Samsung NE58R9560WG User manual
This manual is made with 100 % recycled paper.
Electric Range
installation manual
imagine the possibilities
Thank you for purchasing this Samsung product.
Manual Install_NE58H9970WS_AA_AC_DG68-00594A-00_EN.indd 1 15/05/2014 10:13:35
contents
PREPARING TO INSTALL THE
RANGE
3
3 About this section
3 For your safety
4 Remove packaging
4 Prepare tools & Parts
5 Checking the installation site
7 To avoid breakage
CONNECTING THE POWER
8
8 Step 1. Meeting electrical
connection requirements
9 Step 2. Accessing the power cord
connection
10 Step 3. Installing the power cord
12 Step 4. Installing the conduit
15 Step 5. Replacing the access cover
INSTALLING THE RANGE
16
16 Installing the anti-tip device
18 Finalizing the installation
18 Optional rear filler kit
English - 2
Manual Install_NE58H9970WS_AA_AC_DG68-00594A-00_EN.indd 2 15/05/2014 10:13:35
preparing to install the range
ABOUT THIS SECTION
READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY.
Important note to the installer
• Read all instructions contained in these installation instructions before installing
the range.
• Remove all packing materials from the oven compartments before connecting the
electrical supply to the range.
• Observe all governing codes and ordinances.
• Be sure to leave these instructions with the consumer.
Important note to the consumer
Keep these instructions for the local electrical inspector’s use.
• As when using any appliance generating heat, there are certain safety precautions
you should follow.
• Be sure your range is installed and grounded properly by a qualified installer or
service technician.
• Make sure the wall coverings around the range can withstand the heat generated
by the range.
• To eliminate the need to reach over the surface elements, avoid having cabinet
storage space above the cooktop.
• The range should not be placed on a base.
FOR YOUR SAFETY
WARNING
WARNING If the information in this manual is not followed exactly, a
fire or electrical shock may result causing property damage, personal injury, or death.
WARNING
WARNING Before beginning the installation, switch the power o at
the service panel and lock the service disconnecting switch to prevent power from being
switched on accidentally. When the service disconnecting switch cannot be locked,
securely fasten a prominent warning device, such as a tag, to the service panel.
WARNING
WARNING This appliance must be properly grounded.
English - 3
01 PREPARING TO INSTALL THE RANGE
Manual Install_NE58H9970WS_AA_AC_DG68-00594A-00_EN.indd 3 15/05/2014 10:13:35
REMOVE PACKAGING
Remove the packaging materials. Remove the supporter frame located on the back
of the cooktop glass. Failure to remove packaging materials could result in damage
to the appliance.
PREPARE TOOLS & PARTS
The tools you will need
Drill Adjustable Wrench Pliers 1/4˝ Nut Driver
Phillips Screwdriver Flat Screwdriver Pencil Level
What’s included with your range
Template Anti-Tip Bracket Screws (short:2 ea,
long:2 ea)
Filler Kit & Screws
(3 ea)
Additional materials you may need
4-Wire Cord or 3-Wire Cord
(UL Approved 40 or 50 AMP)
Strain Relief
(For Conduit Installation Only)
English - 4
Manual Install_NE58H9970WS_AA_AC_DG68-00594A-00_EN.indd 4 15/05/2014 10:13:37
CHECKING THE INSTALLATION SITE
Clearances and dimensions
To install the range, refer to the following figure.
CAUTION
CAUTION This range has been designed to comply with the maximum
allowable wood cabinet temperatures of 194 °F. Make sure the wall covering,
countertops, and cabinets around the range can withstand the heat (up to 194 °F)
generated by the range. If not, discoloration, delamination, or melting may occur.
A
B
36”~36-4/5”
31”
29-4/5” 26-3/10”
Hatched Faces should be
flat and leveled.
35-7/8” 23-3/16”
1/2” min.
25”
6”
3”
24”
3”
1” min.
23-1/5” A :
Cabinet opening
29-15/16”~30-1/16”
(76.04 - 76.28 cm)
B : Acceptable
electrical outlet
area
* If your cabinets are over 36-4/5” high, you must install this range on a hard, heat
resistant support that raises the surface of the range so that it is about even with
the countertop.
