Samsung SC-148A User manual

Index

Main Pa

Safet

Precautions

Notational

Installation

While Operating

Other

Usin

the Drive

Using the CD-ROM Drive

Storing and Cleaning Your Discs

Upgrading the Firmware Flash Memory

System Requirements

Introduction

Front

Rear

Troubleshootin

Solving Technical Problems

Setu

Installing the CD-ROM Drive

Connecting the Cables

Installing the Device Driver

Setting Up the Device Driver

ecifications

Safety Precautions

Notational

Warning / Caution

Warning : This symbol indicates explanations about extremely dangerous matters.

If users ignore this symbol and handle the device the wrong way, serious injury or death could

result.

Caution : This symbol indicates explanations about dangerous matters.

If users ignore this symbol and handle the device the wrong way, damage to home or property

could result.

Notational

Failure to follow directions noted by this symbol could result in bodily harm or damage to

equipment.

Prohibited

Important to read and understand at all times

Do not disassemble

Any change or modification not expressly approved by designated qualified personnel could void your

authority to operate this device.

Always make sure that the disc does not have a crack before use. If the disc has a crack (especially

around the center hole), it is recommended to make a copy immediately and use the copy instead.

When a cracked disc is used continuously, the size of the crack is likely to grow and this will eventually

result in irreparable damage to the disc.

Important to read and understand at all times.

Safety Precautions

Installation

Safety Precautions

Installation

Place the drive on a level surface.

-Failure to do so may cause the device to fall onto a hard surface,

resulting in damage or malfunction.

Do not place the drive in direct sunlight.

void low- or high-temperature environments.

void high-humidity environments.

Safety Precautions

While Operating

Handle with caution to prevent damage from external shock.

Do not drop the drive, and protect it fromsevere shocks.

- It can damage the drive or cause it to malfunction.

Do not move the drive while in operation and do not attempt to open

the disc tray byforce.

Make sure to close all working programs before attempting to open the

tray and always usethe open/close button.

- Do not insert a pin into the emergency opening while in operation.

Do not use cracked, distorted or damaged discs.

- In particular, a disc with a crack on the inner tracks may break while in

use.

Safety Precautions

Other

Never allow food particles or foreign substances to enter the drive

casing.

To protect against the risk of fire, do ot spill such liquids as

alcohol and benzene on the drive.

Do not disassemble, attempt to repair or modify the device

without express approval as directed in the manual.

- To reduce the risk of damage, electric shock, and fire,

Introduction

Front

1. Headphone Connector

The sound output terminal enables you to plug stereo headphones into the drive. It requires a 3.6 mm

stereo mini-jack.

2. Headphone volume control

This headphone volume control adjusts the volume for your headphones. You can only use the

headphone jack and volume control when you have installed the required software utilities. For example,

the Microsoft Windows Media player can be used.

3. Disc compartment

The compartment opens and closes automatically when you press the Eject button.

4. Emergency eject hole

If the compartment does not open when you press the Eject button, power off the computer, insert a pin or

unfolded paper clip in the hole and push firmlhy)

5. LED

6. Eject Button

Design and specifications are subject to change without prior notice.

IntroductionIntroduction

Rear

1. Digital output terminal

You can connect a sound card or MPEG card which support Digital output terminal to your drive using this

two-pin terminal.

2. Sound output terminal

You can connect a sound card to your drive using this four-pin terminal.

This function is not covered in detail in this guide. Refer to the documentation supplied with your sound

card.

3. Master/slave select terminal

Usually, this is a pre-set configuration as illustrated below.

Verify that the setting is as illustrated. If it is not, simply remove the jumper and place it in the correct

position.

4. Interface terminal

This input/output interface terminal is used to connect the 40-pin flat cable from the IDE interface to the

CD-ROM drive.

5. Power terminal

The power terminal is a four-conductor male plug.

(A : +5V DC)

(B : +12V DC)

SetupSetup

To install your CD-ROM Drive in the PC, proceed as follows.

Make sure that the PC is powered off and disconnected from any power source.

If necessary, attach a horizontal bracket to both sides of the drive.

Remove the cover from a free expansion slot and install the CD-ROM drive, as shown in the

illustration.

Installing the CD-ROM Drive

Connecting the Cables

Setup

Connecting the power cable

The 4-pin power cable from the internal power unit of your computer must be connected to the power

terminal on the rear of the CD-ROM drive.

A - Cut Side

1+5V DC

2Ground

3Ground

4+12V DC

Note: An improperly connected power cable may cause trouble. Check the direction of the power connector

and the incline side of the CD-ROM drive before connecting.

Connecting the IDE cable

Insert the IDE cable (40-pin), which is connected to the hard disk to the interface terminal.

(Place the red line of the cable close to the Pin 1.)

When using one IDE cable

Connect the cable to the SL (Slave) of the Master/Slave Select Terminal at the rear of the CD-ROM

drive.

a: Slave Drive (Choose the SL Jumper)

b: Hard Drive

c: MainBoard

When using two IDE cable

If there is only one CD-ROM drive, select MA (Master).

Setup

a: Master Drive (Choose the MA Jumper) b: Hard Drive

c: MainBoard d: Primary 1

e: Secondly 1

If there is two CD-ROM drive, select MA (Master) / SL (Slave).

a: Master Drive (Choose the MA Jumper) b: Slave Drive (Choose the SL Jumper)

c: Hard Drive d: MainBoard

e: Primary 1 f: Secondly 1

Installing a jumper on the master/slave select terminal

Connect a jumper to the rear side of the CD-ROM.

If the jumper is connected to MA (Master), it will work in the Master mode.

If the jumper is connected to SL (Slave), it will work in the Slave mode.

If the jumper is connected to CS (CSEL), you can control the device by using the host interface signal

CSEL. (In general, connection to MA is recommended.)

Connecting the audio cable from a sound card

Connect the 4-pin audio cable between the sound output terminal on the CD-ROM drive and the

audio input terminal on the sound card.

For clearer sound, use a digital output terminal.(Available only for the CAID that supports digital

output) This may not be available for general sound cards.

Other manuals for SC-148A

Table of contents

Other Samsung CD/CDR Drive manuals

Popular CD/CDR Drive manuals by other brands

Philips

Philips CDD3610 user manual

QPS

QPS Que!Fire installation manual

LG GCC-4241N Service manual

Plextor

Plextor 12X-3 Using

Teac

Teac CD-211E user manual

SmartDisk

SmartDisk Firewire CD-R/W user guide

Axis

Axis CD-ROM SERVER Quick installation guide

LG CRD-8322B owner's manual

Memorex

Memorex 32023234 - 52x32x52x External USB2.0 CD... Hardware guide

Yamaha

Yamaha CD Recordable/Rewritable Drive CRW3200 owner's manual

Sony

Sony CRX230AE Product information

Sony

Sony CRX - 160E user guide

Panasonic

Panasonic KX-LD742 operating instructions

Pioneer

Pioneer BDR-S13U-X owner's manual

Panasonic

Panasonic LK-MC606BP Operation manual

Panasonic

Panasonic CF-VCW Series operating instructions

LG CRD-8320B owner's manual

Conner

Conner CFP2107 Series product manual