Regency Classic F1150 User manual

F1150 Wood Stove | 1

F1150 Classic™Small Wood Stove

UNIT DIMENSIONS

21 1

540mm

32 3

831mm

24"

610mm

30 3

772mm

12 7

326mm

17 3

441mm

20"

508mm

6 1

165mm

7 13

199mm

29 11

753mm

32"

813mm

Unit with pedestal

Unit with legs

OUTSIDE AIR DIMENSIONS

Rear

Front

Rear

4-9/16" (115mm)

4-15/16" (126mm)

Rear

Front

Rear

4-9/16" (115mm)

4-15/16" (126mm)

with pedestal with bottom heat shield + legs

Model F1150

Cordwood BTU’s 55,000 BTU’s

Emissions (grams/hr) EPA Certied 1.7 gram/hr

Eciency (EPA HHV)* 70%

Eciency (EPA LHV) 75%

Flue Size 6" (152mm)

US Biomass Tax Rebate Eligible No

Maximum Log Size 18’’ (457 mm)

Firebox Size 1.3 cu.ft.

*US Biomass Tax Rebate eligibility is based on the HHV value being

greater than or equal to 75%.

2 | F1150 Wood Stove

MINIMUM CLEARANCE TO COMBUSTIBLE MATERIALS

Please read the section below carefully as clearances depend on whether single wall or double wall pipe is installed on the stove.

Measurements "From Unit" are from the top plate of the stove to a side wall or to a corner, and from the rear heat shield to a back wall.

Clearances may only be reduced by means approved by the regulatory authority.

Note: Minimum ceiling height - 83" (2108mm)

Note: This clearance is also required for air space between the appliance and wall/ceiling.

NOTE: Be aware that local Codes and

Regulations may override some

clearances listed in this manual.

Check with your local inspector.

ROOF EXIT

WALL EXIT

ROOF EXIT

WALL EXIT

NOTE: Clearances to combustibles are for

the safety of the property. To avoid

overheating and damaging the

appliance these clearances should

be maintained for non-combustibles

also.

Residential Close Clearance (To be installed with required pipe components) Listed Double Wall Pipe

When the stove is installed as a close clearance residential unit, a listed double wall connector is required from the stove collar to the ceiling

level.

F1150 with Airmate or

Rear Deector

A B C D E F

11"

279mm

178mm

127mm

23"

584mm

13-9/16"

345mm

17"

432mm

Residential Installation "C" Vent (Single Wall Pipe)

F1150 with Airmate or

Rear Deector

A B C D E F

13"

330mm

10-1/2"

267mm

229mm

25"

635mm

17-1/16"

433mm

21"

532mm

Mobile Home Close Clearance (To be installed with required pipe components) Listed

Double Wall Pipe

When the stove is installed as a close clearance residential unit, a listed double wall connector is required from the stove collar to the ceiling

level.

Refer to Mobile Home Installation in this manual.

F1150 with Airmate or

Rear Deector

A B C D E F

11"

279mm

178mm

127mm

23"

584mm

13-9/16"

345mm

17"

432mm

F1150 Wood Stove | 3

MINIMUM ALCOVE CLEARANCE AND CLEARANCE TO

COMBUSTIBLE MATERIALS

The Regency Freestanding models have been alcove approved and must be installed

with a listed double wall connector to the ceiling level. Single wall pipe (C Vent) is not

approved for alcoves.

Note: Minimum alcove ceiling height - 83" (2108mm)

Maximum depth of alcove - 36" (914mm)

FLOOR PROTECTION

(EMBER PROTECTION ONLY REQUIRED)

A combustible oor must be protected by a non-combustible material (like tile, concrete board, or certied to UL-1618 Type 1 (or as dened by

local codes).

Canada: Beneath the heater and extending to at least 18" (457mm) on the fuel loading side and at least 8" on the sides and back.

USA: Beneath the heater and extending to at least 16" (405mm) beyond the fuel loading side and ash removal opening and at least 8" (203mm)

on the sides and back and under the chimney connector extending 2" (51mm) beyond each side for horizontal applications.

Note: The measurements for oor protection for both front & sides are taken from the fuel door opening.

Where the appliance is installed less than 8" from a rear wall, the ember pad only needs to extend to the base of the wall based on the clearances

noted in this manual.

