Ranger Products RX3040 Technical manual

QUICK START SETUP GUIDE- Demounting

1. The Centering Cone must make contact with the Hub

Hole Edge.

2. You MUST use the Turntable Spacer when the Hub

Hole of the Rim requires use of either of the Large Cen-

tering Cones.

3. Use of the Large Centering Cone without the Spacer

will prevent proper wheel mounting.

Setting the Bead Breaker Roller

and “Target Lock” Distance.

1. Set the distance from the Rim edge to the Bead

Breaker Roller to 1/8’.

2. Once this distance is set. DO NOT move the

Turntable. When you press the “Target Lock” Button for

the Bead Hook / Tab Arm, the Hook/Tab Arm will extend

and stop the same distance from the Rim that was set

with the Bead Breaker Roller.

3. ALWAYS liberally lube both Upper and Lower Beads,

then Hook Upper Bead as Shown.

REFER TO THE COMPLETE SAFETY, INSTALLATION AND OPERATION MANUAL IF YOU ARE UNSURE OF ANY

TIRE MOUNTING OR DEMOUNTING PROCEDURES OR HAVE NOT USED THIS STYLE OF TIRE CHANGER.

IMPORTANT! FOLLOW THIS SET UP GUIDE PRIOR

TO USING THE MACHINE OR DAMAGE TO THE

TIRE CHANGER OR RIM & TIRE MAY OCCUR!

Both the Upper and Lower Bead Breaker Rollers can

articulate while breaking the tire bead by applying pres-

sure closer to the Rim Edge.

Only the Lower Bead Breaker Roller can be locked

when using the Lower Bead Breaker Roller to help lift the

lower bead over the upper rim edge. Pushing the

Locking Pin locks the Lower Roller. Pulling the Locking

Pin out allows the Lower Roller to articulate.

Locking / Unlocking the

Lower Bead Breaker Roller

1. When using the Lower Bead Breaker Roller to Break

the Lower Bead, unlock the Roller, by pulling the Locking

Pin out. The Lower Roller will articulate and push directly

on the lower bead to break the Lower Bead.

2. When using the Lower Bead Breaker Roller to push

the Lower Bead up off the Upper Rim, lock the Roller by

pushing the Lock Pin in.

3. Locking the Lower Bead Breaker Roller will prevent

the Roller from articulating and hitting /damaging the Rim

or Roller.

NOTE:

The Tool Head may need to be extended beyond the

“Target Lock” position during demounting of some

tire/rim combos. In that extended position, use caution

be very aware of where the Tool Head is in relation to the

rim. The rim or tire can be damaged if care is not taken in

knowing where the tool head is at all time.

Use the Video assist feature and direct viewing to

verify the Tool Head’s location before initiating

movement of the Tool Head

PRACTICE, PRACTICE, PRACTICE!

Time spent practicing on inexpensive steel wheel/ tire

combos before beginning work on a valuable rim or tire,

will prevent costly damage. Take the time to get used

to the controls and operation of the machine BEFORE

working on customers valuable rims and tires.

BendPak / Ranger, 1645 Lemonwood Dr., Santa Paula, CA. 93060 Tel: 1-805-933-9970 Fax: 1-805-933-9160

REFER TO THE COMPLETE SAFETY, INSTALLATION AND OPERATION MANUAL IF YOU ARE UNSURE OF ANY

TIRE MOUNTING OR DEMOUNTING PROCEDURES OR HAVE NOT USED THIS STYLE OF TIRE CHANGER.

QUICK START SETUP GUIDE - Demounting

REV A 10-19-10

LOWER BEAD

1. ALWAYS liberally lube both Upper and Lower Beads,

during mounting procedures, then position the Tool Head

with the Tab Side down

2. Lower Tool Head until lower bead is below the rim.

If necessary use the Assist Roller to help push the lower

bead is below rim edge.

3. Rotate Turntable and lower the Tool Head until the

tire’s lower bead drops below top edge of Rim.

UPPER BEAD

1. ALWAYS liberally lube both Upper and Lower Beads,

during mounting procedures, then position the Tool Head

with the Tab Side down.

2. Lower Tool Head till upper bead is pushed below rim.

Use the Assist Roller and Drop Center Tool to help push

the bead is below rim edge.

