RADIO FREQUENCY SYSTEMS ®Antennas
Antenna Interface Configuration
Document Reference: 10000000985 Version 2
The APM40 Kits are mounting hardware options to be
used for Base Station antennas up to 2.6 meters length.
The same APM40 can be mounting with 2 different
Antenna interface : Configuration Aand B
Features
Features include:
Basic direct mount kit
Beam sliding tilt mount for mechanical tilt
Scissor tilt option for fixed at mast (or wall) downtilt
Option for azimuth adjustment independent of mast
All kits fully upgradable
Pipe diameter : 60-120 mm, Wall mount option
Mechanical downtilt, depending of antennas
Azimuth adjustment up to +/-30 degrees
Mechanical Specifications
2.8 Max (type of mounting F)
1.8 Min (type of mounting A)
Aluminium, Galvanised steel
Dynamometric Tools
required
19 and 18mm AF socket
10mm AF spanner or socket
Please contact technical support for more information.
Mount kit installation
with antenna
configuration
Refer to the following table to identify mount kits supplied. The packages of the mount kits are marked with the APM
variation. Refer to the relevent Figure in the Instruction for assembly information. The letter designation is
referenced in the antenna model description.
Beam tilt with azimuth upgrade
Beam tilt with scissor upgrade
Beam tilt with scissor and azimuth upgrades
APM40-2, APM40-E2 & APM40-E3
Assembly and Installation
Masonry anchor
(not supplied)
For pipe mounting, bolt front and rear pipe brackets to pipe.
Tighten from front as rear bracket holds nut captive. Refer
to Table 2 for top to bottom mount bracket separation.
Figure 1a : Pipe Mount Installation Figure 1b : Wall Mount Installation
For wall mounting, fix front bracket to wall with appropriate
masonry anchors. Pre-drill holes with centres 134mm
apart, at top to bottom separation shown in Table 2.
TIGHTENING TORQUE VALUES
Unless stated otherwise, the following general
tightening torque values shall be used for metric
hexagon bolts and screws. All bolts must be property
class 4.8 or over.
MAINTENANCE
Under normal conditions, no maintenance is necessary.
However, the antenna should be visually inspected at
regular intervals for damage (e.g. due to lightning strikes,
and falling ice).Periodic checks should be performed to
verify correct torque and bracket clearance settings.
Accessories provided exclusively by RFS.
REFERENCE DATA
Table 1: Item Numbers for the mount Kit Hardware
Please visit us on the internet at http://www.rfsworld.com
Specifications subject to change without notice.
these data at any time without prior notice.
Specifications subject to change without notice.
these data at any time without prior notice.
Direct
Azimuth
Scissor
Scissor+Azimuth
Beam
Beam+Azimuth
S1=Refer to antenna mount
bracket separation for distance
S2=(S1-316) mm
Figure 9: Adjusting Tilt with Beam Assembly
To adjust tilt, loosen top pipe clamp bolts, bolts
through tilt beam, and bolts at antenna bracket
base (as shown by arrows).Slide arm up or down
pipe to achieve tilt. Align Beam mark with
indicator angle. Tighten nuts to lock in position.
(Refer to tightening torque values)
Figure 10: Adjusting Tilt with Scissor Assembly
To adjust tilt, loosen bolts through scissor and tilt
beam. Loosen bolts at base of antenna to allow
rotation (as shown by arrows). Fold or unfold
scissor to achieve tilt angle .Align Scissor mark
with indicator angle. Tighten nuts to lock position.
(Refer to tightening torque values)
1 Screw Hex M12x110
2 Bolt Hex M12x130
3 Bolt Hex M12x65
4 Nuts Hex M12
5 Washer Flat M12
6 Washer Spring M12
7 Screw Hex M6x16
8 Washer Spring M6
9 Washer Flat M6
10 Washer Flat M12 diameter 31,5
11 Stub Spacer arm
Figure 11: Adjusting azimuth tilt
To adjust angle, loosen bolts (as show by arrows)
through azimuth bracket (top and bottom), and rotate to
desired angle. Tighten nuts to lock position.
