Q-See 66300 User manual
WI-FI SMART DOORBELL
QUICK START GUIDE
ENGLISH / ESPAÑOL
TIMBRE INTELIGENTE WI-FI
GUÍA DE INICIO RÁPIDO
2
WELCOME!
Congratulations on your latest purchase and
welcome to the Q-See family. This guide will help get
your doorbell up and running.
WHAT’S INCLUDED
•(1) Wi-Fi Doorbell
•(1) Power Dongle
•(1) Hexagon Wrench
•(1) Mounting Bracket
•(3) Screws
•(1) Chime
•(1) Chime Wire Connector
•(4) Batteries
STEP 1
Before installing, please register your device on the
Q-See Support Portal at www.q-see.com/register
to receive critical updates and support for your
device. Registering will also help us to assist you with
any technical or warranty issues if ever necessary.
Please be sure to keep a record of your model
number(s) and to save this guide, as you will
need this information if you are ever in need
of technical or warranty support.
NOTE: Your username and password used to register
your device are not the same as those you use to log in
to your doorbell. Please write down your username, pass-
word, and model number(s) in the spaces provided below:
Username:
Password:
Model #:
3
STEP 2
Locate your breaker box and turn o the
breakers that give power to your doorbell
and chime before working with any wiring.
STEP 3
Go to your existing chime and remove the cover.
Your chime may look dierent than the one shown.
IMPORTANT: Visit www.q-see.com/support to
nd the most recent guides and up-to-date support
for your Q-See products.
NOTE: Battery-operated wireless chimes are not
compatible with the QCW1000 doorbell.
STEP 4
Loosen the screws enough to remove the two power
wires (They may be labeled “FRONT” and “TRANS”).
Straighten out the exposed wires and twist them at
the ends. Before the next step, take the included
chime wire connector and rmly open the two levers
(see photo in next step for reference).
4
STEP 5
Insert either chime wire into either opening on the
chime wire connector. Be sure that the exposed
wire is securely inserted. Clamp the lever closed.
Repeat this step for the second wire.
The nished chime
wiring should look like
this. Replace the cover
on your chime and go
to your existing doorbell.
STEP 6
Unscrew or unmount your existing doorbell.
STEP 7
Disconnect the wiring that connects to the doorbell.
5
STEP 8
Install the included doorbell mounting bracket using
the supplied screws. Mount the bracket with the
screw hole at the bottom and facing away from the
wall. Ensure that the wires are pulled through the
bracket before mounting. Q-See suggests using a
level and marking drill holes with a pencil for this step.
STEP 9
Insert either doorbell wire into either connector
on the doorbell power dongle. Be sure that the
exposed wire is securely inserted. Clamp the lever
closed. Repeat this step for the second wire.
6
STEP 10
Push the power dongle connectors into the hole,
leaving only the doorbell power dongle exposed.
STEP 11
Plug the power dongle into the power port on the
back of the doorbell. Feed the extra wire back into the
wall and mount the doorbell to the bracket.
The two square slots on
the back of the doorbell
will need to align with
the mounting hooks at
the top of the mounting
bracket.
7
STEP 12
Align the mounting bracket hooks with the slots on
the back of the doorbell and push back, then down
to rmly slide the doorbell onto the bracket. You will
need to remove the doorbell from the bracket once
the power is turned on.
STEP 13
Go to your breaker box and turn on the power
breakers for the doorbell and chime.
STEP 15
Remove the doorbell
from the bracket and,
using a paper clip,
press the reset button
for 3 seconds. Return
the doorbell to the
mounting bracket
following step 12.
STEP 14
Download the Q-See Plus app
from the App Store on your mobile
device. Once installed, ensure that
your mobile device is connected
to the Wi-Fi network you wish to
use for your doorbell. Launch the
app on your mobile device.
ADDING THE
DOORBELL TO
Q-SEE PLUS
STEP 1
Tap on Register and
create a new Q-See
Plus account. If you
already have a Q-See
Plus account, skip to
step 5.
*All screenshots shown
are from the Q-See Plus
app on Android.
STEP 2
Enter an email
address to use for
your account. Tap
Send verication
code to mail. You
should immediately
receive an email with
a verication code. The verication code will work
for 24 hours. Be sure to check your spam/junk
folder if you do not receive the email.
STEP 3
Enter the verication
code and click Next.
8
STEP 4
Create a password
for your account. You
will enter the same
password twice to
conrm. Tap Register
to continue.
STEP 5
Enter your email
address again and
the new password.
Tap Login to
continue.
STEP 6
Tap the Add symbol to
continue. In the following
screen, select “Doorbell”
for device type.
STEP 7
In order to congure
your doorbell, you
will need to connect
your mobile device to
the Wi-Fi connection
coming from the
doorbell. Select
Congure Wi-Fi for
Device.
9
STEP 8
Go to your Settings
menu. Select your
Wi-Fi Settings
menu. Select the
DoorBell_ network.
STEP 10
Q-See Plus will Scan
for available Wi-Fi.
Select the Wi-Fi
Network you wish
to connect your
doorbell to.
STEP 11
Input the W-Fi
Password. Select
Save. If you enter the
password incorrectly,
the connection will
fail. Please verify the
password and retry.
NOTE: If you don’t see your doorbell network in this
list, try pressing the reset button on the back of your
doorbell and repeating step 6.
STEP 9
Once connected to
the doorbell Wi-
Fi, go back to the
Q-See Plus App.
Select Connected to
Hotspot, Continue.
10
Table of contents
Languages:
Other Q-See Accessories manuals