NOTE: This clearance is also required for air space between the appliance and

wall/ceiling.

Minimum Overall Depth of Floor Protector

Unit Hearth Depth Edge of Fuel door

opening to edge of

hearth

Hearth Width Edge of Fuel Door

Opening

A B C D

F1150 Canada 42" (1067mm) 18" (457mm) 33-11/16" (932mm) 8" (203mm)

USA 40" (1016mm) 16" (406mm) 33-11/16" (932mm) 8" (203mm)

Unit From Unit From Flue Center-Line From Wall

G H I J K

F1150 with Airmate or Rear

Deector

11" (279mm) 7" (178mm) 23" (584mm) 13-9/16" (345mm) 46" (1168mm)

4 | F1150 Wood Stove

Minimum Overall Depth (Y) of Floor Protector - Corner Hearth

Reference only when hearth pad is installed to rear wall at minimum pipe clearances.

Hearth Depth

F1150 L M N O

Residential Installation ''C'' Vent (Single Wall)

Canada 33-11/16" (856mm) 57-3/16" (1453mm) 48-1/16" (1221mm) 24-1/4" (616mm)

USA 33-11/16" (856mm) 55-3/16" (1402mm) 46-11/16 (1186mm) 22-7/8" (581mm)

Residential Close Clearance (To be installed with required pipe components)

Canada 33-11/16" (856mm) 51-1/2" (1308mm) 44-1/16" (1119mm) 20-1/4" (514mm)

USA 33-11/16" (856mm) 49-1/2" (1257mm) 42-11/16" (1084mm) 18-7/8" (479mm)

16"

for angled corners

FLOOR PROTECTION

(CORNER INSTALLATION)

A combustible oor must be protected by non-combustible

material (like tile, concrete board, or certied to UL-1618 or

as dened by local codes) extending beneath the heater and

a minimum of 8" (203mm) from each side and minimum 16"

(406mm)** from the front face of the stove and minimum 6"

(152mm)** (or the rear clearance to combustibles whichever

is smaller) from the rear of the stove.

When installed with horizontal venting, non-combustible

oor protection must beneath the ue pipe and extend 2"

(51mm) beyond each side.

Minimum Overall Width (X) of Floor

Protector for all installations:

Stove F1150 33-11/16" (856 mm)

**NOTE: In Canada, oor protection must extend 18" (457mm)

to the front and 8" (203mm) to back of the stove.

Minimum Overall Depth (Y) of Floor Protector

Unit Residential

"C" Vent

From Edge of Fuel Door

Opening

Y Z W

F1150 Canada - 42" (1067mm)

USA - 40" (1016mm)

**6" (152mm) 8" (203mm)

F1150 Wood Stove | 5

Pedestal

Bolted to

Floor

Outside Air

MOBILE HOME INSTALLATION

Once you have properly marked the position of

your unit and the oor protection as outlined in

the Residential Installation items #1 through #8, a

supply of fresh air has to be supplied to your unit.

See Optional Outside Air Kit instructions in this

manual.

Place your unit in position and secure it to the

oor using two lag bolts 3/8" (10mm) x 3-1/2"

(89mm) through the two holes inside the pedestal

base. It is important to maintain the structural

integrity of the Mobile Home oor, walls and roof

when installing your unit.

For Mobile Home units installed in the U.S. the

unit must be grounded using a #8 ground wire

with approved termination and star washer.

In addition to standard installation instructions

the following requirements are mandatory for

installation in a mobile home.

1. The stove must be permanently bolted to

the oor of the Mobile Home using the oor

screws provided.

2. The stove must have a permanent outside air

source for combustion.

3. The stove must be electrically grounded to

the steel chassis of the Mobile Home.

4. A listed double-wall connector chimney

system, roof thimble, spark arrestor and roof

ashing kit suitable for use in Mobile Homes

must be used.

5. If the chimney exits the Mobile Home at a

location other than through the roof, and

exits at a point 7ft. (2130mm) or less above

the ground level on which the Mobile Home

is positioned a guard or method of enclosing

the chimney shall be tted at the point of exit

for a height up to 7ft. (2130mm).

6. The chimney shall be attached directly to the

room heater and shall extend at least 3 ft.

