Qazqa 90500 User manual
VAP Duo WL Black Solar
MODEL: 90500
Important: Please ensure that you charge the solar lights in maxi-
mum sunlight for a period of up to 3 days (for 2200mAh Ni-MH)
before switching on the lights, in order that the lights work on a full
charge
HOW TO DETERMINE WHERE TO MOUNT YOUR SOLAR
PIR SENSOR LIGHT
The most important thing to remember for the operaon of your
SOLAR PIR SENSOR LIGHT is that it works from the power contained
in DIRECT SUNLIGHT. The more direct sunlight the solar cell receives
in a day, the longer the light will operate.
11
3 days/72h
12
5sec1min
5
9
02 4 6 8mm
H:2.5m
φ6mm
30mm
3
10
130°
6x
6x
4x30mm
6x27mm
90°
45° 45°
90°
90°
45°
45°
130° 130°
39.5mm
46
88mm
40mm
76mm
7
φ6mm
30mm
8
90°90°
180 mm
157 mm
142 mm
207 mm
166 mm
110 mm
Main Unit:
The main unit contains the 2*6*0.5W LED, moon sensor and baery
(Ni-MH Rechargeable baery, 3.6V 2200mAh). When deciding where
to mount this unit, keep in mind that the moon sensor that acves
the light has a “field of vision” of min. 8 meters (in front of the light)
and about 130º (horizontal) at 25℃ environmental temperature.
Solar Cell:
The solar cell is the power source for the SOLAR PIR SENSOR LIGHT. It
converts the sun’s energy into electricity that charges the baery
stored in main unit. This requires DIRECT SUNLIGHT falling onto the
face of solar cell for as long as possible over the course of day.
Use the three screws supplied (#4 on parts list) to mount the solar
cell unit onto a solid surface. Make sure it is anchored into the solid
surface.
You can adjust the angle of the solar cell by moving the adjustment
support to the appropriate hook on the mounng bracket. Remem-
ber, it must face as much DIRECT SUNLIGHT over the course of the
day as possible. Keep in mine shadows that may block sunlight at
some point during the day.
Now carefully route the solar cell power cord to the main unit and
plug it into the connector on the side of the unit.
FINAL ADJUSTMENT AND START-UP
Aer you successfully installed your SOLAR PIR SENSOR LIGHT, you
are almost ready for carefree operaon with a few final steps:
Inial 3-days Charge:
On the main unit there is a dial switch with 2 posions:
●OFF ● AUTO
AUTO —
Posion for normal operaon of unit.
OFF ---
1) Posion for shipping or extended periods of non-use
2) Posion for inial 3-day charge before final adjustment and first
use. (Although the unit can charge, it is not operaonal in this
mode)
For now, turn the dial switch to OFF posion. In this posion the solar
cell will charge the baery without acvang the unit. Leave the
switch in this posion for 3 sunny days to ensure that the baery has
a full charge prior to moon sensor adjustment and normal opera-
on.
OFF AUTO
2
HOW TO ADJUST THE MOTION SENSOR
Aer the inial 3-day charge, slide the switch on the main unit to
AUTO posion.
On the moon sensor there are threes adjusng knobs: TIME / LUX
1) TIME --- Duraon me: Depending on how long you wish the unit
to stay lit aer moon stops in the field of vision, the duraon
me will adjust from 10 seconds to 1 minute. Note: Once the light
has been triggered by the PIR sensor any subsequent detecon
will start the med period again from the beginning..
2) LUX – Lux control level: The Lux control module has a built-in sen-
sing device (photocell) that detects daylight and darkness.( )
posion denotes that the loading will be turned on by PIR during
day and night, ( ) posion denotes that the loading will be
turned on by PIR only at night. You can set to operate the unit at
the desired level by adjusng the LUX knob.
Note: If, in daily posion, the unit turns on when it is too light out-
side, turn the control towards ( ). however, if the light is not acva-
ng during nighme because of a street light or bright house light,
turn this control towards ( ).
Walking-test:
Point the moon sensor to face the area you want to detect moon
in and set the TIME knob to minimum (-) posion and LUX knob to
“light” ( ) posion. Walking slowly within its detecon area, the
sensor can detects moving invisible infra-red radiaon given off by a
human body and then turn on the light. Test the coverage of the area
by walking slowly around unl not to switch on the light.
