Sanus Systems BF16 User manual

Assembly Instructions for Basic Foundations: BF16, BF24, BF31

Thank you for choosing Sanus Systems Basic Foundations. Please check carefully to make sure there are no missing or defective parts.

Never use defective parts. Improper assembly may cause damage or serious injury. If you have any questions regarding this product,

contact Sanus at 800.359.5520 or visit www.sanus.com. Our customer service representatives can quickly assist you with missing or

damaged parts. Replacement parts for Sanus products purchased through authorized dealers can be shipped directly to you. Please call

Sanus Systems before returning products to the point of purchase.

Required Tools: Phillips Screw Driver.

Step 1: Check carefully to make sure all parts and hardware are accounted for.

Diagram 1: Parts and Hardware

(8) Isolation Pads - a (16) Screws - b (8) Carpet Spikes - c

(2) Base - d (2) Top Plate - e

For BF16 & BF24: (2) Wire cover - g

(4) Pillar - f For BF31: (4) Wire Cover - g

Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 1.20.05

Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com

Step 2: Assemble Pillars to Base

Using the Screws (b), allign the countersunk holes in the Base

(d) with the corresponding holes in each Pillar (f). The rounded

or beveled edge of the Pillars should face the front of the stand

as shown in Diagram 2. Proceed to tighten all 4 screws by hand

with a phillips screw driver.

Note: Do NOT use any power drivers to tighten the Screws!

Step 3: Add Top Plate to Pillars

Allign the Top Plate (e) with the Pillars (f) so that the two coun-

tersunk holes that are closer together are toward the front of the

stand. Proceed to attach the Top Plate to the Pillars by threading

a Screw (b) through each of the countersunk holes and into the

Pillar as shown in the Detailed View Diagram 3. Tighten the

Screws with a phillips screw driver.

Note: Do NOT use any power drivers to tighten the Screws!

Step 4: Add Isolation Pads and Carpet Spikes

The Isolation Pads (a) are self adhesive. For the best stabil-

ity, place them in the extreme corners of each Top Plate (e) as

shown in Detailed View A of Diagram 4.

Carpet Spikes (c) are provided to stabilize the stand on carpet-

ing and to reduce resonance. Simply insert the end of the Carpet

Spike into each small hole in the bottom side of the Base (d).

You may need to tap them in with a wooden or rubber mallet.

See Detailed View B Diagram 5 for assistance.

Note: The end of the Carpet Spikes may be sharp enough

to dimple or dent wood ﬂoors or furniture. All small objects

can be hazardous to children. The use of Carpet Spikes is

optional. Sanus Systems is not liable for damage or injury.

Step 5: Add Wire Covers

Set the speaker on the stand and run the speaker wire between

the Pillars and through the hole in the base. Snap the plastic

Wire Covers (g) into the Grooves in the Pillars. See the Top

View Diagram 5 for assistance.

Note: Each BF31 stand requires two Wire Covers to span

the full height of the stand.

Diagram 2 Detailed View

Diagram 3 Detailed View

Detailed View A

Diagram 4

a e

Detailed View B

c d

Diagram 5 Top View

wire management

hole

Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 1.20.05

Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com

This manual suits for next models

Table of contents

Other Sanus Systems Rack & Stand manuals

Sanus Systems

Sanus Systems VMCC1 Installation guide

Sanus Systems

Sanus Systems Wall Mount LL22 User manual

Sanus Systems

Sanus Systems HTSAT User manual

Sanus Systems

Sanus Systems VM2 User manual

Sanus Systems

Sanus Systems Motorized Mount LA112 User manual

Sanus Systems

Sanus Systems VMPL50 User manual

Sanus Systems

Sanus Systems VMCT User manual

Sanus Systems

Sanus Systems WMS5 User manual

Sanus Systems

Sanus Systems Sanus VisionMount VMAA18 User manual

Sanus Systems

Sanus Systems PFV60-B1 User manual

Sanus Systems

Sanus Systems VisionMount VMPL2 User manual

Sanus Systems

Sanus Systems PFV59S Installation guide

Sanus Systems

Sanus Systems WMS3 User manual

Sanus Systems

Sanus Systems VisionMount MF203 User manual

Sanus Systems

Sanus Systems SD115 User manual

Sanus Systems

Sanus Systems WMS3 User manual

Sanus Systems

Sanus Systems WMS3 User manual

Sanus Systems

Sanus Systems VMSA User manual

Sanus Systems

Sanus Systems PFV36SB-01 Installation guide

Sanus Systems

Sanus Systems New VisionMount VMA201 User manual

Sanus Systems

Sanus Systems VMCM1 User manual

Sanus Systems

Sanus Systems Sanus VisionMount LC1A User manual

Sanus Systems

Sanus Systems VM2 User manual

Sanus Systems

Sanus Systems VisionMount VM200 User manual

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 