English - 5
01 PREPARING TO INSTALL THE RANGE
Manual Install_NE58H9970WS_AA_AC_DG68-00594A-00_EN.indd 5 15/05/2014 10:13:37
Minimum dimensions
IMPORTANT To eliminate the risk of burns or fire caused by reaching
over heated surface units, avoid having cabinet storage space located above the surface
units. If you have cabinet storage space over the heating elements, you can reduce the
risk by installing a range hood that projects horizontally a minimum of 5 inches beyond
the bottom of the cabinets.
* 30”
30”
** 15”
* A minimum of 30” is required
between the top of the
cooking surface and the
bottom of an unprotected
wood or metal cabinet; a
minimum of 24” is required
if the bottom of the wood or
metal cabinet is protected
by not less than 1/4” of flame
retardant millboard covered
with not less than no.28
MSG of sheet steel, 0.015”
of stainless steel, 0.024”
of aluminum, or 0.020” of
copper.
** A minimum of 15” is required
between the countertop and
the adjacent cabinet bottom.
English - 6
Manual Install_NE58H9970WS_AA_AC_DG68-00594A-00_EN.indd 6 15/05/2014 10:13:38
TO AVOID BREAKAGE
CAUTION
CAUTION Do NOT lift or handle the unit by the cooktop glass.
Fig. 1
C1
C3
C2
C4
1. The counter top around the cut-out should be flat and leveled (see hatched area on
Fig. 1).
2. Before installing the unit, measure the heights of the two cabinet sides (C1~C4),
front and back (See Fig. 1) from the floor to the top of the counter.
3. Level the range using the four leveling legs so that the height from the floor
to the underside of the cooktop glass frame is greater than the tallest cabinet
measurement by at least 1/16”.
4. Remove the Support Frames on the back left and back right of the glass cooktop
(Refer to page 4).
5. Slide the unit into the cabinet (DO NOT PUSH THE UNIT HARD). Make sure the
center of the unit aligns with the center of the cabinet cut-out.
6. The cooktop glass frame under the cooktop glass MUST sit above the cabinet
countertop so the unit is supported by its leveling legs. The cooktop glass should
NOT directly touch the countertop If the cooktop glass is touching the countertop,
it could break, voiding the warranty.
IMPORTANT MAKE SURE the unit is supported by the leveling legs
and NOT by the cooktop itself. The cooktop glass must sit above the surface of the
countertops.
English - 7
01 PREPARING TO INSTALL THE RANGE
Manual Install_NE58H9970WS_AA_AC_DG68-00594A-00_EN.indd 7 15/05/2014 10:13:38
connecting the power
STEP 1. MEETING ELECTRICAL CONNECTION
REQUIREMENTS
CAUTION
CAUTION For personal safety, do not use an extension cord
with this appliance. Remove the house fuse or open the circuit breaker before
beginning installation.
This appliance must be supplied with the proper voltage
and frequency, and be connected to an individual, properly
grounded branch circuit, protected by a circuit breaker or fuse
having amperage as specified on the rating plate. The rating
plate is located above the drawer on the oven frame. (Fig. 1 or
Fig. 2)
We recommend you have the electrical wiring and hookup
of your range connected by a qualified electrician. After
installation, have the electrician show you where your main
range disconnect is located.
Check with your local utilities for electrical codes which apply
in your area. Failure to wire your oven according
to governing codes could result in a hazardous
condition. If there are no local codes, your range must
be wired and fused to meet the requirements of the
National Electrical Code, ANSI/NFPA No.
70–Latest
Edition. You can get a copy by writing:
National Fire Protection Association
Batterymarch Park
Quincy, MA 02269
Eective January 1, 1996, the National Electrical Code requires that new
construction (not existing) utilize a 4-conductor connection to an electric
range.
When installing an electric range in new construction, follow Steps 2 and 3
for a 4-wire connection.
You must use a 3-wire or 4-wire, single-phase A.C. 208Y/120 Volt or 240/120 Volt,
60 hertz electrical system.
If the electrical service provided does not meet the above specifications, have a
licensed electrician install an approved outlet.
Use only a 3-conductor or a 4-conductor UL-listed range cord. These cords may be
provided with ring terminals on the wire and a strain relief device.