(914mm) above the part of the roof through

which it passes. The top of the chimney

should project at least 2ft. (610mm) above

the highest elevation of any part of the Mobile

Home within 10 ft. (3048mm) of the chimney.

7. The chimney system shall comply with Local

Requirements.

8. Any openings in a chimney guard where

required must not permit the entrance of 3/4"

(19mm) diameter rod.

9. CAUTION: THESTRUCTURAL INTEGRITY

OF THE MOBILE HOME ROOF, FLOOR,

WALLS AND CEILING MUST BE

MAINTAINED.

10. Check any other local building code as other

local codes may apply.

11. WARNING: DO NOT INSTALL IN A

SLEEPING ROOM OF A MOBILE HOME.

12. Use silicone to create an eective vapour

barrier at the location where the chimney or

other component penetrates to the exterior

of the structure.

CAUTION: At no time use unlabelled

parts, or substitute parts made for

another chimney system.

Install as per chimney manufacturer's

installation instructions.

For Canadian Installations: see Outside

Air Kit - Part # 846-502.

There are further requirements when installing

this unit into a mobile home in Canada Only.

WARNING: Operate only with door

fully closed - open feed door to feed

re only.

1. Identify the position of the outside air damper by the orientation of

the metal handle that rests outside the galvanized pipe. The metal

handle and the damper disc are in line with each other. This means

that if the metal handle is in a horizontal position, the damper is at

and fully open.

2. Open the damper fully whenever you start a re. This will allow the

outside air to be drawn in the pedestal base eliminating any potential

smoke escaping the stove and entering the room. (Negative air

pressure)

6 | F1150 Wood Stove

MOBILE HOME KIT - FOR CANADA

Note: The optional ashdrawer cannot be used when using the Mobile Home Kit.

919-757a 12.10.19

F1500

Mobile Home Kit - For Canada

Note: The optional ash drawer cannot be used when using the Mobile Home Kit.

3. Remove the 4" knock out from the rear pedestal.

4. Install rear collar to the rear pedestal using 4 screws.

Page 1 of 1 075-500.SLDASM 12/19/2016

Mobile Home Box

Pedestal Stove

Collar

Flex

The Mobile Home kit contains:

1 Bottom metal cover - only used when air is drawn from the ﬂoor.

1 Flex

1 Collar

1 Mobile home box

1 Square transition box (used when installing bottom heat shield/

legs)

Screws

5. Attach ﬂex to rear pedestal using supplied screws or 4" clamp.

6. Bring pedestal base near the base of the ﬁrebox and secure ﬂex

to the Mobile Home box.

7. Secure pedestal base and Mobile Home Box to ﬁrebox as shown

in diagram 3 using the screws that were previously removed/

loosened in step 1. See pedestal instructions.The Mobile Home

Box and ﬁrebox use the same screws.

Diagram 4

8. Install blanking plate to the front of the pedestal with 4 screws.

1. Lay unit on its back. Remove two front 7/16 bolts. Loosen rear

two 7/16" bolts. See diagram 1.

  

Install rear collar

to the rear pedes-

tal using 4 screws.

Diagram 2 4 screws

Diagram 5

9. Place unit into position and install the mandatory outside air kit.

See «Mobile Home installation» section in this manual.

Blanking

plate

2. If using outside air from the rear of the pedestal, follow instruc-

tions noted below. If using outside air from the pedestal base,

follow instructions from step 10 to 16. For bottom heat shield/

legs, follow instructions from step 17 to 22. The Mobile Home

Box is always mounted in between the ﬁrebox and pedestal or

bottom heat shield.

Diagram 1

Diagram 3

F1150 Wood Stove | 7

Horizontal Installation

Standard Ceiling Installation

9. NOTE: Residential Close Clearance

and Alcove installations require a

listed double wall connector from

the stove collar to the ceiling level.

The diagrams below illustrate one way to

install your unit into a standard ceiling or

with a horizontal connector. Check with your

dealer or installer for information on other

options available to you.

STEP-BY-STEP

CHIMNEY AND

CONNECTOR INSTALLATION

Note: These are a generic set of chimney

installation instructions. Always

follow the manufacturers own

instructions explicitly. Check the

Minimum Recommended Flue

Heights section (Table 1).

1. With your location already established, cut

and frame the roof hole. It is recommended

that no ceiling support member be cut for

chimney and support box installation. If it is

necessary to cut them, the members must

be made structurally sound.

