Sauder Palladia 411864 User manual
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-23
Français pg 24-27
Español pg 28-31
Lot # 357575 11/25/13
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Panel TV Stand
Palladia Collection | 411864
Smart stand
for the idiot box.
Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
WARNING
!
Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or
death. A TV that is too large for the available space might be accidentally pushed or bumped o the furniture, or subject to tip-over.
• Check the size and weight of your TV. Compare it to the diagram below – before you begin assembly!
• This Sauder unit is designed for use with televisions weighing less than 95 pounds. Never use with a TV that weighs more.
• The size of the television, front-to-back and side-to-side, must fit within the space defined in the diagram.
• Never place the front edge of the TV past the front edge of the TV support shelf (or stop molding – if equipped)
• Never allow the sides of the TV to extend past the side edges of the TV support surface.
• If the TV has a CRT picture tube, the picture tube cone may extend past the rear of the support shelf.
• Be sure to apply the warning label as instructed in the last assembly step. The label provides important safety related information.
3
4
5-23
24-27
28-31
32-34
35
Tip Shown Actual Size
95 lbs.
95 lbs.
18-7/8"
18-7/8"
47"
47"
411864 www.sauder.com/servicesPage 2
Tape Measure
Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C RIGHT UPRIGHT (1)
D LEFT UPRIGHT (1)
E TOP (1)
F BOTTOM (1)
G BACK (1)
H DOOR (2)
I LARGE ADJUSTABLE SHELF (2)
J SMALL ADJUSTABLE SHELF (2)
K BASE (1)
L LOWER PLINTH (2)
M SIDE MOLDING (2)
N BOTTOM MOLDING (1)
O UPPER PLINTH (2)
P FRONT MOLDING (1)
Q RIGHT MOLDING (1)
R LEFT MOLDING (1)
S RIGHT END MOLDING (1)
T LEFT END MOLDING (1)
U RIGHT HINGE MOLDING (1)
V LEFT HINGE MOLDING (1)
W VALANCE (1)
X BRACE (1)
Y HALF DISK (2)
411864www.sauder.com/services Page 3
A
B
C
D
E
F
G
H
H
I
I
J
K
M
M
N
P
Q
R
S
T
U
V
W
X
L
L
Y
Y
O
O
J
Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
411864 www.sauder.com/servicesPage 4
FELT DISC CARD - 1
II
TIE PLATE - 4
DD
METAL BRACKET - 14
CC
GOLD 1" MACHINE SCREW - 2
PP
BLACK 9/16" LARGE HEAD SCREW - 28
RR
BLACK 1-1/4" FLAT HEAD SCREW - 18
NN
BROWN 7/16" LARGE HEAD SCREW - 8
SS
BLACK 1-7/8" FLAT HEAD SCREW - 6
MM
ZTWIST-LOCK®FASTENER - 8
OO BROWN 1" FLAT HEAD SCREW - 10
RUBBER SLEEVE - 16
KK
METAL PIN - 20
JJ
SILVER 5/8" FLAT HEAD SCREW - 8
QQ
MOLDING
CONNECTOR - 2
GG
FF
HINGE SPACER - 4
EE HINGE - 4 KNOB - 2
HH
NAIL - 36
TT
HIDDEN CAM - 4
AA2 CAM DOWEL - 4
BB2
(Refer to the last step for proper location and application)
WARNING LABEL - 1
LL
WARNING
Never use this furniture with a TV that is too
large or too heavy. Severe injury or death
can occur.The TV and furniture will be
unstable and may tip.
-The TV must less than 95 lbs.
-The base of the TV must be able to sit
completely on this shelf.
-Refer to instruction book for complete
safety information.
Note: This is a permanent label. Do not try
to remove. Surface will be damaged.
02/ 02 269227
Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å To begin assembly, push a SAUDER TWIST-LOCK®
FASTENER (Z) into the large holes in the ENDS (A and B).
Repeat this step for the BOTTOM (F)
411864www.sauder.com/services Page 5
(8 used)
Do not tighten the TWIST-LOCK® FASTENERS in this step.
Z
A
B
å Push four HIDDEN CAMS (AA2) into the
HINGE MOLDINGS (U and V).
Step 2
411864 www.sauder.com/servicesPage 6
Do not tighten the HIDDEN CAMS in this step.
Arrow
AA2
U
V
(4 used)
Hole
Arrow
å Tap two MOLDING CONNECTORS (GG) into the notches
in the MOLDINGS (P, Q, and R).
Step 3
411864www.sauder.com/services Page 7
Use your hammer to tap the MOLDING CONNECTOR (GG) into the notches in the MOLDINGS
Flat end
Flat end
PQ
R
GG GG
å Fasten the MOLDINGS (P, Q, and R) to the TOP (E). Use
eight BLACK 1-1/4" FLAT HEAD SCREWS (NN).
Step 4
411864 www.sauder.com/servicesPage 8
E
P
Q
R
BLACK 1-1/4" FLAT HEAD SCREW
(8 used in this step)
NN
Rounded edge
Surface
with holes
å Fasten the LEFT END (B) to the LEFT MOLDING (R) on
the TOP (E). Tighten two TWIST-LOCK® FASTENERS.
å Insert four METAL PINS (JJ) into the TOP (E).
å Push the UPRIGHTS (C and D) onto the METAL PINS (JJ)
in the TOP (E).
Step 5
411864www.sauder.com/services Page 9
How to use the SAUDER TWIST-LOCK®FASTENER
1. Insert the dowel end of the FASTENER into the
hole of the adjoining part.
NOTE: The dowel end of the FASTENER must
remain fully inserted in the hole of the adjoining
part while locking the FASTENER.
2. Tighten the FASTENER with a Phillips
screwdriver as tight as possible.
Dowel end
6-3/4"
7-5/8"
Finished edge
B
C
D
E
R
JJ
JJ
Surface with
6 holes
Surface with
12 holes
Surface with TWIST-LOCK®
FASTENERS
Rounded edge
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
Step 6
å Fasten the BOTTOM (F) to the LEFT END (B). Tighten two
TWIST-LOCK® FASTENERS.
å Fasten the BOTTOM (F) to the UPRIGHTS (C and D). Use
four BLACK 1-7/8" FLAT HEAD SCREWS (MM).
å Fasten the RIGHT END (A) to the BOTTOM (F) and RIGHT
MOLDING (Q). Tighten four TWIST-LOCK® FASTENERS.
411864 www.sauder.com/servicesPage 10
Unfinished
surface
Surface without TWIST-LOCK®
FASTENERS
Q
A
B
C
D
F
These holes must be here.
BLACK 1-7/8" FLAT HEAD SCREW
(4 used in this step)
MM
Other Sauder Rack & Stand manuals
Sauder
Sauder 423088 User manual
Sauder
Sauder New Prairie 08 User manual
Sauder
Sauder Harvey Park 421982 User manual
Sauder
Sauder Rustic Country 412373 User manual
Sauder
Sauder Studio 408559 User manual
Sauder
Sauder 413045 User manual
Sauder
Sauder Entertainment Credenza User manual
Sauder
Sauder Studio Edge 412067 User manual
Popular Rack & Stand manuals by other brands
Salamander
Salamander Acadia AC/W/L400/WH Assembly instructions
Fohhn
Fohhn VAT-09 Mounting instruction
ricoo
ricoo FS0522 quick start guide
AMSOIL
AMSOIL BMK-22 Installation and service instructions
Kargo Master
Kargo Master 48220 installation guide
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 installation instructions