ADJUSTMENT OF THE LAMP HOUSING:
Point the lamp housing to face the area you wish to illuminate.
GENERAL ELECTRICAL AND SAFETY WARNINGS
1) The AUTO/OFF switch on the main unit must be in the OFF posi-
on when changing baery.
2) Do not cut the solar cell wire. Disconnue use if the wire becomes
frayed or broken.
3) Do not immerse components in liquid.
4) Do not use any other charge than the single solar charging panel
provided with the SOLAR PIR SENSOR LIGHT. This may result in
injury or damage to the light and voids any warranty.
5) Posion so that the cord is securely fastened and will not result in
a hazard (such as tripping).
3
6) When changing baery, be careful of any sharp edges that could
cut you or the wires. Do not pull on wires.
CLEANING
It is important that the solar panel is kept free of dirt and debris. A
dirty solar panel will not allow the baery to fully charge and this will
shorten the life of baery and cause the light to malfuncon.
STORAGE
If you wish to store your light indoors for more than two or three
days, follow these steps to prevent damage to baery:
1. Turn the switch to OFF posion
2. Store the light and solar panel where it can receive some sunlight
or room light each day. The baery needs light to maintain a
charge during storage.
NOTE THE FOLLOWING TROUBLE-SHOOTING:
1. Symptom: Light doesn’t acvate in normal operaon.
Correcon: make sure that:
1) The main unit switch is at the AUTO posion.
2) The Lux control is not set too far toward ( )
3) The moon sensor is posioned to face oncoming movement
4) The solar cell is angled so that it gets plenty of direct sunlight for
most of day, if not the enre day.
5) Baery charge is not too low (charge for 3 sunny days—switch
turned to OFF)
2. Symptom: Light turns on during the day.
Correcon: Make sure that
1) The Lux control is not set too far toward ( )
3. Symptom: Light quickly flashes on and off
Correcon:
1) Move the Lux control toward ( )
2) Low baery (charge for 3 sunny days—switch turned to OFF).
4. Symptom: Light is not as bright as normal.
Correcon:
1) Low baery (charge for 3 sunny days—switch turned to OFF).
4
Table of contents
Other Qazqa Outdoor Light manuals
Qazqa
Qazqa Grande FL Satin User manual
Qazqa
Qazqa Zaandam FL User manual
Qazqa
Qazqa Margarita FL 23 Black User manual
Qazqa
Qazqa Eva FL 1 User manual
Qazqa
Qazqa JeIena FL 2 User manual
Qazqa
Qazqa Terry GS User manual
Qazqa
Qazqa NAUTICA WL1 91857 User manual
Qazqa
Qazqa Frances FL 1 User manual
Qazqa
Qazqa NAUTICA WL 2 User manual
Qazqa
Qazqa Elif FL 1 Black Gold User manual
Qazqa
Qazqa NAUTICA WL 2 User manual
Qazqa
Qazqa NAUTICA WL 1 User manual
Qazqa
Qazqa Odense P50 Black User manual
Qazqa
Qazqa Shade 33 Globe White User manual
Qazqa
Qazqa Charlois WL Black Lux User manual
Qazqa
Qazqa 90495 User manual
Qazqa
Qazqa Simon WL 2 PIR User manual
Qazqa
Qazqa Stylish FL Satin 92023 User manual
Qazqa
Qazqa Big Cage FL 3 Black User manual
Qazqa
Qazqa Empoli FL Bronze CCT 2 User manual
Popular Outdoor Light manuals by other brands
Lindby
Lindby 9949029 Intended use
HEPER
HEPER DOGO Side LW6048.585-US Installation & maintenance instructions
HEPER
HEPER LW8034.003-US Installation & maintenance instructions
Maretti
Maretti VIBE S 14.6080.04.A quick start guide
BEGA
BEGA 84 253 Installation and technical information
HEPER
HEPER MINIMO Installation & maintenance instructions
LIGMAN
LIGMAN BAMBOO 3 installation manual
Maretti
Maretti TUBE CUBE WALL 14.4998.04 quick start guide
Maxim Lighting
Maxim Lighting Carriage House VX 40428WGOB installation instructions
urban ambiance
urban ambiance UQL1273 installation instructions
TotalPond
TotalPond 52238 instruction manual
Donner & Blitzen
Donner & Blitzen 0-02661479-2 owner's manual