2. Install radiant shield and support from above.

3. Stack the insulated pipe onto your nish

support to a minimum height of 3 feet above

the roof penetration, or 2 feet above any

point within 10 feet measured horizontally.

There must be at least 3 feet of chimney

above the roof level.

Note: Increasing the chimney height above

this minimum level will sometimes

help your unit to “breathe” better

by allowing a greater draft to be

created. This greater draft can

decrease problems such as, dicult

start-ups, back-smoking when door

is open, and dirty glass. It might

be sucient to initially try with the

minimum required height, and then

if problems do arise add additional

height at a later date.

4. Slide the roof ashing over your chimney

and seal the ashing to the roof with roong

compound. Secure the ashing to your roof

with nails or screws.

5. Place the storm collar over the ashing,

sealing the joints with a silicone caulking.

6. Fasten the raincap with spark screens (if

required) to the top of your chimney.

7. To complete your chimney installation, install

the double wall connector pipe from the

stove’s ue collar to the chimney support

device.

8. If you are using a horizontal connector,

the chimney connector should be as high

as possible while still maintaining the 18"

(457mm) minimum distance from the

horizontal connector to the ceiling.

This stove may be connected to a lined masonry

chimney or a listed factory built chimney suitable

for use with solid fuels and conforming to ULC629

in Canada or UL-103HT in the USA. Do not connect

it to a chimney serving another appliance. To do

so will aect the safe operation of both appliances,

and will void the stove warranty. You must comply

with the local authority having jurisdiction and/or

in Canada, CSA installation standard B365-M87.

The chimney connector must be 6" diameter, 24 MSG

Black/Blue steel. Do not use aluminum or galvanized

steel, they cannot properly withstand the extreme

temperatures of a wood re. The chimney connector

between the stove and the chimney should be as

short and direct as possible.

The chimney connector must be attached to either

an approved masonry chimney or one of the listed

factory built chimneys suitable for use with solid

wood fuel. All joints must be tight and fastened

with sheet metal screws.

WARNING

THE CHIMNEY CONNECTOR IS TO

BE USED ONLY WITHIN THE ROOM,

BETWEEN THE STOVE AND CEILING/

WALL. NEVER USE A CHIMNEY

CONNECTOR TO PASS THROUGH

AN ATTIC OR ROOF SPACE, CLOSET

OR SIMILAR CONCEALED SPACE,

OR A FLOOR, OR CEILING. AN

EFFECTIVE VAPOR BARRIER

MUST BE MAINTAINED AT THE

LOCATION WHERE THE CHIMNEY

OR COMPONENT PENETRATES TO

THE EXTERIOR OF THE STRUCTURE.

ALWAYS MAINTAIN THE MINIMUM

CLEARANCES TO COMBUSTIBLES

AS REQUIRED BY THE APPLICABLE

BUILDING CODES.

when using single

wall pipe

Minimum

18"

(457mm)

centerline

8 | F1150 Wood Stove

FACTORY

BUILT CHIMNEY

When a metal prefabricated chimney is used, the manufacturer's installation instructions must be followed. You must also purchase and install the

ceiling support package or wall pass-through and "T" section package, restops (where needed), insulation shield, roof ashing, chimney cap, etc.

Maintain proper clearance to the structure as recommended by the manufacturer. The chimney must be the required height above the roof or other

obstructions for safety and proper draft operation. The space heater is to be connected to a factory-built chimney conforming to CAN/ULC-S629,

Standard for 6500C Factory-Built Chimneys.

MASONRY

CHIMNEY

Ensure that a masonry chimney meets the

minimum standards of the National Fire

Protection Association (NFPA) by having it

inspected by a professional. Make sure there

are no cracks, loose mortar or other signs of

deterioration and blockage. Have the chimney

cleaned before the stove is installed and

operated. When connecting the stove through a

combustible wall to a masonry chimney, special

methods are needed.

Ensure that an eective vapour barrier at the

location where the chimney or other component

penetrates to the exterior of the structure.

MASONRY

FIREPLACE

There are listed kits available to connect a stove

to a masonry replace. The kit is an adaptor

that is installed at the location of the replace

damper. The existing damper may have to be

removed to allow installation.

Ensure that an eective vapour barrier at the

location where the chimney or other component

penetrates to the exterior of the structure.

