Samsung SWT90C1 User manual

1 2

BEFORE USING THE WASHER

CAUTIONS

PRECAUTIONS WHEN OPERATING

DESCRIPTION OF PARTS

● Remove the cap-hose from the drain

hose. ● In case of pump drained washer,

remove the cap-hose from

the drain hole.

●Be sure that the washer is grounded.

To avoid electrical shock,use

a metal pipe for the ground

connection. But, don't ground

the washer with gas pipes or

telephone lines to avoid to

dangers of explosion or lightning strike.

●Do not put your hands into the spin

dryer basket when it is spinning.

Your fingers can be caught

by spinning laundry and

damaged.

●Ventilation opening must not be obstructed

by carpeting when the washing machine is

installed on a carpeted floor.

●If the supply cord of this appliance is damaged,

it must only be replaced by a repair shop

appointed by the manufacturer,because

special purpose tools are required.

●To avoid overfilling and damages this appliance

must be filled with the operator present using a

moderate water supply pressure only.

●This appliance is to be connected to the water

mains using new hose-sets and that

old hose-sets should not be reused.

●Never allow children to operate

or play with the washer.

Children playing with the washer

may accidentally fall into the

washing tub.

●Be sure to cover with the inner

cover on laundry before spinning.

This prevents laundry from

being tossed out and damaged.

●Before washing,check all pockets.

If nails or pins remain in pockets,they may

damage the washer or clothes.

●Close the water tap a little if the

water pressure is too high.

●To avoid water splashes,

close the wash tub lid.

●Never splash water on the control panel.

●Disconnect the power cord from the

power supply when not in use.

●Don't use excessively hot water.

(50˚C or more)

Plastic parts may be deformed or damaged.

Also, clothing may be deformed or decolored.

INNER LID

DRAIN HOSE

(with pump)

When you open this lid while

the spin basket is spinning,

the spinning will be stopped

by breake system.

POWER CORD

EARTH WIRE

(Option)

WATER DRAIN HOSE

(WITHOUT PUMP)

SPIN DRYER BASKET

SPIN DRYER HATCH

WASH TUB LID

Be sure to keep the lid

closed during washing

and spinning.

CONTROL LEG

Adjust the control leg

for even placement.

Otherwise,excessive vibration

and noise can occur

during spinning

OVER FLOW

FILTER

LINT FILTER

This is used for gathering

the dregs which are made

during washing.

WASH TUB

PULSATOR

The plug’s shape

may not correspond

with this drawing.

SPIN DRYER LID

3 4

1 2 3 4 5

4.CYCLE SELECTOR

This is used to set the Washing/Rinsing or Draining.

5. SPIN DRY TIMER

This is used to set the spin time 1-5 minutes.

1.WASH TIMER

This is used to set the wash time, 1-15 minutes.

2.WASH CONTROL

You can wash laundry effectively by various methods.

3.SPIN DRY TIMER

This is used to set the spin time 1-5 minutes.

4.WATER INTAKE

Connect water inlet to a tap with a suitable.

5. DRAIN SELCTOR

Be sure to press the selector knob to ‘WASH’while washing.

CONTROL PANEL WASHING PROCEDURE

FRONT PANEL

REAR PANEL

1.WATER SELECTOR

During washing, WATER SELECTOR KNOB

should be selected to wash. During spin rinsing,

WATER SELECTOR KNOB should be selected to spin.

2.WASH TIMER

This is used to set the wash time, 1-15 minutes.

3.WASH SELECTOR

You can wash laundry effectively by various methods.

Before starting washing, ; Connect the water supply hose and open the water tap.

check the following - Lay the drain hose down toward a sinkhole.(In case no drain pump)

- Place the drain hose in sink or bath.(In case drain pump)

- Connect the power cord to the power supply outlet .

1. Set the CYCLE SELECTOR KNOB to

‘WASH.RINSE’.(in case drain pump ‘WASH’)

5. Put the cloths into

the wash tub and

set the same water

pressure to fill the

tub so as not to

exceed ‘H3’level.

