Professional Entertainment Technology Viking VK910 User manual

LED 3x3 Matrix MOVING HEAD

User’s Manual

Viking VK910

Professional Entertainment Technology

1. Safety Instructions

WARNING

●Please keep this User Guide for future consultation. If you sell the unit to

another user, be sure that they also receive this instruction booklet

●DO NOT connect this product to the mains via a Dimmer

●Unpack and check carefully there is no transportation damage before us-

ing the unit.

●Before operating, ensure that the voltage and frequency of power supply

match the power requirements of the unit

●It’s important to ground the yellow/green conductor to earth in order to

avoid electric shock.

●The unit is for indoor use only. Use only in a dry location

●The unit must be installed in a location with adequate ventilation, at least

50cm from adjacent surfaces. Be sure that no ventilation slots are blocked

●Disconnect main power before replacement or servicing.

●Make sure there are no flammable materials close to the unit while

operating as it is fire hazard.

●Use safety bonds when hanging this unit. Don’t handle the unit by

taking its head only, always hold by the base handles.

●Maximum ambient temperature is 40°C. Don't operate it where the

temperature is higher than this.

●Unit surface temperature may reach up to 85°C. Don’t touch the housing

bare-hand during its operation. Turn off the power and allow about 15

minutes for the unit to cool down before replacing or serving.

●In the event of a serious operating problem, stop using the unit

immediately. Never try to repair the unit by yourself. Repairs carried out by

unskilled people can lead to damage or malfunction. Please contact the

nearest Viking Dealer for assistance.

●To prevent or reduce the risk of electrical shock or fire, do not expose the

unit the rain or moisture. The unit is for indoor use only. Use only in a dry

location.

●The housing, the lenses, or the ultraviolet filter must be replaced if they

are visibly damaged.

Please read carefully the instructions, which includes important

information about the installation,usage and maintenance

Caution

There are no user serviceable parts inside the unit. Do not open the housing or

attempt any repairs yourself. In the unlikely event your unit may require service,

please contact your nearest Viking Lighting dealer.

Installation

The unit should be mounted via its screw holes on the omega bracket. Always

ensure that the unit is firmly fixed to avoid vibration and slipping white operating.

Make sure that the structure to which you are attaching the unit is secure and is

able to support a weight of 10 times of the unit’s weight. Also always use a safety

cable rated to 15kg SWL when installing the fixture from the Omega Hanging

Bracket.

The equipment must be fixed by professionals who have accessed it’s use is

safe and proper.

2. Technical Specification

●Extremely small, fast and powerful LED Moving beam.

●DMX Channels:1/16/48 Channel Modes

●Master, Slave, Sound & DMX Modes

●Pan/Tilt: 540 /270 degrees speed adjustable

●Smooth electronic dimming:0-100%

●Electronic strobe with pulse and random effects

●High efficiency, low power consumption, low noise

●Super compact, low weight, fast moving

●Powercon in and out connectors

●DMX on 3 pin in and out XLR connectors

●All 9 Led individually controllable

●Built In Programs

●9 x 10w 4in1 Quad Colour LED

●Weight: 7.5kg

●Voltage: 100-240v 50/60hz 120w

●Fuse: External T6.3a 20mm

●Dimensions: 292x187x324mm

3 DMX512 Connection

1. If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin

adapter-cable. Route signal cables away from mains cables to avoid

signal interference - commonly viewed as lights flickering randomly.

2. At the last unit, the DMX cable has to be terminated with a terminator. Solder a

120 ohm 1/4w resistor between pin 2(DMX-)and pin 3(DMX+)into a 3-pin XLR-

plug and plug it in the DMX-output of the last unit

3. Connect the unit together in a daisy chain by XLR plug from the output of the

unit to the input of the next unit. The cable cannot branched or split to a

‘Y’cable. DMX512 is a very high-speed signal. Inadequate or damaged cables,

soldered joints or corroded connectors can easily distort the signal and shut

down the systems.

4. The DMX output and input connectors are pass-through to maintain the DMX

circuit, when one of the units power is disconnected.

5. Each light needs to have an address set to receive the data sent by the con-

troller. The address number is between 1-512

6. 3 pin XLR connectors are equally as popular as 5 pin XLR

In both cases the following protocol applies;

XLR: Pin 1:GND Pin 2:Negative signal(-) Pin 3:Positive signal(+)

Termination reduces signal errors and avoids signal

transmission problems & interference. It is always

advisable to connect a DMX signal terminator At the

end of the signal run. (See Point 2 below)

Display

To show the various menus and the selected functions

LED

Button

DMX On DMX Input Present

MASTER On Master Mode

SLAVE On Slave Mode

SOUND Flashing Sound Activation

MENU To select the appropriate option

DOWN To go backward in the selected function

UP To go forward in the selected function

ENTER To confirm the selected value or function

4. Main Function

To select any of the given functions, Press the MENU button until the required

function is showing on the display. Select the function by pressing the ENTER

button and the display will blink.

