Retevis RT28 User manual
Model: RT28 / RT28P
Add: 7/F, 13-C, Zhonghaixin Science&Technology Park, No.12 Ganli
6th Road, Jihua Street, Longgang District, Shenzhen, China
Web: www.retevis.com
E-mail: [email protected]
Facebook: facebook.com/retevis
EU Importer：
Name：Germany Retevis Technology GmbH
Address：Uetzenacker 29,38176 wendeburg
The light turns off when the the
battery is fully chraged.
Use the USB cable to plug to the radio, the orange lights when
charging, while the light turns off indicates it is fully charged.
Instruction Manual (RT28P additional function)
1) Reading: There will be a voice prompt when a patrol radio is about 3
to 5 cm away from the zone in which the checkpoint tag is installed.
2) Communicating: A USB cable can be used for the two-way
communication between your PC and the patrol radio.
10 11
Guard Patrol System (RT28P additional function)
● A patrol personnel goes to the patrol routine and read the checkpoint
along the way with the patrol radio.
● The patrol radio can automatically record the time on the checkpoint.
● After the radio is connected to a PC via a USB cable, collect the data
from radios into the management software.
Patrol
Point
Patrol
Point
Patrol
Point
Patrol
Point
Patrol
Point
Reading
Setting
Uploading
Reading Reading Card reading area
USB Jack
Installation of the software and its driver
1. Download a software and locate its driver program (for the driver-based software)
for your computer operating system ;
2. After the driver was installed, reboot your PC and then install patrol management
software by clicking twice.
Notice & Solution (RT28P additional function)
● Patrol radio can read the checkpoint but cannot communicate with
the computer;
1. Check if the software and driver are installed properly;
2. Check if the port of patrol radio or cable is damaged;
3. Check if the port of patrol or cable is dirty;
● Patrol radio cannot read the checkpoint;
1. Check if the patrol battery is dead. If so, please recharge or replace
the battery.
2. Check the time on the patrol radio and connect it to adjust the time
if need be.
● The patrol radio can read the checkpoint automatically no matter
whether it is on or off.
● The patrol radio will beep when it succeeds reading the card.
● The patrol radio will beep when it is connected or disconnected.
● The patrol radio will beep a while when it is used to read a
checkpoint if the time in radio system is not correct.
Remarks: Patrol system software, Patrol operation instructions, please
find here: https://www.retevis.com/resources-center
12 13
Operating the software (RT28P additional function)
SETP 1
Initializing the device
1. When your patrol radio is connected in sequence to a PC, run the software and
access Read Device > Time Correction (there will be prompt if the time on your
device needs to be corrected) > Wipe Device;
2. Disconnect the device
SETP 2
Caution:
1. When the patrol radio was first used in the system, run the software and access Basic Setting> Patrol Setting to add the information
about corresponding patrol radio.
2. As for Personnel Setting and Event Setting in Basic Setting, you can make selective use of them. The method of configuration is
quite similar to the checkpoint.
3. The function of login is not enabled in the default system setting. If need be, please add user information to User Setting.
Installation of Checkpoint
1. Print the information about checkpoint in the Basic Setting;
2. Install the numbered checkpoints according to the printed sheet;
3. And thus far, the system configuration is completed and the whole system can
work now.
SETP 6
Basic Setting
1. Number the checkpoints in sequence, 1,2,3,4...
2. Use patrol radio A to read the checkpoints successively;
3. Start the software(RETEVIS Patrol System), access Basic Setting > Checkpoint
Setting to import the checkpoints;
4. After you succeed in importing, please edit the name of checkpoint in sequence.
5. Refer to STEP 2, wipe the device;
SETP 3
Patrol Route
1. Run the software, access Patrol Route and increase a patrol route;
2. Select the patrol route, bind the patrol route and its corresponding patrol radios
and checkpoints.;
SETP 4
Patrol Plan
1. Run the software, access Patrol Plan, select desired the route that need to be
set and add your plan;
SETP 5
15
14
This two-way radio uses electromagnetic energy in the radio frequency
(RF) spectrum to provide communications between two or more users
over a distance. RF energy, which when used improperly, can cause
biological damage.
