Ricoh MP6200S User manual
i
NOTICE
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate ra-
dio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communication.
However, there is no guarantee that interference will not occur in a particular
installlation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
--- Reorient or relocate the receiving antenna.
--- Increase the separation between the equipment and receiver.
--- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
--- Consult the dealer or an experienced radio / TV technician for help.
FCC WARNING
Changes or modification not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
CAUTION
Use of controls or adjustments or performance of procedures other than
those specified herein may result in hazardous radiation exposure.
a Pay careful attention not to let the invisible laser beam emitted from the
optical pickup enter into your eyes.
b When you find a troubled state of the component in the optical pickup
containing the laser diode, change to the specified new optical pickup.
Do not open the optical pickup housings.
ii
Akustischer Geräuschpegel
Dieser Drucker überschreitet einen Geräuschpegel von 70 dB (A) während
dem Betrieb nicht.
Declaration of Conformity
“The Product complies with the requirements of the EMC Directive
89/366/EEC and the Low Voltage Directive 73/23/EEC.”
iii
Please take notice that the manufacturer of this equipment does not
offer any warranty against data loss due to inappropriate installation
or handling, or direct or indirect damages.
Please take notice that the manufacturer will bear no responsibility
for direct or indirect damages caused by the use of this product or its
malfunction.
Please take notice that the manufacturer will bear no responsibility
for damage to data caused by this product.
Please backup (copy) all important data as protection against data
loss.
PC DOS is a trademark of IBM Inc.
MS-DOS, Windows, and Windows95 are trademarks registered in
the United States and other countries by the Microsoft Corporation.
Adaptec, and the Adaptec logo are trademarks of the Adaptec Cor-
poration.
The company names and product names written in this manual are
trademarks or registered trademarks.
1
Multimedia Printer Series
Ricoh developed the world's first rewritable CD, the CD-Rewritable, and it
has become a commercial success.
The Multimedia Printer Series Drive (the CD-R/RW Drive) can do much more
than read and write the usual CD-R discs. When you load it with a rewritable
CD-RW disc, you can record, read, and edit any kind of data, because these
discs allow you to rewrite information that has already been recorded.
zRicoh's original completely sealed flexible-door construction pro-
vides high reliability.
zRunning OPC*1gives a flatter writing signal that improves reliabil-
ity.
zAn improved anti-heat design means that no cooling fan is needed.
zEasy-to-use tray model.
zUses the world standard SCSI II interface
zCan read not only CD-R and CD-RW discs, but also video CDs,
music CDs, and photo CDs.
zCan read data at 6x speed (900KB/sec data transfer rate) and write
data at 2x speed (300KB/sec data transfer rate).
zThe recorded CD-RW media can be played in a DVD player or
multiread CD-ROM player, maintaining future compatibility.
zSupports random UDF for easy writing to CD-RW discs.
*1 Continuously monitors the signal level during recording and adjusts the
laser power to compensate when the disc is dirty, insuring a flat signal.
Features:
2
The MP 6200SR Series
3
Thank you for purchasing the Multimedia Printer Series (Compact Disc Re-
corder/Rewriter) MP 6200S series (abbreviated CD-R/RW).
Be sure to read this manual carefully before using this product.
This manual explains everything you need to know to operate this product.
Keep it in a safe place and refer to it whenever necessary.
When connecting the CD-R/RW drive, a separate connection kit (SCSI inter-
face) and software (writing software) are needed. For details about the con-
nection kit and software, refer to the manuals for each one.
The MP 6200SR series is an easy-to-use drive.
SCSIinterface
Disc tray model
Random UDF support
CD-Rewritablecompatible
The MP 6200SR Series
Section 1
The MP 6200SR Series
4
The MP 6200SR Series
2. System environment
This unit can be operated in the system environment explained here.
CPU 80486 DX2-66MHz or beter,
Pentium recommended. (PC/AT compatible)
Memory Windows 95: 16MB or greater.
Windows NT4.0:32MB or greater.
Adaptec Inc. AHA-154x, 2940, 3940,
recommended.
Hard disk with average access time of
19msec or less, and data transfer speed of
600KB/sec or greater. 75MB or more free
space.(The free space needed for writing
depends on the quantity of data.)
Windows 95,
Windows NT 4.0 (Service Pack 2) or later
Ricoh, Kao, Mitsubishi Chemical, Taiyo Yuden,
MitsuiToatsu,TDKorKodakdiscsarerecommend.
Occasionally the CD-R and CD-RW discs written by the CD-R/RW drive
cannot be read by other CD drives*1. These unreadable discs should be
read using the CD-R/RW drive.
As the power and interface environments on notebook PCs differ from
desktops, the CD-R/RW might not be supported.