(Fig. 1)
(Fig. 2)
English - 8
Manual Install_NE58H9970WS_AA_AC_DG68-00594A-00_EN.indd 8 15/05/2014 10:13:39
A range cord rated at 40 amps with 125/250 minimum volt range is required. A 50
amp range cord is not recommended but if used, it should be marked for use with
nominal 13⁄8” diameter connection openings. Care should be taken to center the
cable and strain relief within the knockout hole to keep the edge from damaging the
cable.
• Because range terminals are not accessible after the range is in position, a flexible
service conduit or cord must be used.
NOTE If conduit is being used, go to Step 4 on page 12.
ALL NEW BRANCH-CIRCUIT CONSTRUCTIONS, MOBILE HOMES,
RECREATIONAL VEHICLES, AND INSTALLATIONS WHERE LOCAL
CODES DO NOT ALLOW GROUNDING THROUGH NEUTRAL,
REQUIRE A 4-CONDUCTOR UL-LISTED RANGE CORD.
STEP 2. ACCESSING THE POWER CORD CONNECTION
Loosen and then remove the rear access cover screw with a screwdriver. Remove
the rear access cover by lifting it up and then out. The terminal block will then be
accessible.
Access cover
Terminal block
Specified power-supply-cord kit rating
Range rating, watts Specified rating of
power-supply-cord
kit, amperes
Diameter (inches) of range
connection opening
120/240 volts
3-wire
120/208 volts
3-wire Power cord Conduit
8,750 - 16,500 7,801 - 12,500 40 or 50 A 13/8” 11/8”
For power cord installations, go to page 10. For conduit installations, go to page 12.
English - 9
02 CONNECTING THE POWER
Manual Install_NE58H9970WS_AA_AC_DG68-00594A-00_EN.indd 9 15/05/2014 10:13:39
STEP 3. INSTALLING THE POWER CORD
For power cord installations, hook the strain relief over the power cord hole (13/8”)
located below the rear of the drawer body. Insert the power cord through the strain
relief and tighten the device.
Strain relief
Power cord
Conduit connection plate
• You must install the power cord with a strain relief.
• Attach the strain relief to the 13/8” opening in the conduit connection plate.
Installing a 3-wire power cord
WARNING
WARNING
The neutral or ground wire of the power cord must be
connected to the neutral terminal located in the center of the terminal block. The power
leads must be connected to the lower left and the lower right terminals of the terminal block.
1. Remove the 3 lower terminal screws
from the terminal block.
2.
Insert the 3 terminal screws through
each power cord terminal ring and into
the lower terminals of the terminal block.
Be certain that the center wire (white/
neutral) is connected to the center lower
position of the terminal block.
3. Tighten screws securely to the terminal
block. DO NOT remove the ground
strap connection.
4. Go to Step 5 on page 15 to continue
with the installation.
Ground strap
Neutral
terminal
Black
White
Red
Black White
Red
English - 10
Manual Install_NE58H9970WS_AA_AC_DG68-00594A-00_EN.indd 10 15/05/2014 10:13:40
This manual suits for next models
1
Table of contents
Languages:
Other Samsung Range manuals
Samsung
Samsung NE59 431 Series User manual
Samsung
Samsung NE63A6751SG User manual
Samsung
Samsung FTQ387LWGX User manual
Samsung
Samsung NE63-6515S Series User manual
Samsung
Samsung NX60A6751SS User manual
Samsung
Samsung NX58J7750S series User manual
Samsung
Samsung NX60 8 Series User manual
Samsung
Samsung NSE6D 81 Series User manual
Samsung
Samsung Chef Collection NX36R9966PS/AA User manual
Samsung
Samsung NX58K7850S SERIES User manual
Samsung
Samsung NSE6D 87 Series User manual
Samsung
Samsung NE58K9850 Series User manual
Samsung
Samsung NE59J7630SS User manual
Samsung
Samsung NX58K9500W Series User manual
Samsung
Samsung NY36R9966PS/AA User manual
Samsung
Samsung NY58J9850WS User manual
Samsung
Samsung NX5837750SS User manual
Samsung
Samsung NE5937630 Series User manual
Samsung
Samsung NE595R0ABBB User manual
Samsung
Samsung NE599N1PBSR User manual