Use the DOWN and UP button to change the mode. Once the required mode

has been selected, press the ENTER button to confirm selection or to go back

to the functions without any change press the MENU button again. Hold and

press the MENU button about one second or wait for one minute to exit the

menu mode.

The main functions are showing overleaf:

Display Value Function

DMX Address 0-512 Select DMX starting address for the light

Channel Set Xch Select DMX Channel Mode 10 13 or 17 control channels

Show Mode Show x Select inbuilt show 1 2 3 or 4

Slave Set SlaveX Select either slave1 (normal) or slave2 for light show slave

Blackout Yes / No Select if you wish the unit to blackout in loss of DMX signal

Sound Mode On / Off Select if the auto sound trigger is on or off

Sound Sense 0 / 100 Select sensitivity of built in mic to trigger sound activation

Pan Inverse Yes / No Invert Pan on Head

Tilt Inverse

Yes / No

Invert Tilt on Head

Back Light On / Off Select if LCD backlight is to be constantly on or auto off

White Balance R/G/B 0-255 Reset the head to factory defaults

Fixture Test Function 0-

255

Manual test RGBW Dimmer & Strobe functions

Temp Shows the internal temperature of the head

Defaults Yes/No

Pro/Auto

Reset to factory defaults - either Pro or Auto (basic) level

Fixture Reset Yes/No Reset fixture

DMX Address

Select DMX Address,Press the ENTER button to confirm, the present address

will blink on the display. Use the UP and DOWN button to adjust the address

from 1to 512. Once the address has been selected,press the ENTER button to

setup,to go back to the functions without any change press the MENU button

again. Hold and press the MENU button about one second or wait for one minute

to exit the menu mode

DMX Channel Set

Select Channel Set,Press the ENTER button to confirm, the present set will

blink on the display. Use the UP and DOWN button to select channel 1/16/48.

Once the set has been selected,press the ENTER button to setup,to go back to

the functions without any change press the MENU button again. Hold and press

the MENU button about one second or wait for one minute to exit the menu

mode

Show Mode

Select Show Mode,Press the ENTER button to confirm, present mode will blink

on the display. Use the DOWN and UP button to select the Show 1 or Show 2 or

Show 3 or Show 4 mode. Once the mode has been selected,press the ENTER

button to setup,to go back to the functions without any change press the MENU

button again. Hold and press the MENU button about one second or wait for one

minute to exit the menu mode

Slave Mode

Select Slave Mode,Press the ENTER button to confirm, present mode will blink

on the display. Use the DOWN and UP button to select the Slave 1(normal) or

Slave 2 (2 light show)mode. Once the mode has been selected,press the EN-

TER button to setup,to go back to the functions without any change press the

MENU button again. Hold and press the MENU button about one second or wait

for one minute to exit the menu mode

Black Out (DMX Fail)

Select Slave Mode,Press the ENTER button to confirm, present mode will blink

on the display. Use the DOWN and UP button to select the Yes(yes blackout) or

No (no blackout)mode. Once the mode has been selected,press the ENTER but-

ton to setup,to go back to the functions without any change press the MENU but-

ton again. Hold and press the MENU button about one second or wait for one

minute to exit the menu mode

Sound State (Mic on/Off)

To set sound control on or off (disenabled) select Sound State, Press the ENTER

button to confirm, present mode will blink on the display. Use the DOWN and UP

button to select the On(Sound On) or Off (Sound Off)mode. Once the mode has

been selected,press the ENTER button to setup,to go back to the functions without

any change press the MENU button again. Hold and press the MENU button about

one second or wait for one minute to exit the menu mode

Sound Sense (Sensitivity)

To set the sensitivity of the built in microphone select Sound Sense, Press the

ENTER button to confirm, present mode will blink on the display. Use the DOWN

and UP button to select the 0…100 mode. Once the mode has been selected,press

the ENTER button to setup,to go back to the functions without any change press

the MENU button again. Hold and press the MENU button about one second or

wait for one minute to exit the menu mode

Pan Inverse

Select Pan Inverse,Press the ENTER button to confirm, present mode will blink on

the display. Use the DOWN and UP button to select the Yes(Pan Inversion) or

No((Normal)mode. Once the mode has been selected,press the ENTER button to

setup,to go back to the functions without any change press the MENU button again.

Hold and press the MENU button about one second or wait for one minute to exit

the menu mode

Tilt Inverse

Select Tilt Inverse,Press the ENTER button to confirm, present mode will blink on

the display. Use the DOWN and UP button to select the Yes(Tilt Inversion) or

No((Normal)mode. Once the mode has been selected,press the ENTER button to

setup,to go back to the functions without any change press the MENU button again.

Hold and press the MENU button about one second or wait for one minute to exit

the menu mode

Back Light (LCD backlight)

Select Back Light,Press the ENTER button to confirm, present mode will blink

on the display. Use the DOWN and UP button to select the On(LED On) or

Off((LED Off)mode. Once the mode has been selected,press the ENTER button

to setup,to go back to the functions without any change press the MENU button

again. Hold and press the MENU button about one second or wait for one minute

to exit the menu mode

White Balance

Select White Balance, press the ENTER button to confirm, present

mode will blink on the display. Use the DOWN and UP button to select

the Red or Green or Blue. Once the mode has been selected, press

the ENTER button to setup, use the DOWN and UP button to change

the value (125~255). Once the mode has been selected, press the

ENTER button to setup, go back to the functions without any change

press the MENU button again. Hold and press the MENU button about

one second or wait for one minute to exit the menu mode.

Manu Test (Manual Test)

Select Manu Test, press the ENTER button to confirm, present mode

will blink on the display. Use the DOWN and UP button to select the

Pan/ Tilt/Red/Green/Blue/ White/Dimmer or Strobe. Once the

mode has been selected, press the ENTER button to setup,use the

DOWN and UP button to change the value (0~255). Once the mode

has been selected, press the ENTER button to setup, go back to the

functions without any change press the MENU button again. Hold and

press the MENU button about one second or wait for one minute to

exit the menu mode.

Fixture Test

Select Manu Test, press the ENTER button to confirm, present mode

will blink on the display. Once the mode has been selected, press the

ENTER button to setup, go back to the functions without any change

press the MENU button again. Hold and press the MENU button about

one second or wait for one minute to exit the menu mode.

Temperature

Press the MENU button up to when the Temp is blinking on the

display. Pressing ENTER button and the display will show the

temperature of the unit. To go back to the functions press the MENU

button again. Hold and press the MENU button about one second or

wait for one minute to exit the menu mode.

Defaults Setting

Press the MENU button to show Defaults on the display. Press the

ENTER button and the display will blink. Use the DOWN and UP

button to select the YES or No. Once the Yes has been selected,

press the ENTER button and use the UP and Down button to select

the PRO Defaults or AUTO Defaults.

PRO Defaults: For professional users:

Slave Mode = Slave 1

Black Out = Yes

Sound State = Off

Pan Inverse = No

Tilt Inverse = No

Back Light = Off

Function Delay = 3S Delay

AUTO Defaults: Mostly automatic mode, for non professional users:

Slave Mode = Slave 1

Black Out = No

Sound State = On

Pan Inverse = No

Tilt Inverse = No

Back Light = On

Reset

Press the MENU button until Reset is blinking on the display. Pressing the

ENTER button will reset the head and all channels of the unit will return to their

standard position.

Table of contents

Other Professional Entertainment Technology Floodlight manuals

Professional Entertainment Technology

Professional Entertainment Technology BEAM-2R/PRO User manual

Popular Floodlight manuals by other brands

VIZULO

VIZULO Micro Martin Mounting instruction

EuroLite

EuroLite LED IP FL-100 SMD user manual

Cooper Wheelock

Cooper Wheelock XB12 specification

Allen + Roth

Allen + Roth 17624-000 user manual

ADJ

ADJ 4 STAGE PAK User instructions

Cooper Lighting

Cooper Lighting EGL91SW233 Specification sheet

Max

Max 37496 instruction manual

BEGA

BEGA 85 143 Instructions for use

Beamz

Beamz 151.226 user manual

EuroLite

EuroLite LED IP FL-8 user manual

Ledj

Ledj PERFORMER 36 RGB user manual

Perel

Perel ELS3 user manual

Perel

Perel ELS3WD user manual

LumX

LumX LM 36130 instruction manual

Xtricity

Xtricity 4-80053 instructions

Stahl

Stahl 6521/4 Series operating instructions

Ecosense

Ecosense EcoSpec installation manual

Ayrton

Ayrton minipanel FX manual