Sangean DPR-35 User manual
DPR-35
GB
Version 1
1
IMPORTANT SAFETY INSTRUCTIONS
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
ampliers) that produce heat.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided
plug does not t into your outlet. Consult an electrician for
replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
Only use attachments/accessories specified by the
manufacturer.
Use only with the cart, stand, tripod, bracket, or table
specied by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid
injury from tip-over.
Unplug this apparatus during lightning storms or when
unused for long periods of time.
2
GB
14.
15.
16.
17.
18.
19.
20.
21.
Refer all servicing to qualied service personnel. Servicing
is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged. liquid
has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
To Reduce the Risk of Fire or Electric Shock, Do not
Expose This Appliance To Rain or Moisture.
The Shock Hazard Marking and Associated Graphical
Symbol is provided on the rear of unit.
Apparatus shall not be exposed to dripping or splashing and
no objects lled with liquids, shall be placed on the apparatus.
Excessive sound pressure on ear- and headphones could
impair the hearing ability. Higher setting that idle on the
equalizer leads to higher signal voltages on the output for
ear and headphones.
The power plug should be close to the radio, and easy to
be approached that during the emergency, to disconnect
the power from the radio, just unplug the power plug from
the AC power slot.
Where the MAINS plug or an appliance coupler is used
as the disconnect device, the disconnected device shall
remain readily operable.
To prevent possible hearing damage, do not listen
at high volume levels for long periods.
CAUTION: These servicing instructions are for use by
qualied service personnel only. To reduce the risk of the
electric shock, do not perform any servicing other than
that contained in the operating instructions unless you are
qualied to so.
3
4
GB
Controls
1Headphone socket
Lock switch (Note: If this is activated, your radio will not
operate.)
Telescopic antenna
Power button
Volume button
LCD display
Loudspeaker
Tuning/ Menu jog wheel
DC socket
2
3
4
5
6
7
8
9
5
Charging the radio
The DPR 35 features a built in 1850 mAH Lithium
rechargeable battery to power the radio.
Before operating the radio for the rst time please fully charge
the battery.
The DPR 35 is supplied with a 5V/500 mA AC adaptor.
1. Insert the adaptor plug into the DC socket on the right side
of your radio. Plug the adaptor into a standard mains outlet
and the radio will begin charging the built in battery.
Charging time is approx. 4 hours with radio off and 10 hours with
radio on. The battery power icon on the LCD display will flash
whilst charging and stop ashing when the radio is fully charged.
The battery operating time is approx. 20 hours listening through
the speaker and approx 28 hours with headphones. Reduced
power, distortion, ‘stuttering’ sounds or battery power indicator in
“low” are all signs that the battery needs to be recharged.
Note:
If charging the radio when the power is off, the battery power
icon does not display on the LCD.
Headphones
The 3.5 mm stereo headphone socket located on the top of your
radio is provided for use with stereo headphones or an earpiece.
Connecting headphones automatically mutes the built in speaker.
Important:
Excessive volume levels from earphones and headphones
may cause damage to your hearing.
6
GB
Setting the clock
The DPR-35’s clock will automatically update each time you
turn on the radio and tune to a DAB+ radio station or to an FM
station which is broadcasting the time via RDS. Time display
will ash 0:00 for a few seconds then display the clock time
when it receives DAB+ or FM – RDS clock time signal.
Initial operation – DAB+ (Digital Radio)
This step is only necessary for initial setup –
1. Ensure the battery is fully charged.
2. Fully extend the telescopic antenna.
3. Press the Power button on the left hand side of your radio.
4. The display will show “Welcome to Digital Radio” and start
to scan the entire DAB+ channel range and stop at the rst
found station. If the radio has been used before, the last
used station will be selected. Press in the tuning/menu jog
wheel to play the station.
5. Turn the jog wheel either up or down to display station list
and find desired station. Press in the jog wheel to select
the station. The radio will tune to the station and display
the station name.
6. Adjust the volume for comfortable listening.
7
Service Information – DAB+
The Service Information display - Technical information on the
current status of the station being broadcast.
While listening to DAB+, continually press in the jog wheel to
cycle through information on
a. Program type (PTY)
b. Multiplex Name
c. Time
d. Date
e. Channel and Frequency
f . Bit Rate and Codec
g. Signal Strength
Menu Functions
Press in and hold the jog wheel for 2 seconds to enter
the menu list. The display will first show DAB and <Find
Services>. Turn the jog wheel up or down and choose from
the following options: ‘Find Services’, ‘Back’, ‘FM mode’,
‘Settings’ and ‘Favorites’.
A) Find Services –
Press in the tuning/menu jog wheel and turn up or down to
select.
● Scan
press in the jog wheel to scan the whole DAB+ network in
your area. Radio will tune to the rst station found after the
scanning is completed.
8
GB
● Back
press in the jog wheel to go back to the previous menu
display.
● Manual Tune
press in and turn the jog wheel to scroll the whole station list.
Press in the jog wheel to select desired station.
B) Back
Press in the jog wheel to go back to current listening status.
C) FM mode
Press in the jog wheel to select FM band.
D) Settings
Press in the jog wheel to select from following settings
options:
● Auto select
Press in and turn the jog wheel to select YES or NO. Default
setting is NO.
Press YES and the radio will auto select and tune to the
station shown on the display within a few seconds.
● Back
Press in the jog wheel to go back to settings menu.
● Software upgrade
From time to time, new software features for your radio may
be developed. Your radio has therefore been designed to
allow its internal software to be updated using your USB
upgrade port.
9
You should not attempt to update your radio unless it is
recommended to you by Sangean Customer Services.
Updating the software may remove all network settings and
radio station presets from your radio.
Software updates for your radio may be available in the
future.
As software updates become available software and
information on how to update
your radio can be found at:
http://sg.sangean.com.tw/rst/rst.asp
http://www.sangean.eu/
www.sangean.com.au
For more information, please contact our Head Office by
sending an email to: info@ sangean.com
● SW version
Press in the jog wheel to view software version installed in the
radio. Press in the jog wheel again to go back to
Settings menu.
● Factory reset
Press in and turn the jog wheel to select YES or NO. Select
YES to erase all saved settings, station lists and favorites. All
settings will revert to factory default.
● Language
Your radio functions can be congured to a different language.
Press in and turn the jog wheel to select your desired language.
The current language setting is marked with an asterisk.
Table of contents
Other Sangean Radio manuals
Sangean
Sangean WFR-20 User manual
Sangean
Sangean dpr-202bt User manual
Sangean
Sangean PT-633 User manual
Sangean
Sangean PR-D3 User manual
Sangean
Sangean HDT-1X User manual
Sangean
Sangean WR-2CL User manual
Sangean
Sangean U4 DBT+ User manual
Sangean
Sangean DT-210 User manual
Sangean
Sangean ProTravel PT-50 User manual
Sangean
Sangean WFR-1 - DATASHEET 3 User manual
Sangean
Sangean HDR-1 User manual
Sangean
Sangean HDR-1 User manual
Sangean
Sangean DPR-99 Plus User manual
Sangean
Sangean PR-D1 User manual
Sangean
Sangean WR-2CL User manual
Sangean
Sangean HDT-1 User manual
Sangean
Sangean WFR-1 - DATASHEET 3 User manual
Sangean
Sangean WR-2 User manual
Sangean
Sangean WR-2 User manual
Sangean
Sangean WFT-1Di User manual