This unit is designed to use either a 5.5" (140mm)

or 6" (152mm) ue liner only in the connes of

the masonry chimney as shown.

Minimum 18" (457mm)

to centerline

Minimum

18"

(457mm)

centerline

When referencing installation or connection

to masonry replaces or chimneys, the

masonry construction must or shall be code

complying.

When referencing installation or connection

to masonry replaces or chimneys, the

masonry construction must or shall be code

complying.

This unit is designed to use either a 5.5"

(140mm) or 6" (152mm) ue liner only in

the connes of the masonry chimney.

This unit is designed to use either a 5.5"

(140mm) or 6" (152mm) ue liner only in

the connes of the masonry chimney.

F1150 Wood Stove | 9

Method A: 12" (304.8 mm) Clearance to Combustible Wall Member:

Using a minimum thickness 3.5" (89 mm) brick and a 5/8" (15.9 mm)

minimum wall thickness clay liner, construct a wall pass-through. The

clay liner must conform to ASTM C315 (Standard Specication for

Clay Fire Linings) or its equivalent. Keep a minimum of 12" (304.8

mm) of brick masonry between the clay liner and wall combustibles.

The clay liner shall run from the brick masonry outer surface to the

inner surface of the chimney ue liner but not past the inner surface.

Firmly grout or cement the clay liner in place to the chimney ue liner.

Method B: 9" (228.6 mm) Clearance to Combustible Wall Member:

Using a 6" (152.4 mm) inside diameter, listed, factory-built Solid-Pak

chimney section with insulation of 1" (25.4 mm) or more, build a wall

pass-through with a minimum 9" (228.6 mm) air space between the

outer wall of the chimney length and wall combustibles. Use sheet

metal supports fastened securely to wall surfaces on all sides, to

maintain the 9" (228.6 mm) air space. When fastening supports to

chimney length, do not penetrate the chimney liner (the inside wall

of the Solid-Pak chimney). The inner end of the Solid-Pak chimney

section shall be ush with the inside of the masonry chimney ue, and

sealed with a non-water soluble refractory cement. Use this cement

to also seal to the brick masonry penetration.

Minimum

12 in. (304.8mm)

to combustibles

Masonry chimney

Chimney Flue

Minimum chimney clearance to brick

and combustibles 2 in. (50.8mm)

Minimum clearance

12 in. (304.8mm)

of brick

Chimney

connector

Fire clay

liner

Method C: 6" (152.4 mm) Clearance to Combustible Wall Member:

Starting with a minimum 24 gage (.024" [.61 mm]) 6" (152.4 mm)

metal chimney connector, and a minimum 24 gage ventilated wall

thimble which has two air channels of 1" (25.4 mm) each, construct a

wall pass-through. There shall be a minimum 6" (152.4 mm) separation

area containing berglass insulation, from the outer surface of the wall

thimble to wall combustibles. Support the wall thimble, and cover its

opening with a 24-gage minimum sheet metal support. Maintain the

6" (152.4 mm) space. There should also be a support sized to t and

hold the metal chimney connector. See that the supports are fastened

securely to wall surfaces on all sides. Make sure fasteners used to

secure the metal chimney connector do not penetrate chimney ue liner.

Method D: 2" (50.8 mm) Clearance to Combustible Wall Member:

Start with a solid-pak listed factory built chimney section at least

12" (304 mm) long, with insulation of 1" (25.4 mm) or more, and an

inside diameter of 6" (2 inches [51 mm] larger than the 6" [152.4

mm] chimney connector). Use this as a pass-through for a minimum

24-gage single wall steel chimney connector. Keep solid-pak section

concentric with and spaced 1" (25.4 mm) o the chimney connector

by way of sheet metal support plates at both ends of chimney section.

Cover opening with and support chimney section on both sides with

24 gage minimum sheet metal supports. See that the supports are

fastened securely to wall surfaces on all sides. Make sure fasteners

used to secure the metal chimney connector do not penetrate chimney

ue liner.

COMBUSTIBLE WALL CHIMNEY CONNECTOR PASS-THROUGHS

10 | F1150 Wood Stove

RECOMMENDED HEIGHTS FOR WOODSTOVE FLUE

Simple rules on draft. See Table 1.

