30.08.2017
10. Drill the hole in the door where the
10mm in diameter to a depth not less than
11. Insert the bolt 6 in the outside of the
hitting it with a hammer.
12. Insert the deadbolt 5in the other side
manually tighten it to block. To provide
one may insert in the side of the
rod, a nail, a drill, an awl, etc. (
While installing the lock and the deadbolt, it is necessary to comply with their axial alignment within the permissible clear
of the deadbolt.
5.2 WIRING ORDER
The lock operates when applying and
switch (button). Controller installation is
Attention:
power of the lock is supplied by the voltage from 10 to 15 V of
When the power supply is on the lock is closed, when it is off the lock is open.
The wire assignment:
Red (black with red stripe) –
positive pole of the power supply;
Black –
negative pole of the power supply;
(The reverse polarity voltage supply
White, Green – sensor output of
Brown, Yellow – sensor output of
Provide reliable electrical contact. I
solate the connection points to
6. POSSIBLE FAILURES,
(more than 2.5mm) when the lock is
closed
The deadbolt does not hold the lock
(the door does not close)
The large gap is between the door
and the door frame during closing the
door (the deadbolt abuts to the lock)
door does not open. To open the
door needed to press it tighter to the
door frame
(automatic centering of the deadbolt
lacked), as a result the deadbolt
does not reach into the lock opening,
or when it reaches the lock, the
deadbolt clings
The deadbolt does not reach the end
of the lock opening ("balls are stuck")
min 16
10 8
3
5is fixing,
10mm in diameter to a depth not less than
14mm.
and press on it,
the door, and
easy tightening
opening a metal
).
13.
If it is necessary, arrange the length of the
14.
The lock installation is done
While installing the lock and the deadbolt, it is necessary to comply with their axial alignment within the permissible clear
ting the power supply, and for it
is usually used a controller (contro
ing to the technical data sheet.
power of the lock is supplied by the voltage from 10 to 15 V of
When the power supply is on the lock is closed, when it is off the lock is open.
positive pole of the power supply;
negative pole of the power supply;
not provide operability of the lock, but does not
;
.
solate the connection points to
avoid short-circuiting.
S AND TROUBLESHOOT
Reduce the length of the locking bolt
one hand, screw the locking bolt
to the nut with the other hand (or combination
pliers).
Set the lock in the "closed" status (turn on the vo
polarity and make sure that the power supply corresponds with the required
one.
Fix the knurled nut with one hand, unscrew the
the other hand (or combination pliers).
Fix the knurled nut with one hand, screw the
other hand (or combination pliers).
•Eliminate the causes
of loose fit of the door to the door frame.
•Use the door closer.
•Increase the length of the deadbolt.
Re-establish the door position. If it is impossible,
deadbolt from the door. Drill
out a hole in the door with a larger diameter.
Mount the deadbolt
on the door, providing alignment with the lock opening.
Turn off the power supply of the lock. Insert tightly
drill bit, etc.) with diameter 3-
5mm in the lock opening and pull it out.
provide
perpendicularity
surface!!!
If it is necessary, arrange the length of the
locking bolt.
The lock installation is done
.
While installing the lock and the deadbolt, it is necessary to comply with their axial alignment within the permissible clear
ance
is usually used a controller (contro
l board) or a
it).
, fix the knurled nut with
to the nut with the other hand (or combination
supply). Check the
polarity and make sure that the power supply corresponds with the required
from the nut with
to the nut with the
of loose fit of the door to the door frame.
the
out a hole in the door with a larger diameter.
on the door, providing alignment with the lock opening.
(screwdriver,
5mm in the lock opening and pull it out.