All Retevis two-way radios are designed, manufactured, and tested to en-
sure they meet government-established RF exposure levels. In addition,
manufacturers also recommend specific operating instructions to users
of two-way radios. These instructions are important because they inform
users about RF energy exposure and provide simple procedures on how
to control it.
Please refer to the following websites for more information on what RF
energy exposure is and how to control your exposure to assure
compliance with established RF exposure limits:http://www.who.int/en/
Local Government Regulations
When two-way radios are used as a consequence of employment, the
Local Government Regulations requires users to be fully aware of and
able to control their exposure to meet occupational requirements.
Exposure awareness can be facilitated by the use of a product label
directing users to specific user awareness information. Your Retevis
two-way radio has a RF Exposure Product Label. Also, your Retevis
user manual, or separate safety booklet includes information and
operating instructions required to control your RF exposure and to
satisfy compliance requirements.
1716
interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at
his own expense.
CE Requirements:
• (Simple EU declaration of conformity) Shenzhen Retevis Technology
Co.,Ltd. declares that the radio equipment type is in compliance with
the essential requirements and other relevant provisions of RED
Directive 2014/53/EU and the ROHS Directive 2011/65/EU and the
WEEE Directive 2012/19/EU; the full text of the EU declaration of con-
formity is available at the following internet address: www.retevis.com.
• Restriction Information
This product can be used in EU countries and regions, including:
Belgium(BE), Bulgaria (BG), Czech Republic (CZ), Denmark (DK),
Germany (DE), Estonia (EE), Ireland (IE), Greece (EL), Spain (ES),
France (FR), Croatia (HR), Italy (IT), Cyprus (CY), Latvia (LV),
Lithuania (LT), Luxembourg (LU), Hungary (HU), Malta (MT), Neth-
erlands (NL), Austria (AT), Poland (PL), Portugal (PT), Romaniam
(RO), Slovenia (SI), Slovakia (SK), Finland (FI), Sweden (SE) and
United Kingdom (UK).
For the warning information of the frequency restriction, please refer to
the package or manual section.
Radio License
Governments keep the radios in classification, business two-way radios
operate on radio frequencies that are regulated by the local radio
management departments (FCC, ISED, OFCOM, ANFR, BFTK,
Bundesnetzagentur...).To transmit on these frequencies, you are
required to have a license issued by them. The detailed classification
and the use of your two radios, please contact the local government
radio management departments.
Use of this radio outside the country where it was intended to be
distributed is subject to government regulations and may be prohibited.
Unauthorized modification and adjustment
Changes or modifications not expressly approved by the party responsi-
ble for compliance may void the user’s authority granted by the local
government radio management departments to operate this radio and
should not be made. To comply with the corresponding requirements,
transmitter adjustments should be made only by or under the supervision
of a person certified as technically qualified to perform transmitter
maintenance and repairs in the private land mobile and fixed services
as certified by an organization representative of the user of those services.
Replacement of any transmitter component (crystal, semiconductor, etc.)
not authorized by the local government radio management departments
equipment authorization for this radio could violate the rules.
FCC Requirements:
This device complies with part 15 of the FCC Rules. Operation is subject
to the condition that this device does not cause harmful interference.
(Licensed radios are applicable);
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (Other devices are applicable)
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including
Other manuals for RT28
1
This manual suits for next models
1
Table of contents
Other Retevis Two-way Radio manuals
Retevis
Retevis RB19 User manual
Retevis
Retevis RT24 User manual
Retevis
Retevis RT45 User manual
Retevis
Retevis RT66 User manual
Retevis
Retevis RT78 User manual
Retevis
Retevis RA36 User manual
Retevis
Retevis RT665 User manual
Retevis
Retevis RT45P User manual
Retevis
Retevis H-777 User manual
Retevis
Retevis RT18 User manual
Retevis
Retevis RT29 User manual
Retevis
Retevis RT37 User manual
Retevis
Retevis RB22 User manual
Retevis
Retevis RT42 User manual
Retevis
Retevis RT30 User manual
Retevis
Retevis RT76P User manual
Retevis
Retevis RT10 User manual
Retevis
Retevis RT-388 User manual
Retevis
Retevis RT48 User manual
Retevis
Retevis RT46 User manual