1) At sea level minimum height is 12' straight.

2) Add the following vertical height to compensate for:

45 deg. elbow = 1 ft.

90 deg. elbow = 2 ft.

"T" = 3 ft.

Each foot of horizontal run = 2 ft.

3) Add 4% overall for each 1000' above sea level.

Example: a)

1-1/2 ft. of horizontal run = 3 ft.

one "T" = 3 ft.

Total Addition (at sea level) = 6 ft.

Example: b)

One 90 deg. elbow = 2 ft.

2 ft. of horizontal run = 4 ft.

one "T" = 3 ft.

Total Addition (at sea level) = 9 ft.

Recommended Flue Height

Elevation Example a) Example b)

0' 18' 21'

1000' 18.72' 21.84'

2000' 19.44' 22.68'

5000' 21.60' 25.20'

8000' 23.76' 27.72'

TABLE 1

MINIMUM RECOMMENDED FLUE HEIGHTS IN FEET

(Measured from the top of the unit)

# OF ELBOWS

ELEVATION (FT)

ABOVE SEA LEVEL 0 2 x 15o4 x 15o2 x 30o4 x 30o2 x 45o4 x 45o

0-1000 12.0 13.0 14.0 15.0 18.0 16.0 20.0

1000-2000 12.5 13.5 14.5 15.5 19.0 16.5 21.0

2000-3000 13.0 14.0 15.0 16.0 19.5 17.0 21.5

3000-4000 13.5 14.5 15.5 17.0 20.0 18.0 22.5

4000-5000 14.0 15.0 16.0 17.5 21.0 18.5 23.0

5000-6000 14.5 15.5 17.0 18.0 21.5 19.0 24.0

6000-7000 15.0 16.0 17.5 18.5 22.5 20.0 25.0

7000-8000 15.5 16.5 18.0 19.0 23.0 20.5 25.5

8000-9000 16.0 17.0 18.5 20.0 24.0 21.0 26.5

9000-10000 16.5 17.5 19.0 20.5 24.5 22.0 27.0

NOTE: No more than two osets (four elbows) allowed.Two 45oelbows equal one 90oelbow.

WARNING:

DO NOT INSTALL IN SLEEPING

ROOM

CAUTION: The structural integrity of the mobile home

oor, wall and ceiling/roof must be maintained.

Draft is the force which moves air from

the appliance up through the chimney.

The amount of draft in your chimney

depends on the length of the chimney,

local geography, nearby obstructions and

other factors. Too much draft may cause

excessive temperatures in the appliance

and may cause damage. An uncontrollable

burn or excessive temperature indicates

excessive draft. Inadequate draft may

cause back pung into the room and

plugging of the chimney. Inadequate

draft will cause the appliance to leak

smoke into the room through appliance

and chimney connector joints. Ensure

the heater is installed in areas that are

not too close to neighbors or in valleys

that would cause unhealthy air quality

or nuisance conditions.

Table of contents

Other Regency Indoor Fireplace manuals

Regency

Regency Bellavista B41XT-NG1 Quick start guide

Regency

Regency U41 Quick start guide

Regency

Regency GEM54-NG Quick start guide

Regency

Regency GF900C-NG1 Quick start guide

Regency

Regency F250B Quick start guide

Regency

Regency Ultimate U1500E-LP User manual

Regency

Regency Contura RC500E Quick start guide

Regency

Regency FPI FP90 Quick start guide

Regency

Regency Panorama P33E-NG11 User manual

Regency

Regency Liberty Gas Fireplace L676-NG1 Quick start guide

Regency

Regency L676S-LP1 Sunrise User manual

Regency

Regency GFi750NG Quick start guide

Regency

Regency Classic I1200S Quick start guide

Regency

Regency Horizon HZ54-NG Quick start guide

Regency

Regency E18-NG Quick start guide

Regency

Regency Energy U32-NG10 Quick start guide

Regency

Regency P33E-NG4 Quick start guide

Regency

Regency I100B-1 BERWICK Quick start guide

Regency

Regency P33-5 Quick start guide

Regency

Regency City Series Quick start guide

Regency

Regency P33CE-NG10 Quick start guide

Regency

Regency IG34-LPG Quick start guide

Regency

Regency B36XT-NG User manual

Regency

Regency Greenfire GF900L Quick start guide

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual