SciCan HYDRIM C61w G4 User manual

SciCan

SciCan HYDRIM C61w G4 User manual

SciCan

SciCan statim 2000 G4 User manual

SciCan

SciCan Statim 2000 User manual

SciCan

SciCan STATIM 900J User manual

SciCan

SciCan statim 5000 G4 User manual

SciCan

SciCan STATIM 7000 User manual

Popular Laboratory Equipment manuals by other brands

Qiagen

Qiagen DML 3000 user manual

Queensgate

Queensgate NANOSCAN OP400 Quick start instructions

Conviron

Conviron GEN1000-GE Operator's manual

Parr Instrument

Parr Instrument 4560 Operating instructions manual

IKA

IKA IC control operating instructions

Integra

Integra DOSE IT operating instructions

Agilent Technologies

Agilent Technologies 5800 ICP-OES user guide

Endress+Hauser

Endress+Hauser Cleanfit CPA875 operating instructions

NI PXI-5422 CALIBRATION PROCEDURE

Collomix

Collomix Aqix operating instructions

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series operating manual

Ocean Insight

Ocean Insight FLAME-NIR+ Installation and operation manual

Parker

Parker ALIGN-MG-NA Installation, operation and maintenance manual

BD 644787 user guide

DENTAURUM

DENTAURUM Compact Megaplus Instructions for use

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 instruction manual

VWR

VWR SAS Super IAQ instruction manual

illumina

illumina MiSeqDx reference guide