Qlight S80AR User manual
S80AR / S80AU
Thank you for purchasing Q.Light product. Please read this
manual carefully before installing this product for safe and long
use.
▪Having a high revolving durability by using a small bearing on
the axis of rotation.
▪Signal light diffusing effectiveness is high with using a vacuum
coated reflector.
▪Buzzer volume(option): Max 90dB/m
▪
RPM : 120~140 (control freely)
▪Material : Lens-AS, Body-ABS, Reflector-thermostable ABS
▪Protection Class : IP44
▪
General Specification
Model
Voltage
Current
Bulb
Weight
Color
S80AR
S80AU
DC12V
0.484A
12V5W
T16x35 15S
5
0.34Kg
RED-R
AMBER
-A
GREEN
-G
BLUE-
B
DC24V
0.310A
24V5W
T16x35 15S
6
0.34Kg
AC110V
0.080A
12V5W
T16x35 15S
5
0.52Kg
AC220V
0.040A
12V5W
T16x35 15S
5
0.52Kg
▪External View Drawing
1) S80AR
S80AR
2) S80AU
S80AU
This item can connect power lines to the plate element located
at the bottom board of this item. Please read carefully this
instruction to wire.
1).Separating the bottom board and the body
Releasing the bolts(M4-1EA)④which connected the bottom
board. and separate the bottom board①and the body②then
check inside.
2).Connecting power lines
Please connect power lines refer to the upper product structure.
Releasing the bolts(M4-2EA)⑤attached on the plate element③
and connecting O type terminal or Y type terminal linked with the
power lines outside.
▪In case of product using AC voltage, connect the line without
Polarity(wire color).
▪In case of product using DC voltage, black line is negative(-).
OPERATING MANUAL
Bulb Revolving Warning Light
Product Structure
Wiring Instruction
※After finishing the power lines connection and attached the
product well, the electric power supplies by the plate element⑦
on the body②.
Indoor Outdoor
▪This product was manufactured with the structure for indoor use.
Installing in any direction is okay for indoor use.
▪Outdoor use is limited at a place where no water or very little
water percolates. Mounting also should be done only on the
vertical standing direction.
▪Mount at the place where exists low vibration, low impact, low
moisture and low dust as long as possible.
▪Please make a hole by a drill where you need to attach our
product and refer to below picture for a hole size. (Make sure
PCD from external view drawing.)
▪Please connect power lines refer to the upper wiring instruction.
▪Attach the bottom board①where you need to attach.
▪Make the product body drape over the bottom board part⑥
then push the product body into the bottom board.
▪Fix the product bottom board by using bolts④.
1) Warning!
Must turn off power supply and change bulb after 1 minute at
least.
2) Lens Removal
Remove lens by turning it counterclockwise. and make sure
related parts on the assembling board.
3) Bulb Change
▪Make sure the rated voltage and wattage of new bulb. If the
voltage of new bulb is higher than original bulb, the life of
product can be reduced and can cause damage on lens and
reflector. Therefore, please use the bulb which has the same
or lower rated voltage and wattage.
▪Bulb Removal: Press slightly the bulb downward and turn it
counterclockwise for removing.
▪Bulb Fitting: Fit new bulb into the socket by pressing it
clockwise.
Bulb removal Bulb fitting
▪If using voltage is seriously higher or lower than rated voltage, it
can reduce the self-life of the product or can cause a problem
on product operating. Make sure the using voltage does not
exceed +/-5% of the rated voltage.
▪If lens or body of the product is contaminated by chemicals such
as thinner, benzene, the product can be damaged, discolored
or deformed. Please be careful.
▪Do not give strong impact to the product. It can be a reason of
wire disconnection or short circuit.
▪Do not strongly pull the wire out from the product. It can cause a
disorder.
Mounting
Change Bulb
Caution
Situation
Main reason
Solution
Non- Lighting Partly
Wire Disconnection
of Bulb
Wire Re-connection or
Bulb Change
Feeble Lighting
Low Revolving Speed
Supplying Voltage
Lower than Rated
Voltage
Making Sure Using
Voltage
Adjust wrong for the
Revolving Speed
Make Revolving
Speed higher
Short Self-Life of Bulb
Supplying Voltage
Higher than Rated
Voltage
Making Sure Using
Voltage
Bulb overheating makes
lens shape change
Using the bulb over
rated capacity change
Change the rated
capacity bulb
Defect of
transformer(AC
Voltage Type)
Non Revolving
Problem with Motor
Contact Q.Light or
Their Agent
Neither Lighting Nor
Revolving
No Power Supply
Making Sure Power
Supply
Wrong Wiring
Making Sure Wiring
Trouble shooting
Q-LIGHT CO., LTD.
http://www.qlightkr.com
E-mail : qlightkr@qlightkr.com
Overseas Marketing Team /Plant
Tel) 055-328-4082Fax)055-328-4083
178-1 Woogye-Ri, Sangdong-Myun, Kimhae-Si,
KyungNam, Korea
This manual suits for next models
1
Other Qlight Lighting Equipment manuals
Qlight
Qlight EMCL50U Series User manual
Qlight
Qlight ST45L-ETN-BZ User manual
Qlight
Qlight SH1S User manual
Qlight
Qlight QEAL1 User manual
Qlight
Qlight QT50L-USB-BZ User manual
Qlight
Qlight STDL User manual
Qlight
Qlight S80AR User manual
Qlight
Qlight S100S User manual
Qlight
Qlight S100E User manual
Qlight
Qlight SHDL User manual
Qlight
Qlight SNE-TI User manual
Qlight
Qlight S80ADR User manual
Qlight
Qlight Microlectra QTG50 User manual
Qlight
Qlight SSEL User manual
Qlight
Qlight SESA User manual
Qlight
Qlight S150R User manual
Qlight
Qlight SAOL1 User manual
Qlight
Qlight S100R User manual
Qlight
Qlight ST45ML Series User manual
Qlight
Qlight S60LR User manual
Popular Lighting Equipment manuals by other brands
Qazqa
Qazqa Suplux SL 3 Black 103062 instruction manual
Commercial Electric
Commercial Electric 54568141 Use and care guide
CREE LIGHTING
CREE LIGHTING 304 Series installation instructions
Goobay
Goobay 49867 user manual
ECOMAN ITALIA
ECOMAN ITALIA LED T8 instruction manual
Alkalite
Alkalite Krypton KT-81 user manual
