QCAMZ HD 720p User manual
// English
QCAMZ HD 720p
135° Wide Angle // Waterproof Action Cam
Introduction
Thank you for purchasing the QCAMZ HD! Record your limits with this waterproof
HD action cam!
It is highly recommended for you to read this user manual carefully in order to fully
understand how to operate the QCAMZ HD correctly.
Table of Contents
What’s in the box?
How to use
Camera Overview
Initial set up
Charging the battery
Power ON/OFF
Taking a video
Taking snapshot photos
Memory capacity chart
Playback on your computer
On a Mac
Date & time setting
Webcam setting
LED status table
Removing/Installing battery
Repairs
Technical specications
Warranty
Warning
What’s in the box? 1. QCAMZ HD with Sound Cap
2. Camcorder Mount
3. Universal Mount
4. Roll Bar Mount
5. Magic Tape
6. Adhesive Stickers 2pcs
7. Waterproof Cap
8. Rubber O-Rings 6pcs
9. Silicon Grease
10. Hand Safety Strap
11. Rechargeable Lithium-Polymer battery
12. USB Cable
13. User Manual
How to use the QCAMZ HD
1. Camcorder on Handlebar 2. Camcorder on Vented Helmets
Roll Bar Mount Camcorder Mount Magic Tape Universal Mount Camcorder Mount
Using QCAMZ HD for water sports
When using the waterproof cap remember to put some silicon
grease to the rubber O-ring from time to time, especially before
using the camera in water. Make sure to close the rear cap tightly.
Only use the camera in water with the waterproof cap!
Rubber O-Rings Silicon Grease Waterproof Cap
3. Camcorder for Non-vented Helmets
Adhesive Sticker Universal Mount Camcorder Mount
Camera Overview
1. LED
2. Power / Shutter
3. Rear cap
4. Mode switch
5. USB Port
6. Micro SD card slot
7. Battery
8. Microphone
Initial set up
1. Make sure the camera is OFF before inserting or removing the Micro SD card!
2. Unscrew the rear cap from the back of the camera ③.
3. Put your Micro SD card (max up to 32GB) into the slot with the card label facing
down (contacts up). Use your ngernail to do this. You will hear a click sound once
the Micro SD card is in place. Then screw the rear cap back on tightly.
Only use Micro SD cards Class 6 or above.
4. If no Micro SD card is inserted into the camera, the LED light on top of the ca-
mera will start ashing red and green for approx. 30 secs and then auto shut-off.
5.The Micro SD card must be blank; meaning without images from other sources
on it. If you are using a Micro SD card previously used with other cameras, please
make sure you format the Micro SD card in your computer before using it with
your QCAMZ HD. New cards can be used straight from the packaging.
Charging the battery
Unscrew the cap located at the back of the camera ③ and connect the camera
with the USB cable to your PC ⑤ or charger (optional). The LED light will light up
blue while charging and will turn itself off once the battery is fully charged.
Before the rst use charge the battery for 10 hours!
You can record apporx. up to 120 minutes with one charge.
Power on/off
Turn on the camera // Press and hold the POWER/Shutter button for approx. 3
seconds until the green LED turns on and the red LED ashes twice. The camera
will vibrate once long, indicating it is now in stand-by mode.
Turn off the camera // Press and hold the POWER/Shutter button again for
approx. 3 seconds. The red LED light will ash twice and go off. The camera will
vibrate twice, indicating it switches off.
Standby mode // If the camera is in standby mode without activity, it will auto
switch off after approx. 3 mins to conserve battery power.
Taking a video
To take a video the camera must be set to video mode. To check unscrew the cap
located at the back of the camera ③. The video/photo switch ④ must be set to the
right for the video recording standby mode, screw the cap back on tightly.
Turn on the camera. Then press the Power/shutter button ② once shortly to start
video recording.
The camera will vibrate one short time and the LED will ash red while the video is
recording. Push the Power/shutter ② again to stop the recording. The camera will
vibrate two short times and the red LED will stop ashing.
Take Snapshot Photos
Unscrew the cap from the back ③, set the video/photo switch ④ to left for the
photo standby mode, screw the cap back on tightly.
Turn on the camera. Press the shutter button ② to start taking photos.
The camera will vibrate one short time and the LED will ash red. The camera
automatically takes a photo every 3 seconds until the battery is empty or the
Micro SD card full. Press the Power/shutter button again to stop the recording.
The camera will vibrate two short times and the red LED light will stop ashing.
Memory capacity chart
Below chart will show you the possible number of photos and videos according to
memory card size. Please use only Micro SD Cards Class 6 or above!
Memory capacity chart
Mode 4GB 8GB 16GB 32GB
HD Video Recording 720P 40 min 80 min 160 min 320 min
Digital Photos 8388 16776 33552 67104
Table of contents
Other QCAMZ Action Camera manuals