6. Set the WASH TIMER

1-15minutes.

7. After washing, set the

CYCLE SELECTOR KNOB

to ‘DRAIN’ for drain.

2. Set the WATER SELECTOR

KNOB to WASH .

3. Select the

WASH SELECTOR KNOB

for desired mode.

TO WASH

SW-903(P)

4. Fill water in the wash

tub to the‘L1’ lower

water level by carefully

adjusting the tap water

and add the detergent.

1. Select the WASH CONTROL KNOB

for desired mode.

5. Set the WASH TIMER

1-15minutes.

6. After washing Press the

DRAIN SELECTOR KNOB to

‘DRAIN’ for drain .

2. Press the

DRAIN SELECTOR KNOB

to ‘WASH’ .

3. Fill water in the wash tub

to the ‘L1’ lower water

level by carefully

adjusting the tap water

and add the detergent.

4. Put the cloths into the

wash tub and set the

same water pressure

to fill the tub so as not to

exceed ‘H3’level.

(A)Type

(B)Type

SWT90C1(P) / SWT90C2(P)

SWT10H0(P) /SWT10H1(P) /SWT10H2(P)

(A)Type

3. As soon as the WASH TIMER

shuts off, turn off the water tap.

ADDITIONAL RINSE (SHOWER RINSE FOR )

WASHING PROCEDURE

5 6

SPIN DRY

Set the WATER SELECTOR KNOB to

SPIN and CYCLE

SELECTOR KNOB to

‘DRAIN’.

1. Transfer the clothes into the spin basket

and arrange the clothes evenly.

RINSING

OVER FLOW RINSE

3. As soon as the WASH TIMER

shuts off, turn off the water tap.

1. Keep suppling water(adjust water pressure

to ensure that the amount of water supplied

does not exceed that water drained.)

2. Set the WASH

TIMER 6~8minutes.

4. Set the CYCLE

SELECTOR KNOB

to ‘DRAIN’.

3. Close the spin dryer lid.

4. Set the SPIN DRY TIMER 1-5minutes.2. Be sure to attach the safety cover and

close the inner lid.

inner lid

safty cover

inner lid

safety cover

1. Keep suppling water(adjust water pressure

to ensure that the amount of water supplied

does not exceed that water drained.)

2. Set the WASH

TIMER 6~8minutes.

4. Press the DRAIN SELECTOR

KNOB to ‘DRAIN’.

After rinsing you can select this

course for more effective rinse

(Don't select only this course

for rinse.) Load the laundry

evenly into the spin basket.

Supply water for about 1minute.

Adjust the water flow to prevent

overflow from the wash tub.

After stopping water

supply, cover the

laundry with safety cover

and close the inner lid.

Close the spin dryer

lid.

Set the SPIN DRY

TIMER 2~3 minutes.

1. Set the CYCLE SELECTOR KNOB to

‘WASH.RINSE’.(In case drain pump ‘WASH’)

5. Repeat this cycle until drain water

is clean. (2~3 cycle)

2. Supply the proper amount of water as not

to overflow the top of the washing tub.

3. Set the WASH TIMER

2~3minutes.

4. Drain the water.

Set the CYCLE SELECTOR

KNOB to ‘DRAIN’

1. Press the DRAIN SELECTOR

KNOB to ‘WASH’.

5. Repeat this cycle until water

becomes clean.(2-3cycle)

2. Supply the proper amount

of water as not to overflow

the topof the washing tub

and put the laundry

into the washing tub.

3. Set the WASH TIMER

2-3 minutes.

4. Drain the water.

Press the DRAIN SELECTOR

KNOB to ‘DRAIN’.

(A)Type (B)Type

WATER

LEVEL

Low(44l)

Middle(56l)

High(67l)

TROUBLE

The washer

does not work.

Clothes will

not move freely.

Incomplete

spinning

TROUBLE

Incomplete

draining

The spin dryer

basket will not

run.

CHECK POINT

Check that the power cord is

connected to a power outlet well.

Power stoppage?

Is the laundry overloaded?

