SATO TXPEX6 User manual
Quick Start Guide
TXPEX6
TXPEX6
Read this Quick Start manual before beginning.
For the best prinng results, we recommend the use of SATO genuine labels
and ribbons.
Contact your SATO authorized reseller for further details.
More informaon can be found at www.satoamerica.com
Important Informaon
This quick start guide provides important informaon on how to setup your
new SATO product. Be sure to read this quick start guide thoroughly before
using this printer. It is an integral part of the product and should be kept in
the immediate vicinity of the device and available to the operang sta.
Limitaon of Liability
The manufacturer will not be held liable for damage resulng from:
• Disregarding these instrucons
• Unintended use of the printer
• Unauthorized technical modicaons
• Use of unapproved consumables
i
ii
TXPEX6
Table of Contents
Table of Contents
iii
1 Unpacking the Printer 1
2 Inial Setup 2
3 Loading Ribbon 5
4 Loading Media 6
5 Connecng Cables and the Power Cord 8
6 Turning the Printer ON/OFF 9
TXPEX6
1Unpacking the Printer
1. Open the carton.
2. Remove the accessories.
a. Power cord
b. Tear-o Blade
3. Remove the foam inserts and printer.
Note: Keep the carton and packaging materials for future transportaon of
the printer.
Unpacking the Printer
1
TXPEX6
2Inial Setup
1. Open the top cover.
2. Remove the twist e securing the print head block.
3. From the accessories; locate the tear-o blade.
4. Aach the tear-o blade to the printer with the provided pan screws.
Slide the blade tabs into the notches and securely aach with the pan
screws.
5. Move the head lever to free posion.
Inial Setup
2
TXPEX6
6. Swing open the guide bracket.
7. Li the print head block.
8. Remove the bubble wrap.
Note: Keep the twist e and bubble wrap for future transportaon of the
printer.
9. Close the print head block (do not lock the guide bracket and head
lever).
10. Gently push the media sensor (green bar) all the way inward toward
the interior printer wall.
11. Li the print head block completely up and then back down.
This acon will set the default media sensor posion for SATO notched tags.
3
Inial Setup
TXPEX6
Note: The media sensor may need to be reposioned for other media
types. (Gap sensor is round and Black Mark sensor is square).
12. Loosen the thumb screw and remove the media supply Hub
assembly.
13. Loosen the Label Holder thumb screw.
14. Slide the label holder all the way inside toward the interior printer
wall and ghten the thumb screw.
This is the default posion for SATO notched tags.
Black Mark Gap
4
Inial Setup
TXPEX6
3Loading Ribbon
1. Grasp the tabs on the top and boom of the Ribbon Stoppers and
move the Ribbon Stoppers back to the end of the Ribbon Sha (inside
of the printer).
2. Li open the print head block.
3. Leaving slack between the ribbon spools, place the ribbon onto the
ribbon shas as shown below:
4. Lower the print head block and remove any slack in the ribbon.
5. Secure guide bracket and head lever to lock posion.
Note: All Ribbon must be wound coated side out (CSO)/Ink outside.
The ribbon roung guide is located on the inside of the Top Cover
Loading Ribbon
5
Table of contents
Other SATO Label Maker manuals
SATO
SATO Argox OS Series User manual
SATO
SATO TG3 Series User manual
SATO
SATO SG112-ex User manual
SATO
SATO CLLM Basic 412e User manual
SATO
SATO CL4NX RIDF Owner's manual
SATO
SATO LT408 User manual
SATO
SATO CG408 DT/TT User manual
SATO
SATO s84ex User manual
SATO
SATO TG3 Series User manual
SATO
SATO M10e Series User manual
SATO
SATO LM400e Series User manual
SATO
SATO GY412 User manual
SATO
SATO Argox LK-200 Series User manual
SATO
SATO CL4NX RIDF Instruction sheet
SATO
SATO s84ex User manual
SATO
SATO CG408 DT/TT User manual
SATO
SATO RWG500 User manual
SATO
SATO KENDO 22.6 User manual
SATO
SATO CL4NX RIDF User manual
SATO
SATO TH2 Series User manual
