OPERATION MANUAL
P/N 95-0400
Literature P/N 01-0183
This procedure will locate leaks in vacuum lines as well as manifolds,
EGR valves, oil seals, gaskets, solenoids, o-rings, ducting, throttle
shafts, diaphragms, canisters, and more
For best results, test in a draft-free area
1. Remove the air filter housing from ducting
2. If the vehicle has a round inlet tube from the air filter, place the
Cone Adapter into the duct toward the engine
3. Put Vapor Supply Hose into Cone Adapter to introduce vapor into
the system
4. Use provided Halogen Inspection Light to locate leaks
ALTERNATIVE METHOD
1. Select an appropriate vacuum line to access the vacuum system
(i.e. a brake booster supply line before the check valve)
2. Seal all system openings
• Air Intake must be sealed to prevent vapor from leaking back
through the intake
• To seal the intake, use Cap Plugs, a latex glove, or plastic wrap
around the filter
3. Put Vapor Output Hose into Cone Adapter to introduce vapor into the
system. Use provided Halogen Inspection Light to locate leaks.
This test is most effective when exhaust system is cold thermal
expansion may cause small leaks to seal
1. Insert appropriate Cone Adapter into the end of the tailpipe. If the
vehicle has dual exhaust with cross over system, plug the other
tailpipe to seal the system
2. Put Vapor Output Hose into Cone Adapter to introduce vapor into
the system
A hot catalytic converter may consume some of the vapor
All testing is performed with the engine off
DRAIN VAPOR HOSE
Elevate the machine
Allow the entire vapor hose to hang downward
Place a container beneath the nozzle to capture fluid
Process takes approximately 5 minutes
PROBLEM SOLUTION
No Green Light Check polarity
Ensure 12-Volt battery is fully-charged
Reconnect power cables
Red Light Flashing / Ensure 12-Volt battery is fully-charged
No Red Light Open circuit / internal component
Contact Redline Detection Technical Support
No Air Flow Check connection to compressed air
Open the flow control valve
Check hoses are not kinked
Not Enough Vapor Check Fluid Level
Open the flow control valve
Check hoses are not kinked
Gauge Bouncing Drain Vapor Hose
Flow Meter Bouncing
REDLINE TECHNICAL SUPPORT
RedlineDetection.com/support
+1 714-451-1411
Monday - Friday: 7:00 to 17:00 PACIFIC TIME
Stay Connected
Facebook.com/RedlineDetection and Twitter @RedlineDetect
The manufacturer, Redline Detection, LLC. (“Redline”) warrants this product to
be free from defects in workmanship and material under normal use and service.
This limited warranty is extended to the original end-user purchaser and is valid
for one year from date of manufacture. Redline’s liability under this warranty is
limited to:
(1) Repair or replacement of any parts or product which are determined to be
defective; or at Redline’s sole option
(2) Refund of the purchase price. In either event, product to be returned shipping
prepaid within the one year warranty period. Products are only to be used by
persons having skill and knowledge in the automotive repair field, and improper
use or maintenance may cause serious injury. In no event shall Redline be liable
beyond replacement of product or refund of the purchase price. This warranty
shall void if a product is improperly maintained, altered, abused or otherwise
misused in any way.
The limited warranty does not cover defects or malfunction caused by misuse,
abuse, or failure to follow operating instructions. It doesn’t cover cosmetic
or incidental damages or machines that have fully or partially disassembled.
Also, the warranty will not apply to damage caused by unauthorized alteration,
modification or repair of the product.
THE AFORESAID WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, AND THERE
ARE NO OTHER WARRANTIES OR REPRESENTATIONS OF ANY KIND WHATSOEVER
MADE BY REDLINE, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT
LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR USE OR APPLICATION.
THE PURCHASER’S SOLE REMEDY FOR ANY DEFECTIVE PRODUCT SHALL BE
REPAIR, REPLACEMENT OR REFUND AS STATED ABOVE AND REDLINE SHALL
NOT BE LIABLE TO ANYONE FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL,
INDIRECT OR PUNITIVE DAMAGES ON ACCOUNT OF DEFECTIVE PRODUCTS,
HOWEVER CAUSED, UNDER ANY THEORY OF LIABILITY.
HOW TO DIAGNOSE INTAKE SYSTEM & VACUUM LEAKS SPECIFICATIONS TROUBLESHOOTING WARRANTY
HOW TO DIAGNOSE EXHAUST LEAKS MAINTENANCE
I
N
C
H
E
S
O
F
W
A
T
E
R
V
A
C
U
U
M
P
R
E
S
S
U
R
E
I
N
C
H
E
S
O
F
W
A
T
E
R
1PSI
7
0
-10
-20
+30
+20
-7 kPa
-5
-3
-1 +1
3
5
-30
LEAK SIZE
THOUSANDTHS
L/Min
1.5+
mm 6
1.5+
mm 6
1.5+
mm 6
1.5+
mm 6
1.5+
mm 6
1.5+
mm 6
EVAP
LEAK
SIZE
+-
Power Supply 12 Volts DC
Power Consumption 12 amps
Output Pressure 0.5 PSI / 13.0 in. H20 / 0.032 BAR
Operating Temperature 0°F to 140°F (-17°C to 60°C)
Operating Modes Vapor Cycle / Air Only Cycle
Pressure Supply Compressed Air
Housing Material Steel
Dimensions 6” (15 cm) x 7” (18 cm) x 7” (18 cm)
Machine Weight 7.6 lbs (3.45 kgs)
Shipping Weight 13.85 lbs (6.28 kgs)
Limited Warranty 1 Year
!