Are the laundry arranged evenly?

AMOUNT OF CLOTHES

INSTALLATION

Leave some space

Space at last 15cm between the washer

and the wall.

Place the washer on a sturdy flat surface.

If the washer is placed on an uneven or weak

surface, noise or vibration may be occured.

(Allowable is 2˚)

Never install the washer near water.

Do not place the washer in steamy rooms or

where the washer is directly exposed to rain.

Moisture may destroy the electrical insulation

and cause an electrical shock hazard.

Avoid direct sunlight or heating devices.

As plastic and electrical components are

affected by direct heat, never place the

washer near heaters, boilers,etc.

Do not place under direct sunlight.

CHANGING THE POSITION OF THE DRAIN HOSE

Before attempting to change the position of the drain hose,

disconnect the plug from the outlet.

1. Route the drain hose inside the machine.

2.Take out the drain hose from the opposite hole and

insert the drain hose into the hose holder.

LAUNDRY GUIDE

MAINTENANCE

TROUBLE SHOOTING

CLEANING THE MACHINE

7 8

ENVIRONMENT

SPIN DRY TIME

DETERGENT

1. OVERFLOW FILTER

Pull the upper side of the

overflow filter with

your fingers into the holes

in the direction of arrow as

shown in the figure.

2. CLEANING THE FILTER

Pull the overflow filter out and take up the filter

by removing 3 screws as shown in figure.

Wash the filter and washing tub.

WHEN YOU LOAD THE LAUNDRY INTO

THE SPIN BASKET.

Press the laundry evenly and put the safety

cover into the spin basket drum as shown in

the figure.

TO PICK OUT THE CLOTHING WHICH HAS

FALLEN BETWEEN THE BASKET AND TUB.

For safty, pull the power supply plug out of the socket.

3. CLEANING THE WASHER BODY

Wipe off strains on the cabinet and operation panel with soft cloth.

Do not use benzene,thinners,cleanser,or wax, nor scrub the washer with a brush.

Painted surfaces or plastic parts will be damaged.

Water Level

Shirts(Synthetics)

Under Shirts(Cotton)

Working clothes(Cotton)

Low

22 Pieces

38 Pieces

16 Pieces

Middle

29 Pieces

48 Pieces

20 Pieces

High

35 Pieces

58 Pieces

25 Pieces

TIME

1min.

1~2min.

3~5min.

5min.

AMOUNT OF

DETERGENT

44g

56g

67g

TYPE OF LAUNDRY

Thin(synthetic fiber)

wool

cotton

thick(cotton)

-The amount of detergent is average.

Follow the instruction detergent printed on the package for

amount of detergent.

-Choose the amount of detergent depending on the fabric type.

CHECK POINT

Is the filter clogged

with lint?

● See “Cleaning the

machine”on page 7.

Is the spin dryer lid closed

completely?

Are laundry(socks,etc.)falling

out of the spin dryer basket and

clinging to the axle?

● See “To pick out...”on

page 8.

70~80cm

Place a rag under the washer filter

not to wet the floor.

Rotate the filter counterclockwise

and pull out the filter.

3. Remove dirts and rotate

the filter clockwise until it

locks in position.

Rag

Open

Filter

HOW TO CLEAN THE FILTER (In case drain pump)

1.Disassemble two screws from the spin dryer hatch.

2.Pull up the spin dryer hatch to remove it.

3.Remove the clothing.

4.Close the spin dryer hatch.

Install the drain hose about

70~80cm above the ground

for pump model.

Hose holder

Owner’s Instructions

SW-903(P)/SWT90C1(P) / SWT90C2(P)

SWT10H0(P) /SWT10H1(P) /SWT10H2(P)

IF YOU NEED HELP.

Do not hesitate to call your local samsung service center.

They will be willing to help you.

Be sure to give them your name,address,telephone number and the purpose of the call.

