Schlage S-480 User manual

How to Install

(Door thickness 40-50mm)

1. Please read the installation manual before you install the product.

2. The strike guider is served to install correctly, remove the strike guider

after installation.

3. Please check door thickness and door handing before installation.

This product can be installed with door thickness 40-50mm

Firstly, check the door opens and closes smoothly.

Fold 90° angle on the fold line of the installation template and stick it to the

door and mark for installation.

Drill holes as specified on template.

Where replacing existing mechanical auxiliary lock, use center hole on the

mounting plate to adjust position and install the product.

Fasten the front using screw (M5x30, 2pcs), to fix the mounting plate (as

required check the direction of the mounting plate). Use screw (FH1x 30, 5pcs)

to increase the strength of the mounting plate fixing.

Pull through Front cable and connect to Back connector, and then fix to the

mounting plate by using screw (M5x29, 4pcs).

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

Fix the strike with screw (FH1x 30, 6pcs) and ensure the deadbolt aligns

correctly with strike.

Insert batteries (check polarity).

Check the door opens and closes properly.

Read the user’s manual to register PIN code.

*For Metal Doors: Please use the T4x19 screws instead of FH1x 30

(Timber Doors).

(Use on indoor side)

Installation Template S-480

Please check measurements

when printing template

83mm

58mm

FH1x 30 (5pcs)

FH1x 30 (3pcs)

Screw

How to Install

(Door thickness 40-50mm)

1. Please read the installation manual before you install the product.

2. The strike guider is served to install correctly, remove the strike guider

after installation.

3. Please check door thickness and door handing before installation.

This product can be installed with door thickness 40-50mm

Firstly, check the door opens and closes smoothly.

Fold 90° angle on the fold line of the installation template and stick it to the

door and mark for installation.

Drill holes as specified on template.

Where replacing existing mechanical auxiliary lock, use center hole on the

mounting plate to adjust position and install the product.

Fasten the front using screw (M5x30, 2pcs), to fix the mounting plate (as

required check the direction of the mounting plate). Use screw (FH1x 30, 5pcs)

to increase the strength of the mounting plate fixing.

Pull through Front cable and connect to Back connector, and then fix to the

mounting plate by using screw (M5x29, 4pcs).

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

Fix the strike with screw (FH1x 30, 6pcs) and ensure the deadbolt aligns

correctly with strike.

Insert batteries (check polarity).

Check the door opens and closes properly.

Read the user’s manual to register PIN code.

*For Metal Doors: Please use the T4x19 screws instead of FH1x 30

(Timber Doors).

(Use on indoor side)

Installation Template S-480

Please check measurements

when printing template

83mm

58mm

FH1x 30 (5pcs)

FH1x 30 (3pcs)

Screw

Other manuals for S-480

1

Table of contents

Other Schlage Lock manuals

Popular Lock manuals by other brands

Magic

Magic 105 manual

Gantner

Gantner GAT NET.Lock 7020 System Installation, configuration & operation

Wittkopp

Wittkopp Insys 7202 manual

Dorma

Dorma Studio Classic Installation instruction

Securam

Securam ECSL-601 quick start guide

Sudhaus

Sudhaus 3003 operating manual

Safety 1st

Safety 1st 48517 user guide

Pado

Pado FDS-10 user manual

Esco

Esco systeQ Series installation instructions

COMPX

COMPX National D8951 instruction sheet

secureo

secureo Key Box instruction manual

Stock Loks

Stock Loks C8713 instruction sheet

COMPX

COMPX 1T-058 Information

Auslock

Auslock T11 user manual

ELCOM

ELCOM 7205 Operating instruction

Stealth SAFES

Stealth SAFES ShadowVault Instructions & Troubleshooting

Knox

Knox KeySecure 5 Admin & user guide

Kwikset

Kwikset 48334/01 Quick installation guide