Sartorius 2405 User guide

Digital Micro Balances

2405

Instructions for installation and operation

1. UNPACKING

2. INSTALLATION OF THE BALANCE

2.1. Checking the voltage setting

2.2. Detaching the transport arrestment

2.3. Assembling the balance

2.4. Inserting the glass plates

2.5. Leveling the balance

3. DESCRIPTION OF THE OPERATING KNOBS

4. CHECKING AND ADJUSTING

4.1. Focusing the projection scale

4.2. Zero point

4.3. Sensitivity

5. WEIGHING PROCEDURES

6. SUPPLEMENT

6.1. Accuracy of the built-in set of weights

6.2. Correction of the weighing result

6.3. Determination of the air density

6.4. Conditions for installing micro balances

7. TECHNICAL DATA

1. Unpacking

1.1. Carefully remove the balance from their cartons.

1.2. Carefully unpack accessories.

2. INSTALLATION

2.0.1. IMPORTANT: see supplement 6.1. to 6.4.

2.0.2. Remove outer and inner lid.

2.1. Checking the voltage setting:

2.1.1. Place balance on the rear on to the plastic dust cover. Push the cover plate in the base plate aside

and change connecting wires, if necessary. Close the cover plate and set up the balance. Remove the

adhesive tape carefully and wipe off the arrears with alcohol.

2.2. Detaching the transport arrestment:

2.2.1. Weight application must indicate “29.99”.

2.2.2. Take off cover of the damping pot.

2.2.3. 3 Loosen knurled nuts, remove paper strips, swing aside springs and retighten nuts.

Remove cardboard strip.

2.2.4. Take out balance beam. Take off 3 plastic discs (1). Loosen 3 knurled nuts (2), swing aside springs

and retighten nuts.

2.2.5. Remove cardboard strip.

Connect balance to the mains. Press gray push button (see 3.1.).

2.2.6. Remove brackets at the ends of the locking bars of the weight application.

2.2.7. Pull out bars carefully.

2.3. Assembling the balance:

2.3.1. Check arrestment pins (1), damping (2) and bearing (3) and clean, if necessary.

2.3.2. Check knife-edges and bearing and clean, if necessary.

2.3.3. Set balance beam on to the arrestment pins (1). The knife-edge must not come into contact with the

bearing.

2.3.4. Place cover plate on to the damping pot and turn anti-clockwise until the slit the cover plate runs paral-

lel with the balance beam. Turn clamp clockwise until it locks.

2.3.5. Check stirrup plate and clean, if necessary. Set stirrup plate on to the arrestment pins.

2.3.6.2. Unscrew 2 knurled nuts and take off bow.

2.3.7. Attach stirrup and insert it.

2.3.8. Unscrew 2 knurled nuts and take down carefully the locking plate for the weights. Put back the perfo-

rated plate afterwards.

2.3.9. Attach lamp housing and plug in the cable.

2.3.10. Place the inside hood on to the balance.

2.3.11. Swing out pan lifting device. Open upper sliding door and attach pan bow.

2.4. Inserting the glass plates:

2.4.1. Place glass plate into the balance and close upper sliding door. Put the balance pan on to the holder

and swing in the pan.

2.4.2. Place glass plate into the balance and close sliding door.

2.4.3. Put locking screws for the front plate into position.

2.4.4. Fasten front plate.

2.4.5.Turn weight application to “0.00” and set micrometer to “00”.

Table of contents

Other Sartorius Scale manuals

Sartorius

Sartorius combics 1 User manual

Sartorius

Sartorius Micro M 500 P User manual

Sartorius

Sartorius Secura series User guide

Sartorius

Sartorius PMA.Quality PMA7501 User manual

Sartorius

Sartorius M-Power AZ214 User manual

Sartorius

Sartorius WM Series User manual

Sartorius

Sartorius PMA.Vision User manual

Sartorius

Sartorius CUBIS MSU User manual

Sartorius

Sartorius CP324S User manual

Sartorius

Sartorius Cubis MCA Series User manual

Sartorius

Sartorius Cubis MCE32202P User manual

Sartorius

Sartorius MW1P User manual

Sartorius

Sartorius M3P User manual

Sartorius

Sartorius PMA.Quality PMA7501H User manual

Sartorius

Sartorius PMA.Evolution User manual

Sartorius

Sartorius Entris II BCA Advanced Series User manual

Sartorius

Sartorius BP 301S User manual

Sartorius

Sartorius BL150S User manual

Sartorius

Sartorius SIWABBP User manual

Sartorius

Sartorius Entris II Advanced Line BCA623-1S User manual

Sartorius

Sartorius CW3P User manual

Sartorius

Sartorius ED224S-0CE User manual

Sartorius

Sartorius ISBBS User manual

Sartorius

Sartorius Combics CAPS..-LU Series User manual

Popular Scale manuals by other brands

AWS

AWS ZEO-50 user manual

Gima

Gima Glass Body Fat Analyzer Use and maintenance book

Seca

Seca 374 user manual

TEC

TEC TEC SL59 SERIES owner's manual

Axis

Axis B/E Series user manual

Alecto

Alecto ACW-40 user manual

Rice Lake

Rice Lake MSI-4260 IS Technical manual

IKA

IKA RCT basic safety control operating instructions

ADE

ADE M20011 operating manual

Duronic

Duronic KS3000 manual

Digi

Digi SM-720 Service manual

Cardinal

Cardinal CS Series Operation manual

Korona

Korona Kastella Instructions for use

A&D

A&D FC-50Ki instruction manual

BDA

BDA CAMARGUE installation guide

Tanita

Tanita HD-357 Instructions for use

Leifheit

Leifheit 03173 quick start guide

Lumme

Lumme LU-1340 user manual