BEFORE USING THE WASHER 1

CAUTIONS 1

PRECAUTIONS WHEN OPERATING 1

DESCRIPTION OF PARTS 2

CONTROL PANEL 3

WASHING PROCEDURE 4

TO WASH 4

SPIN DRY 5

RINSING 5

OVER FLOW RINSE 6

ADDITIONAL RINSE 6

INSTALLATION 7

ENVIRONMENT 7

CHANGING THE POSITION OF THE DRAIN HOSE 7

HOW TO CLEAN THE FILTER 7

CLEANING THE MACHINE 7

LAUNDRY GUIDE 8

MAINTENANCE 8

TROUBLESHOOTING 8

SPECIFICATIONS

SPECIFICATION

Before operating the unit, please read this manual

throughly, and retain for future reference.

W820mm x D524mm x H1000mm W820mm x D524mm x H920mm W820mm x D524mm x H993mm

0.05~0.78 MPa

0.5 ~ 8.0 kg .f/ cm2

36 kg

50 %

Low : 44lMiddle : 56lHigh : 67l

Washing:7.0kg Spinning:6.5kg Washing:7.0kg Spinning:6.5kg Washing:8.0kg Spinning:6.5kg

Washing:400W Spinning:200W Washing:580W Spinning:200W Washing:400W Spinning:200W

600W 790W 600W

Washing : 1Hour Spinning : 15minutes

SWT90C1(P) / SWT90C2(P) SW-903(P)

SWT10H0(P)/SWT10H1(P)/SWT10H2(P)

DIMENSIONS (mm)

WATER PRESSURE

WEIGHT

EXTRACTION EFFICIENCY

STANDARD QUANTITY OF WATER

CAPACITY

(Maximum dry mass textiles)

MOTOR INPUT

MOTOR MAX INPUT

RATING TIME

CODE NO : DC68-01293A

This manual suits for next models

Table of contents

Other Samsung Washer manuals

Samsung

Samsung WA80HA User manual

Samsung

Samsung WW70J4 Series User manual

Samsung

Samsung S1043(V/S/C) Use and care manual

Samsung

Samsung WD1102XVM User manual

Samsung

Samsung WF350ANR/XAA User manual

Samsung

Samsung B1445AVGW/YLW User manual

Samsung

Samsung S1003J User manual

Samsung

Samsung H146HWB User manual

Samsung

Samsung H1255A User manual

Samsung

Samsung WA10J571 Series User manual

Samsung

Samsung WF42H5700A Series Manual

Samsung

Samsung WF511AB series User manual

Samsung

Samsung WA44A32 A Series User manual

Samsung

Samsung SW75V9W User manual

Samsung

Samsung WD11T Series User manual

Samsung

Samsung WD75K6 Series User manual

Samsung

Samsung WW9 T Series User manual

Samsung

Samsung WF8694FF User manual

Samsung

Samsung SW80SP User manual

Samsung

Samsung B1045A(V/S/C) User manual

Samsung

Samsung Q1044A User manual

Samsung

Samsung M801 User manual

Samsung

Samsung WA50R5400 Series User manual

Samsung

Samsung SW12E1S(P)/XST User manual

Popular Washer manuals by other brands

Tricity Bendix

Tricity Bendix AW 1000 W Operating & installation instructions

Panasonic

Panasonic NA-F60L5WRB operating instructions

GE WSLP1500 Dimensions and installation information

Electrolux

Electrolux EWF1284EDW Service manual

Bosch

Bosch WAN2829BSN User manual and installation instructions

LG TV2516DV3B owner's manual

LG TH2517DSAV owner's manual

VESTEL

VESTEL CMH-XL 7510 TE user manual

AEG

AEG 74335 User information

Johnson

Johnson JWF721A user manual

Beko

Beko WTE7604XLW0 owner's manual

Danby

Danby DTT100A1WDB Owner's use and care guide

Amica

Amica WA 14 Ex operating instructions

Daewoo

Daewoo DWD-F1222 instruction manual

Bosch

Bosch WAS28461AU instruction manual

Miele

Miele PW 6080 Vario manual

Finlux

Finlux FLX108CF220 user manual

Whirlpool

Whirlpool 3LBR5132AN0 Use and care guide