The CD-R/RW drive has been confirmed to work in the following envi-
ronment:
CPU: 100-MHzPentium
OS: Windows95
SCSI Interface Card: Adaptec APA-1460A SlimSCSI
Memory: 24MB
*1 The discs written using the CD-R/RW drive might not be readable by CD-
ROMs other than Multi-read compatible (Random UDF compatible) CD-
ROMs.
Multiread compatible (Random UDF compatible) CD-ROMs are:
- CD-ROMs that can read low reflectance discs
- CD-ROMs that support Packet Write.
System
requirements
SCSI
interface
Hard disk
Software
Required OS
CD-R,
CD-RW discs
5
The MP 6200SR Series
3.Drive functions and settings
3.1 Front Panel
Name Function
Disc tray This is the tray for the disc. Place the disc on
the ejected disc tray, then lightly push the tray
(or push the eject button) and the CD will be
loaded.
Don't use force to pull out or push in the
disc tray. This might cause damage to
the loading section of the drive.
Eject button This is the button used to eject or bring in the
disc tray.
Volume control This is used to adjust the output volume of
the headphone jack. It can't be used to adjust
the output volume for the audio output con-
nectors on the rear panel.
Headphone jack This jack is for connecting headphones or
mini-speakers.
Power/Busy indicator This indicator light shines green when power
is on. When the disc tray or disc is being ac-
cessed, the light shines or flashes orange.
Even when a disc is loaded and a disc is not
being accessed, the light shines grean. When
a illegal disc is loaded or some hardware
trouble occurs, the indicator blinks.
Eject button
Disc tray
Headphone jack
Volume control Power/busy indicator
6
The MP 6200SR Series
3.2 Rear panel
Name Function
SCSI ID jumper Used when selecting the SCSI ID number.
Don't use jumpers to change anything be-
sides the SCSI ID, but keep the drive as ini-
tially set (no jumper pins: ID 0). SCSI ID
changes become valid after power is turned
off, then on again.
Installing jumper pins besides the ones
for SCSI ID settings may be the cause of
damage or abnormal drive operation.
SCSI connector Use a 50 pin double-end flat SCSI cable to
connect to the SCSI interface.
Connecting or disconnecting connectors
while power is on may result in a short
circuit, causing damage to the equipment.
When connecting or disconnecting con-
nectors, make sure to turn off the power
beforehand.
Audio output connector Used to connect to the sound card.
Power connector Used to connect to the host computer's power
supply (DC 5V).
Be careful not to reverse the power con-
nector when attaching it. A reversed con-
nection may cause damage to the equip-
ment (not covered by the warranty).
SCSI connector Power connector
Audio output
connector Terminators
SCSI ID jumper
7
The MP 6200SR Series
4. SCSI ID settings
Before installation, set the SCSI ID on the rear panel. A single SCSI interface
can connect with a maximum of seven peripheral SCSI devices. When using
multiple SCSI devices, a different SCSI ID must be set for each of them.
If two peripheral devices use the same SCSI ID number, it will cause
the host computer to operate abnormally or fail to start up.
ON (When the jumper is attached)
OFF (When the jumper is removed)
Before attaching or removing jumpers, make sure the power to the
drive is turned OFF.
Attach the pins as shown in Figure 1. If the pins are attached side-
ways as shown in Figure 2, the drive may be damaged.
Fig. 1 Fig. 2
The pins besides pins 2-4 don't have any function. If jumpers are
attached to them, abnormal operation may result.
Pin no.
Reserve (Fixed OFF)
SCSI ID
Reserve (Fixed OFF)
This manual suits for next models
1
Table of contents
Other Ricoh CD/CDR Drive manuals
Ricoh
Ricoh MP7080A User manual
Ricoh
Ricoh MP7083A User manual
Ricoh
Ricoh MP7060A Series User manual
Ricoh
Ricoh MP9120A User manual
Ricoh
Ricoh MP7125A User manual
Ricoh
Ricoh MP7060S Series User manual
Ricoh
Ricoh MP7120A User manual
Ricoh
Ricoh MP7200A User manual
Ricoh
Ricoh MP5163A User manual
Ricoh
Ricoh MP6200A User manual
Ricoh
Ricoh MP5316DA User manual
Ricoh
Ricoh MP7163A User manual
Ricoh
Ricoh MP7040S Series User manual
Ricoh
Ricoh MP7040A - MediaMaster - CD-RW Drive User manual
Ricoh
Ricoh MP5120A User manual
Ricoh
Ricoh MP8040SE User manual
Ricoh
Ricoh MP7320A User manual
Ricoh
Ricoh MP7240A User manual
Ricoh
Ricoh MP7400A User manual
Ricoh
Ricoh MP7063A User manual