3. Position the Drop Center Tool as shown to keep the

Bead in the rims’s drop center.

4. Rotate Turntable and lower the Tool Head until entire

Bead drops below top edge of Rim.

REFER TO THE COMPLETE SAFETY, INSTALLATION AND OPERATION MANUAL IF YOU ARE UNSURE OF ANY

TIRE MOUNTING OR DEMOUNTING PROCEDURES OR HAVE NOT USED THIS STYLE OF TIRE CHANGER.

IMPORTANT! FOLLOW THIS SET UP GUIDE PRIOR

TO USING THE MACHINE OR DAMAGE TO THE

TIRE CHANGER OR RIM & TIRE MAY OCCUR!

QUICK START SETUP GUIDE- Mounting

BendPak / Ranger, 1645 Lemonwood Dr., Santa Paula, CA. 93060 Tel: 1-805-933-9970 Fax: 1-805-933-9160

REFER TO THE COMPLETE SAFETY, INSTALLATION AND OPERATION MANUAL IF YOU ARE UNSURE OF ANY

TIRE MOUNTING OR DEMOUNTING PROCEDURES OR HAVE NOT USED THIS STYLE OF TIRE CHANGER.

ITEM DESCRIPTION Part Number

1 Plastic Bead Breaker Roller; 150 x26mm; RX3040 5327127

2 Assist Arm Roller; RX3040 5327019

3 Reversible Drop Center Tool Head; RX3040 5327010

4 Tire Restraining Pin; RX3040 5327004

5 Nylon Tire Restraining Pin Cover; RX3040 5327003

6 Tab Plastic Insert; Demount Head; RX3040 (Available in Kit Only*) -----------

7 Plastic Demount Head Hook; RX3040 5327008

8 Plastic Demount Head Tab; RX3040 5327007

9 Hook Plastic Insert; Demount Head; RX3040 (Available in Kit Only*) -----------

* Demount Tool Insert Kit; RX3040 5327085

(5ea)Tab Plastic Insert; Demount Head; RX3040 Item #7

(5ea) Hook Plastic Insert; Demount Head; RX3040 Item #9

During operation of the RX3040 you will likely damage some of the components listed below. We supply

spares with your Tire Changer, but you will always want to have some on hand and when training new operators.

The inserts, pins and hooks are designed to break before damage is done to a rim or tire. Use a inexpensive

steel rim and tire combo for training.

QUICK START SETUP GUIDE- Mounting

REV A 10-19-10

Other manuals for RX3040

Other Ranger Products Tyre Changer manuals

Ranger Products

Ranger Products R26EX User manual

Ranger Products

Ranger Products R980AT User manual

Ranger Products

Ranger Products RX3040 User manual

Ranger Products

Ranger Products R710 User manual

Ranger Products

Ranger Products R26AT User manual

Ranger Products

Ranger Products R23 User manual

Ranger Products

Ranger Products R715 User manual

Ranger Products

Ranger Products R30XLT User manual

Ranger Products

Ranger Products R980X User manual

Ranger Products

Ranger Products R23LT User manual

Popular Tyre Changer manuals by other brands

MW TOOLS

MW TOOLS BT200 manual

Hunter

Hunter Maverick Series Operation instructions

Corghi

Corghi BR2-C1E Operator's manual

Snap-On

Snap-On EEWH311B Operation instructions

TMG

TMG LC889NV user manual

JMP

JMP Fix Moto Translation of original operating instructions

GIULIANO

GIULIANO S224 Installation, operation and maintenance guide

Corghi

Corghi A 9222 HP TI Operator's manual

foc.us

foc.us F640 user guide

Corghi

Corghi Artiglio Master 26 MI Operator's manual

SICE

SICE S 52A instruction manual

Sealey

Sealey TC968.V2 quick start guide

Coats

Coats 80C operating instructions

HENNESSY INDUSTRIES

HENNESSY INDUSTRIES Coats Rim Clamp X-Model Series instructions

Draper

Draper 78612 user manual

Aston Global

Aston Global ATC-5800 Installation, Operation and Maintenance User’s Manual

HENNESSY INDUSTRIES

HENNESSY INDUSTRIES Coats CHD-4730-4730W Operating and maintenance instructions

Butler

Butler NAV11N instruction manual