Quadient IS-6000 User manual

Installation Guide

IS-6000

Postage meter

Safety Requirements1.

Please read this section carefully before connecting or using your equipment.

Power Connection

Before powering up your Franking System, please check to ensure the system meets your

local AC voltage requirements. For information on power specifications, please refer to the

plates at the back of each System component.

In addition to checking the power requirements, we also recommend that you:

•Use an outlet that is easily accessible.

•Do not route the power cord between pieces of furniture or over sharp edges.

•Avoid using outlets controlled by wall switches or shared by other equipment.

•Make sure there is no strain on the power supply cord.

THIS EQUIPMENT MUST BE GROUNDED

•Only connect the power plug to an outlet provided with a

protective ground contact.

•To reduce the risk of fire, use only the power cord supplied

with the franking system.

•Do not use ground adaptors.

•Do not use this product on a wet floor or near water.

•In case of liquid spillage, disconnect the power cord from the

outlet and proceed to cleaning.

To reduce the risk of fire, only connect the modem to the telephone

lineusingsuppliedcable(seeSystemSpecificationsonpage321).

| Page 6 | aug-05-2014 10:23 |

Compliance

Energy Star® Compliance

Office equipment is generally powered on 24 hours a day, so power management features

are important for saving energy and reducing air pollution.

Your Postage Meter is an Energy Star® qualified Postage Meter that automatically goes

into a low-power 'Sleep' mode after a period of inactivity.

Spending a large portion of time in low-power mode not only saves energy but helps your

equipment run cooler and last longer.

Environmental compliance

A program is implemented for the recycling of worn Postage Meter at the end of their

lifetime. Contribute in a responsible way to the environmental protection by consulting your

retailer internet site, or by contacting him. He will inform you of the collection and treatment

processes of these machines.

CE compliance

Products presented in this guide conform to requirements of directives number 2006/95/CE

and 2004/108/CE.

This is a class A product. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user

will be required to correct the interference at his own expense.

| Page 7 | aug-05-2014 10:23 |

How to Turn the System ON/OFF

1. Press either side of the switch to turn the Postage Meter ON or OFF.

- The dash (or I) indicates the ON side.

- The circle (or O) indicates the OFF side.

After switching the system OFF, there may be a delay of up to 20

seconds to park the print head and free the remaining voltage.

System Sleep Mode

Your Postage Meter is Energy Star® qualified and automatically goes into a low-power

'Sleep' mode after a period of inactivity.

A very low-power 'Sleep' mode, called 'Soft-off' is also available.

•The Postage Meter will automatically switch to 'Sleep' mode after 2 minutes of

non-activity. The Supervisor can change this 2-minute default setting.

•The Postage Meter can be set to 'Sleep' mode manually by a short press on the

Sleep/Wake button.

•The Postage Meter can be set to 'Soft-off' mode manually by a long press on the

Sleep/Wake button.

The light located on the display indicates:

- Amber (continuous): the Postage Meter is in Sleep mode (low power mode).

- Amber (blinking): the Postage Meter is in Soft-off mode (very low power mode).

- Green: the Postage Meter is in Wake up mode and ready for use.

SLEEP / WAKE KEY

The Sleep/Wake key is located at the top right corner

of the control panel.

Wakes the Postage Meter up or turns it to 'Sleep' or

'Soft-off' mode.

Sleep/wake

| Page 31 | aug-05-2014 10:23 |

How to Switch Between 'Sleep' And 'Wake' Modes

1. Press the Sleep/Wake key to switch between “Sleep” and “Wake” modes.

To avoid weighing errors, make sure the Weighing Platform is clear

when you Wake up the machine.

Mail processing Start/Stop

To process mail, use the following keys.

START / STOP KEYS

Red button – Stops mail processing.

Stop

Green button – Starts mail processing.

Start

| Page 32 | aug-05-2014 10:23 |

2.GeneralSpecifications

Base

•Dimensions(cm) (Width x Length x Height): 64 x 22 x 34

•Weight: 21kg

•Power supply: 230 V (+/- 10 %) 3 prong

•Frequency: 50Hz

•Maximum Input Power: 294W

•Ambient Temperature:+10°Cto40°C

Relative Humidity: 20 % to 80 % relative humidity (without condensation).

Feeder

•Dimensions(cm) (Width x Length x Height): 46 x 80 x 35

•Weight:29kg

•Power supply: 120 V (+/- 10 %) 3 prong

•Frequency:50Hz

•Maximum Current Rating :5A

•Ambient Temperature: +10 °C to 40°C

•Relative Humidity: 20 % to 80 % relative humidity (without condensation).

Dynamic Weighing Module

•Dimensions(cm) (Width x Length x Height): 64.2 x 48.5 x 28

•Weight:17kg

•Power supply: 120 V (+/- 10 %) 3 prong

•Frequency:50Hz

•Maximum Input Power:71W

•Ambient Temperature:+10°Cto40°C

•Relative Humidity: 20 % to 80 % relative humidity (without condensation).

| Page 323 | | aug-05-2014 10:23 |

.SystemConnections

Base + Feeder

CAN

Power

| Page 324 | aug-05-2014 10:23 |

Base + Feeder + Dynamic Weighing Module

CAN

Power

| Page 325 | aug-05-2014 10:23 |

Base + Stacker

Power

| Page 326 | aug-05-2014 10:23 |

.SystemConnectors

Base connectors

On the left-hand side

The ON/OFF switch is located at the rear of the right

hand side of the Postage Meter base.

ON/OFF switch

To wall socket

Power connector

To Conveyor Stacker

Power connector

For future use

RJ 45

To any USB device*

USB ports

USB devices : Keyboard, Printer, Modem, LAN adaptor, Bar Code Reader…

All USB devices have to be plugged with the system powered OFF.

| Page 327 | | aug-05-2014 10:23 |

Other manuals for IS-6000

Table of contents

quadient IS-6000 User manual

Popular Postal Equipment manuals by other brands