Qomo QPen User manual
Multi-function Wireless Interactive Pen
QPen User Manual
Best for your presentation
Information in this manual is subject to change without notice.
Introduction
First thank you for purchasing QOMO product: Multi-function Wireless Interactive Pen.
QOMO Multi-function Wireless Interactive Pen is designed to give you unparalleled
presentation experience. QPen is short for Multi-function Wireless Interactive Pen.
With your QPen in hand, the intelligent pen tray is really at your fingertips! The QPen
eloquently utilizes the Flow!Works Pro Software for one-click function control including
color selection, eraser change, page turnover as well as PowerPoint operation. Also, QPen
buttons can be customized to be any of your favorite and most-frequently used functions.
Built-in magnets enable you to freely “place” QPen on any metallic surface of the
whiteboard/screen and quickly “pick it up” whenever you get ready to use it.
Extremely user-friendly design allows wireless charging for QPen by simply putting it into
the QOMO intelligent pen tray slot.
Attentions
Use 1* AAA rechargeable battery for the QPen.
Remove the battery if the QPen won’t be used for long time.
Do not drop or strike the QPen to avoid internal PCB board damage.
Be careful not to spill water or other liquids onto the QPen.
Keep the product dry and do not clean this product with chemicals, detergents or water.
Pay attention to the polarity of the battery when installing the battery.
Keep distance within 10 meters when using the QPen.
Ensure that you use the QPen with Flow!Works Pro software.
Do not disassemble it to perform any repair. In case of damage please contact technical
support.
QPen Setup
1. Take the dongle cover off from the QPen back side.
2. Take out the dongle, and plug into the connecting device interface. Then check if the
dongle is well connected with the device.
3. Use the screwdriver to pull out the back side battery-cover screw and take off the battery
cover.
4. Put the 1*AAA rechargeable battery into the battery slot.
5. After battery is in place, try to click the QPen buttons to see if the functions can work. Put
on battery cover and slightly tighten the screw.
6. Place the dongle cover on to finish the set up.
Functions Instructions
Interact with Flow!Works Pro Software
The four buttons on QPen serve as Flow!Works Pro shortcuts with default functions like color
change, eraser change and page turnover. Also interacted with Flow!Works Pro, these buttons
can be customized to be your favorite and most-frequently used functions.
Default buttons
setting
Eraser button
1. Click to erase ink.
2. Hold to erase objects.
3. Release after holding to switch back to
pen function.
Page turnover
button
1. Page up and down in remote distance.
2. Hold to enter/exit slide show.
Color selection
button
1. Click to change pen’s ink colors.
2. Hold to erase ink.
3. Release after holding to switch back to
pen function.
Customize QPen functional buttons to interact with Flow!Works Pro:
1. Click Flow!Works Pro server icon and QPen software, a setting window appears.
QPen A setting interface
QPen B setting interface
2. Click button, select relevant function from the dropdown list on the right option box.
3. Click Ok or Apply to finish setting. Slide left to disable a button function.
The software supports 7 colors switching for QPen. Click this icon to select and add new
colors; Click minus icon on the top-left to delete the corresponding color.
Note: QPen B setting is the same as QPen A.
Interact with PowerPoint
QPen can interact with PowerPoint like starting/ending slide show, page turnover, annotating
over the slide etc.
Default buttons
setting
Erasers
1. Click to erase;
Page turnover
1.Click to go to previous/next slide.
2. Hold to enter/exit slide show.
Color selection
1. Click to change pen’s ink colors.
Customize QPen functional buttons to interact with PowerPoint:
1. Click Flow!Works Pro server icon and QPen Microsoft PowerPoint, a setting
window appears.
QPen A setting interface
2. Click button, select relevant function from the dropdown list on the right option
box.
3. Click OK or Apply to finish setting. Slide left to disable a button function.
The software supports 7 colors switching for QPen. Click this icon to select and add
new colors; Click minus icon on the top-left to delete the corresponding color.
Note: QPen B setting is the same as QPen A.
Specifications
Model
QPen
Material
ABS
USB Interface
USB-A
Default Functions
(Interact with Flow!Works Pro)
Colors change, page turnover, eraser
Default Functions
(Interact with PowerPoint)
Enter key function, browse all slides,
go to previous/next slide, start/end slide show,
change pen colors, erase
Default Ink Colors
Black, red, green, blue
Working Voltage
1.5V （AAA battery）
Standby Current
0.1mA
Working Current
<34mA
Maximum Power
50mW
RF Transmit Power
-40~8dbm
RF Received Power
-97dbm@250K/-92dbm@1M/-89dbm@2M
Communication Mode
Wireless 2.4G+USB2.0 receiver
Communication Distance
10m
RF Transmission Rate
250Kbps/1Mbps/2Mbps
Working Frequency
2.40 GHz~2.48 GHz
Working Temperature
0℃~+40℃
Storage Temperature
-40℃~+80℃
Dimensions
Pen:152mm*20mm
Receiver: 19mm*14.6mm*6mm
Table of contents
